Properties of self-consolidating concrete containing high-volume supplementary cementitious materials and nano-limestone

2014 ◽  
Vol 3 (3-4) ◽  
pp. 245-255 ◽  
Author(s):  
Xin Wang ◽  
Kejin Wang ◽  
Jinxin Li ◽  
Nishant Garg ◽  
Surendra P. Shah
Keyword(s):  
High Volume ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Self Consolidating Concrete

EFFECT OF ACCELERATED CURING ON ABRASION OF HIGH VOLUME SUPPLEMENTARY CEMENTITIOUS MATERIAL SELF CONSOLIDATING CONCRETE

2015 ◽  
Vol 2 (1) ◽  
Author(s):  
Hayder H. Alghazali ◽  
John J. Myers
Keyword(s):  
Prestressed Concrete ◽  
Abrasion Resistance ◽  
High Volume ◽  
Cementitious Materials ◽  
Cementitious Material ◽  
Supplementary Cementitious Materials ◽  
Supplementary Cementitious Material ◽  
Self Consolidating Concrete ◽  
Accelerated Curing ◽  
Precast Prestressed Concrete

Sustainability of precast/prestressed concrete plant can be promoted by using supplementary cementitious material and that significantly reduces the embodied energy of precast/ prestressed concrete products. Usually, up to 25% of the cement can be replaced with supplementary cementitious materials (SCM). Increasing the level of replacement to exceed 25% is considered to be High-Volume SCM. Appropriate testing should be conducted to ensure desired performance of the concrete. This context reports the results of an experimental investigation of effect of accelerated curing on abrasion resistance of High Volume Supplementary Cementitious Material – Self Consolidating Concrete (HVSCM-SCC). Different mixes proportion with supplementary cementitious materials such as Fly Ash, Micro Silica, and lime (Up to 75% of cement replacement) were tested. Rheological properties of the HVSCM-SCC were measured. Mechanical properties at different ages 1, 3, 7, 28, 56, and 90 days were monitored. To investigate the abrasion resistance, 12 x 12 x 3.5 in specimens at age of 28, 56, and 90 days were conducted. The results of abrasion resistance of HVSCM-SCC were compared to the same mixes cured in the moist room. The result showed that the accelerated curing has a significant influence on abrasion resistance of concrete at early ages.

Use of Fiber-Reinforced Self-Consolidating Concrete to Enhance Serviceability Performance of Damaged Beams

2018 ◽  
Vol 2672 (27) ◽  
pp. 45-55 ◽  
Author(s):  
Haider A. Abdulhameed ◽  
Hani Nassif ◽  
Kamal H. Khayat
Keyword(s):  
Polypropylene Fiber ◽  
Cementitious Materials ◽  
Load Level ◽  
Supplementary Cementitious Materials ◽  
Flexural Behavior ◽  
Experimental Program ◽  
Fiber Reinforced ◽  
Reinforcing Bars ◽  
Self Consolidating Concrete ◽  
Predicted Values

The use of fiber-reinforced self-consolidating concrete (FR-SCC) in repairing damaged concrete beams has been evaluated. An experimental program was conducted to design and test key fresh and hardened properties of SCC and FR-SCC mixtures. The designed FR-SCC mixtures included two types of supplementary cementitious materials (silica fume (SF) and slag (SL)) and two types of fibers (steel fiber (STF) and polypropylene fiber (PPF)) were used. To ensure good workability to repair congested areas, the optimized volume fractions of the STF were 0.25% and 0.50% compared with 0.10%, 0.15%, and 0.20% for the PPF. In addition, the flexural behavior of 10 beam specimens was investigated. The main reinforcement for the control beams consisted of #5 reinforcing bars, while the main reinforcement for the repaired beams was either #4 or #3 reinforcing bars that were introduced to simulate 35% and 65% reduction of the bar areas, respectively, due to corrosion. The results demonstrate that the optimized FR-SCC mixtures are effective repair materials and can develop adequate bond strength to existing concrete. The flexural test results showed that the repair mixtures were able to increase the cracking load for the repaired beams compared with the control beams. Such an increase is expected to contribute to extending the life of the damaged member or structure at the service load level. This paper also presents a comparison of the predicted values for the first-crack load strength using the ACI 544 code equation with the experimental data. Results showed that the code equation provides safe prediction.

