Generalized Three-Dimensional Heat Source Problem for Small Time

Author(s):  
Moncef Aouadi
2021 ◽  
Vol 110 ◽  
pp. 102583
Author(s):  
Elona Fetahu ◽  
Oguz Yilmaz

Volume 1 ◽  
2004 ◽  
Author(s):  
T. Roy ◽  
R. S. Amano ◽  
J. Jatkar

Soil remediation process by heated soil vapor extraction system has drawn considerably attention for the last few years. The areas around chemical companies or waste disposal sites have been seriously contaminated from the chemicals and other polluting materials that are disposed off. Our present study is concentrated on modeling one transient Heated Soil Vapor Extraction System and predicting the time required for effective remediation. The process developed by Advanced Remedial Technology, consists of a heating source pipe and the extraction well embedded in the soil. The number of heat source pipes and the extraction wells depends on the type of soil, the type of pollutants, moisture content of the soil and the size of the area to be cleaned. The heat source heats the soil, which is transported in the interior part of the soil by means of conduction and convection. This heating of soil results in vaporization of the gases, which are then driven out of the soil by the extraction well. The extraction well consists of the blower which would suck the vaporized gases out of the system. A three-dimensional meshed geometry was developed using gambit. Different boundary conditions were used for heating and suction well and for other boundaries. Concentrations of different chemicals were collected from the actual site and this data was used as an initial condition. The analysis uses the species transport and discrete phase modeling to predict the time required to clean the soil under specific conditions. This analysis could be used for predicting the changes of chemical concentrations in the soil during the remediation process. This will give us more insight to the physical phenomena and serve as a numerical predictive tool for more efficient process.


1991 ◽  
Vol 37 (125) ◽  
pp. 89-96 ◽  
Author(s):  
Garry K. C. Clarke ◽  
Edwin D. Waddington

AbstractQuantitative understanding of the processes that couple the lower atmosphere to the upper surface of ice sheets is necessary for interpreting ice-core records. Of special interest are those processes that involve the exchange of energy or atmospheric constituents. One such process, wind pumping, entails both possibilities and provides a possible mechanism for converting atmospheric kinetic energy into a near-surface heat source within the firn layer. The essential idea is that temporal and spatial variations in surface air pressure, resulting from air motion, can diffuse into permeable firn by conventional Darcy flow. Viscous friction between moving air and the solid firn matrix leads to energy dissipation in the firn that is equivalent to a volumetric heat source.Initial theoretical work on wind pumping was aimed at explaining anomalous near-surface temperatures measured at sites on Agassiz Ice Cap, Arctic Canada. A conclusion of this preliminary work was that, under highly favourable conditions, anomalous warming of as much as 2°C was possible. Subsequent efforts to confirm wind-pumping predictions suggest that our initial estimates of the penetration depth for pressure fluctuations were optimistic. These observations point to a deficiency of the initial theoretical formulation — the surface-pressure forcing was assumed to vary temporally, but not spatially. Thus, within the firn there was only a surface-normal component of air flow. The purpose of the present contribution is to advance a three-dimensional theory of wind pumping in which air flow is driven by both spatial and temporal fluctuations in surface pressure. Conclusions of the three-dimensional analysis are that the penetration of pressure fluctuations, and hence the thickness of the zone of frictional interaction between air and permeable firn, is related to both the frequency of the pressure fluctuations and to the spatial coherence length of turbulence cells near the firn surface.


2017 ◽  
Vol 139 (2) ◽  
Author(s):  
Srivathsan Sudhakar ◽  
Justin A. Weibel

For thermal management architectures wherein the heat sink is embedded close to a dynamic heat source, nonuniformities may propagate through the heat sink base to the coolant. Available transient models predict the effective heat spreading resistance to calculate chip temperature rise, or simplify to a representative axisymmetric geometry. The coolant-side temperature response is seldom considered, despite the potential influence on flow distribution and stability in two-phase microchannel heat sinks. This study solves three-dimensional transient heat conduction in a Cartesian chip-on-substrate geometry to predict spatial and temporal variations of temperature on the coolant side. The solution for the unit step response of the three-dimensional system is extended to any arbitrary temporal heat input using Duhamel's method. For time-periodic heat inputs, the steady-periodic solution is calculated using the method of complex temperature. As an example case, the solution of the coolant-side temperature response in the presence of different transient heat inputs from multiple heat sources is demonstrated. To represent a case where the thermal spreading from a heat source is localized, the problem is simplified to a single heat source at the center of the domain. Metrics are developed to quantify the degree of spatial and temporal nonuniformity in the coolant-side temperature profiles. These nonuniformities are mapped as a function of nondimensional geometric parameters and boundary conditions. Several case studies are presented to demonstrate the utility of such maps.


Sign in / Sign up

Export Citation Format

Share Document