scholarly journals Augmenting physical models with deep networks for complex dynamics forecasting*

2021 ◽  
Vol 2021 (12) ◽  
pp. 124012
Author(s):  
Yuan Yin ◽  
Vincent Le Guen ◽  
Jérémie Dona ◽  
Emmanuel de Bézenac ◽  
Ibrahim Ayed ◽  
...  

Abstract Forecasting complex dynamical phenomena in settings where only partial knowledge of their dynamics is available is a prevalent problem across various scientific fields. While purely data-driven approaches are arguably insufficient in this context, standard physical modeling-based approaches tend to be over-simplistic, inducing non-negligible errors. In this work, we introduce the APHYNITY framework, a principled approach for augmenting incomplete physical dynamics described by differential equations with deep data-driven models. It consists of decomposing the dynamics into two components: a physical component accounting for the dynamics for which we have some prior knowledge, and a data-driven component accounting for errors of the physical model. The learning problem is carefully formulated such that the physical model explains as much of the data as possible, while the data-driven component only describes information that cannot be captured by the physical model; no more, no less. This not only provides the existence and uniqueness for this decomposition, but also ensures interpretability and benefit generalization. Experiments made on three important use cases, each representative of a different family of phenomena, i.e. reaction–diffusion equations, wave equations and the non-linear damped pendulum, show that APHYNITY can efficiently leverage approximate physical models to accurately forecast the evolution of the system and correctly identify relevant physical parameters. The code is available at https://github.com/yuan-yin/APHYNITY.

Author(s):  
Gyujin Shim ◽  
Li Song ◽  
Gang Wang

In order to use real-time energy measurements to identify system operation faults and inefficiencies, a cooling coil energy baseline is studied in an air-handling unit (AHU) through an integration of physical models and a data driven approach in this paper. A physical model for an AHU cooling coil energy consumption is first built to understand equipment mechanism and to determine the variables impacting cooling coil energy performance, and then the physical model is simplified into a lumped model by reducing the number of independent variables needed. Regression coefficients in the lumped model are determined statistically through searching optimal fit using the least square method with short periods of measured data. Experimental results on an operational AHU (8 ton) are presented to validate the effectiveness of this approach with statistical analysis. As a result of this experiment, the proposed cooling energy baselines at the cooling coil have ±20% errors at 99.7% confidence. Six-day data for obtaining baseline is preferred since it shows similar results as 12-day.


Author(s):  
Takahiro Yamaguchi ◽  
Hajime Kimura ◽  
Atsushi Sakuma ◽  
Kazushige Takahashi ◽  
Shigetoshi Mimura

Sleeping is one of the most important factors that influence the quality of human life, and this state of existence should be thoroughly investigated to improve the quality of the life. The mechanical design of bedding has great influence on the comfort of a mattress. Thus, objective and conventional techniques to evaluate the mechanics of mattress comfort could help improve the quality of sleep. In this report, an analysis technique for the assessment of the sleeping posture of humans is presented to facilitate the development of mattress design technology. Herein, an analytical model which imitates the human body has been formulated to determine the design parameters of a mass-spring-joint system on a soft underlay. The physical model is composed of five components that represent the head, chest, hip, femur, and calf, with each body part being represented by a simple ball model. The spring joint connecting the five parts reflects the neck, lumbar, hip, and knee joints. The specifications of the body model are determined by actual measurements and previous studies. In order to determine the physical properties of the mattress, two types of mattress urethane foam material are tested using the ball indenter method. The parameters include Young’s modulus, plateau stress, and other physical parameters. Variation due to the type of mattress has been observed in the laying test using a pressure distribution sensor sheet. In the analysis performed using the physical model, the variation in the lying posture and the extent of body sinking are observed to be the same during experiments. Both variations are compared using the change in force distribution in each body part. In conclusion, it was found that the observed changes in distribution are the same in the experimental and physical models. Therefore, the proposed model reliably reflects the design characteristics of the mattress.


2003 ◽  
Vol 12 (06) ◽  
pp. 691-710 ◽  
Author(s):  
ISTVÁN PETRÁS ◽  
CSABA REKECZKY ◽  
TAMÁS ROSKA ◽  
RICARDO CARMONA ◽  
FRANCISCO JIMÉNEZ-GARRIDO ◽  
...  

This paper describes a full-custom mixed-signal chip that embeds digitally programmable analog parallel processing and distributed image memory on a common silicon substrate. The chip was designed and fabricated in a standard 0.5 μm CMOS technology and contains approximately 500 000 transistors. It consists of 1024 processing units arranged into a 32×32 grid. Each processing element contains two coupled CNN cores, thus, constituting two parallel layers of 32×32 nodes. The functional features of the chip are in accordance with the 2nd Order Complex Cell CNN-UM architecture. It is composed of two CNN layers with programmable inter- and intra-layer connections between cells. Other features are: cellular, spatial-invariant array architecture; randomly selectable memory of instructions; random storage and retrieval of intermediate images. The chip is capable of completing algorithmic image processing tasks controlled by the user-selected stored instructions. The internal analog circuitry is designed to operate with 7-bits equivalent accuracy. The physical implementation of a CNN containing second order cells allows real-time experiments of complex dynamics and active wave phenomena. Such well-known phenomena from the reaction–diffusion equations are traveling waves, autowaves, and spiral-waves. All of these active waves are demonstrated on-chip. Moreover this chip was specifically designed to be suitable for the computation of biologically inspired retina models. These computational experiments have been carried out in a developmental environment designed for testing and programming the analogic (analog-and-logic) programmable array processors.


2013 ◽  
Vol 54 (3) ◽  
pp. 153-170 ◽  
Author(s):  
RUNZHANG XU ◽  
YANBING YANG ◽  
SHAOHUA CHEN ◽  
JIA SU ◽  
JIHONG SHEN ◽  
...  

AbstractThis paper is concerned with the initial boundary value problem of a class of nonlinear wave equations and reaction–diffusion equations with several nonlinear source terms of different signs. For the initial boundary value problem of the nonlinear wave equations, we derive a blow up result for certain initial data with arbitrary positive initial energy. For the initial boundary value problem of the nonlinear reaction–diffusion equations, we discuss some probabilities of the existence and nonexistence of global solutions and give some sufficient conditions for the global and nonglobal existence of solutions at high initial energy level by employing the comparison principle and variational methods.


Sign in / Sign up

Export Citation Format

Share Document