scholarly journals Visualization and PIV-study of the formation of a cooling film when flowing around the leading edge of the gas turbine nozzle blade

2019 ◽  
Vol 1421 ◽  
pp. 012043
Author(s):  
S V Veretennikov ◽  
O A Evdokimov
Keyword(s):  
Gas Turbine ◽  
Leading Edge ◽  
Gas Turbine Nozzle ◽  
Nozzle Blade

scholarly journals Effects of Nonuniform Blade Pitch on the Flow Through an Annular Turbine Nozzle

1995 ◽  
Vol 2 (1) ◽  
pp. 59-65 ◽  
Author(s):  
Rainer Kurz
Keyword(s):  
Gas Turbine ◽  
Flow Measurement ◽  
Static Pressure ◽  
Leading Edge ◽  
Inviscid Flow ◽  
Viscous Effect ◽  
Measurement Results ◽  
Flow Through ◽  
The Mean ◽  
Gas Turbine Nozzle

This paper discusses flow measurement results both upstream and downstream of a transonic annular gas turbine nozzle with a nonuniform pitch. The downstream measurements are performed in the plane where the leading edge of the rotor blade is located in the gas turbine. The experiments were performed using total pressure probes and wall static pressure taps. The pitch variation modifies the flow field both upstream and downstream of the nozzle, although the experiments show that the effect is localized to the immediate neighborhood of the involved blades. The effects on the wakes and on the inviscid flow are discussed separately. The mean velocities show a strong sensitivity to the changes of the pitch, which is due to a potential flow effect rather than a viscous effect.

Recent Advances in the Study of Film Cooling on the Gas Turbine Blade

2014 ◽  
Vol 971-973 ◽  
pp. 143-147 ◽  
Author(s):  
Ping Dai ◽  
Shuang Xiu Li
Keyword(s):  
Gas Turbine ◽  
Turbine Blade ◽  
Film Cooling ◽  
Gas Turbines ◽  
High Performance ◽  
Leading Edge ◽  
Development Trend ◽  
Research Progress ◽  
Gas Turbine Blade ◽  
New Generation

The development of a new generation of high performance gas turbine engines requires gas turbines to be operated at very high inlet temperatures, which are much higher than the allowable metal temperatures. Consequently, this necessitates the need for advanced cooling techniques. Among the numerous cooling technologies, the film cooling technology has superior advantages and relatively favorable application prospect. The recent research progress of film cooling techniques for gas turbine blade is reviewed and basic principle of film cooling is also illustrated. Progress on rotor blade and stationary blade of film cooling are introduced. Film cooling development of leading-edge was also generalized. Effect of various factor on cooling effectiveness and effect of the shape of the injection holes on plate film cooling are discussed. In addition, with respect to progress of discharge coefficient is presented. In the last, the future development trend and future investigation direction of film cooling are prospected.

scholarly journals Investigations on the Blade Vibration of a Radial Inflow Micro Gas Turbine Wheel

2007 ◽  
Vol 2007 ◽  
pp. 1-10 ◽  
Author(s):  
Shijie Guo
Keyword(s):  
Gas Turbine ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Turbine Blades ◽  
Pressure Fluctuations ◽  
Leading Edge ◽  
Coupled Modes ◽  
Blade Vibration ◽  
Turbine Wheel ◽  
Micro Gas Turbine

This paper demonstrates the investigations on the blade vibration of a radial inflow micro gas turbine wheel. Firstly, the dependence of Young's modulus on temperature was measured since it is a major concern in structure analysis. It is demonstrated that Young's modulus depends on temperature greatly and the dependence should be considered in vibration analysis, but the temperature gradient from the leading edge to the trailing edge of a blade can be ignored by applying the mean temperature. Secondly, turbine blades suffer many excitations during operation, such as pressure fluctuations (unsteady aerodynamic forces), torque fluctuations, and so forth. Meanwhile, they have many kinds of vibration modes, typical ones being blade-hub (disk) coupled modes and blade-shaft (torsional, longitudinal) coupled modes. Model experiments and FEM analysis were conducted to study the coupled vibrations and to identify the modes which are more likely to be excited. The results show that torque fluctuations and uniform pressure fluctuations are more likely to excite resonance of blade-shaft (torsional, longitudinal) coupled modes. Impact excitations and propagating pressure fluctuations are more likely to excite blade-hub (disk) coupled modes.

Experimental Studies of Leading Edge Contouring Influence on Secondary Losses in Transonic Turbines

2012 ◽  
Author(s):  
Ranjan Saha ◽  
Jens Fridh ◽  
Torsten Fransson ◽  
Boris I. Mamaev ◽  
Mats Annerfeldt
Keyword(s):  
Gas Turbine ◽  
Guide Vane ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Leading Edge ◽  
Secondary Flows ◽  
Noticeable Effect ◽  
Flow Angle ◽  
Wide Range ◽  
Contour Plots