scholarly journals Effect of Graphene Oxide Nanosheets on Physical Properties of Ultra-High-Performance Concrete with High Volume Supplementary Cementitious Materials

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1929 ◽  
Author(s):  
Yu-You Wu ◽  
Jing Zhang ◽  
Changjiang Liu ◽  
Zhoulian Zheng ◽  
Paul Lambert
Keyword(s):  
Graphene Oxide ◽  
Physical Properties ◽  
High Performance ◽  
High Performance Concrete ◽  
High Volume ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Ultra High Performance Concrete ◽  
Steam Curing ◽  
Slump Flow

Nanomaterials have been increasingly employed for improving the mechanical properties and durability of ultra-high-performance concrete (UHPC) with high volume supplementary cementitious materials (SCMs). Recently, graphene oxide (GO) nanosheets have appeared as one of the most promising nanomaterials for enhancing the properties of cementitious composites. To date, a majority of studies have concentrated on cement pastes and mortars with fewer investigations on normal concrete, ultra-high strength concrete, and ultra-high-performance cement-based composites with a high volume of cement content. The studies of UHPC with high volume SCMs have not yet been widely investigated. This paper presents an experimental investigation into the mini slump flow and physical properties of such a UHPC containing GO nanosheets at additions from 0.00 to 0.05% by weight of cement and a water–cement ratio of 0.16. The study demonstrates that the mini slump flow gradually decreases with increasing GO nanosheet content. The results also confirm that the optimal content of GO nanosheets under standard curing and under steam curing is 0.02% and 0.04%, respectively, and the corresponding compressive and flexural strengths are significantly improved, establishing a fundamental step toward developing a cost-effective and environmentally friendly UHPC for more sustainable infrastructure.

scholarly journals Sustainable low-carbon binders and concretes

2020 ◽  
Vol 166 ◽  
pp. 06007
Author(s):  
Myroslav Sanytsky ◽  
Tetiana Kropyvnytska ◽  
Stanislav Fic ◽  
Hanna Ivashchyshyn
Keyword(s):  
Activity Index ◽  
Chemical Properties ◽  
High Volume ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Cement Matrix ◽  
Low Carbon ◽  
Blended Cements ◽  
Physical And Chemical

Sustainable development depends on a consistency of interests, social, ecological and economic, and that the interests are evaluated in a balanced manner. In order to reduce CO2 emissions, the conception of decreasing clinker factor and increasing the role of supplementary cementitious materials (SCMs) in the cementitious materials has high economical and environmental efficiency. The performance of clinkerefficient blended cements with supplementary cementitious materials were examined. The influence of superfine zeolite with increased surface energy on the physical and chemical properties of low-carbon blended cements is shown. Increasing the dispersion of cementitious materials contributes to the growth of their strength activity index due to compaction of cement matrix and pozzolanic reactions in unclincker part. In consequence of the early structure formation and the directed formation of the microstructure of the cement matrix is solving the problem of obtaining clinker-efficient concretes. Shown that low-carbon blended cements with high volume of SCMs are suitable, in principle, for producing structural concretes.

Effect of Aggregate Max Size on the Rheological Properties of Self Consolidating Concrete

2020 ◽  
Vol 853 ◽  
pp. 193-197
Author(s):  
Samer Al Martini ◽  
Ziad Hassan ◽  
Ahmad Khartabil
Keyword(s):  
Blast Furnace Slag ◽  
Aggregate Size ◽  
Maximum Size ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Self Consolidating Concrete ◽  
Granulated Blast Furnace Slag ◽  
Concrete Mixtures ◽  
Time Period ◽  
Furnace Slag

The effects of aggregate size and supplementary cementitious materials (SCMs) on the rheology of self-consolidating concrete (SCC) were studied in this paper. Two main concrete mixtures with different maximum aggregate sizes were prepared and investigated. The first mix had a maximum size aggregate of 5 mm and the second mix was with 20 mm max size aggregates. All mixes incorporated different dosages of Ground granulated blast furnace slag (GGBS). The rheology of all mixes investigated was measured over 2 hour time period. It was found that the size of aggregates and GGBS dosage have influence on the yield stress of studied concrete mixes.

Sign in / Sign up

Export Citation Format

Share Document