An experimental study of the hub leading edge contouring using fillets is performed in an annular sector cascade to observe the influence of secondary flows and aerodynamic losses. The investigated vane is a three dimensional gas turbine guide vane (geometrically similar) with a mid-span aspect ratio of 0.46. The measurements are carried out on the leading edge fillet and baseline cases using pneumatic probes. Significant precautions have been taken to increase the accuracy of the measurements. The investigations are performed for a wide range of operating exit Mach numbers from 0.5 to 0.9 at a design inlet flow angle of 90°. Data presented include the loading, fields of total pressures, exit flow angles, radial flow angles, as well as profile and secondary losses. The vane has a small profile loss of approximately 2.5% and secondary loss of about 1.1%. Contour plots of vorticity distributions and velocity vectors indicate there is a small influence of the vortex-structure in endwall regions when the leading edge fillet is used. Compared to the baseline case the loss for the filleted case is lower up to 13% of span and higher from 13% to 20% of the span for a reference condition with Mach no. of 0.9. For the filleted case, there is a small increase of turning up to 15% of the span and then a small decrease up to 35% of the span. Hence, there are no significant influences on the losses and turning for the filleted case. Results lead to the conclusion that one cannot expect a noticeable effect of leading edge contouring on the aerodynamic efficiency for the investigated 1st stage vane of a modern gas turbine.

Simple Instrumentation Rake Designs for Gas Turbine Engine Testing

1996 ◽  
Author(s):  
Peter D. Smout ◽  
Steven C. Cook
Keyword(s):  
Gas Turbine ◽  
Mechanical Damage ◽  
Engine Performance ◽  
Leading Edge ◽  
Gas Turbine Engine ◽  
Calibration Data ◽  
Turbine Engine ◽  
Industry Standard ◽  
Repair Costs ◽  
Engine Testing

The determination of gas turbine engine performance relies heavily on intrusive rakes of pilot tubes and thermocouples for gas path pressure and temperature measurement. For over forty years, Kiel-shrouds mounted on the rake body leading edge have been used as the industry standard to de-sensitise the instrument to variations in flow incidence and velocity. This results in a complex rake design which is expensive to manufacture, susceptible to mechanical damage, and difficult to repair. This paper describes an exercise aimed at radically reducing rake manufacture and repair costs. A novel ’common cavity rake’ (CCR) design is presented where the pressure and/or temperature sensors are housed in a single slot let into the rake leading edge. Aerodynamic calibration data is included to show that the performance of the CCR design under uniform flow conditions and in an imposed total pressure gradient is equivalent to that of a conventional Kiel-shrouded rake.

Computational Aid to AEDsys for Designing a Variable-Area Gas Turbine Nozzle

2018 ◽  
Author(s):  
Devin O. O’Dowd ◽  
Aaron R. Byerley
Keyword(s):  
Gas Turbine ◽  
United States Air Force ◽  
System Analysis ◽  
Graphical Representation ◽  
Aircraft Engine ◽  
The United States ◽  
Design System ◽  
Engine Design ◽  
Critical Feedback ◽  
Gas Turbine Nozzle

This paper presents a practical approach to designing a gas turbine nozzle with the help of the Aircraft Engine Design textbook as well as the software program Nozzle, a subprogram within the Aircraft Engine Design System Analysis Software suite AEDsys. The current textbook and software allow for a variable wetted length of the converging and diverging nozzle sections. Critical feedback from industry experts has inspired an attempt to design a nozzle with fixed wetted material lengths. This paper is written to augment classroom treatment, but will also support others who use the Aircraft Engine Design text and software for a preliminary engine design capstone. This approach is further guided by the actual scaling of the Pratt & Whitney F100 variable geometry converging-diverging nozzle, where wetted lengths are fixed. The chief goal is to equip students at the United States Air Force Academy with a refined approach that is more realistic of a manufactured nozzle design, producing a graphical representation of a nozzle schedule at different speed and altitude flight conditions, both with and without afterburner.

Computational Design and Experimental Evaluation of Using a Leading Edge Fillet on a Gas Turbine Vane

2001 ◽  
Author(s):  
G. A. Zess ◽  
K. A. Thole
Keyword(s):  
Boundary Layer ◽  
Flow Field ◽  
Pressure Gradient ◽  
Gas Turbine ◽  
Total Pressure ◽  
Guide Vane ◽  
Leading Edge ◽  
Field Measurements ◽  
Computational Design ◽  
Horseshoe Vortex

With the desire for increased power output for a gas turbine engine comes the continual push to achieve higher turbine inlet temperatures. Higher temperatures result in large thermal and mechanical stresses particularly along the nozzle guide vane. One critical region along a vane is the leading edge-endwall juncture. Based on the assumption that the approaching flow to this juncture is similar to a two-dimensional boundary layer, previous studies have shown that a horseshoe vortex forms. This vortex forms because of a radial total pressure gradient from the approaching boundary layer. This paper documents the computational design and experimental validation of a fillet placed at the leading edge-endwall juncture of a guide vane to eliminate the horseshoe vortex. The fillet design effectively accelerated the incoming boundary layer thereby mitigating the effect of the total pressure gradient. To verify the CFD studies used to design the leading edge fillet, flow field measurements were performed in a large-scale, linear, vane cascade. The flow field measurements were performed with a laser Doppler velocimeter in four planes orientated orthogonal to the vane. Good agreement between the CFD predictions and the experimental measurements verified the effectiveness of the leading edge fillet at eliminating the horseshoe vortex. The flowfield results showed that the turbulent kinetic energy levels were significantly reduced in the endwall region because of the absence of the unsteady horseshoe vortex.

Sign in / Sign up

Export Citation Format

Share Document