scholarly journals Microclimate measurements in ventilated air gaps – instrumentation and first results

2021 ◽  
Vol 2069 (1) ◽  
pp. 012200
Author(s):  
P Rüther ◽  
O Oksavik ◽  
A Nocente ◽  
L Gullbrekken
Keyword(s):  
Test Methods ◽  
Climatic Conditions ◽  
Air Gap ◽  
Air Gaps ◽  
Temperature Conditions ◽  
Energy Efficient Buildings ◽  
First Results ◽  
Wind Barrier ◽  
Temperature Levels ◽  
Set Up

Abstract To achieve energy efficient buildings, the requirements for air tightness in Norway were strengthened in the recent years. Thus, the use of tape for tightening connections and overlaps in the wind barrier and vapour barrier layer has become more and more common. Since these products are covered by a façade cladding and hence difficult to access, they need to maintain their performance level over many years, usually 25 to 30 years. To design test methods to ensure the performance of tapes and other products used in the ventilated air gap, more knowledge on the climatic conditions, especially temperature conditions, is needed. The recently finished ZEB Lab building in Trondheim, Norway, has been instrumented with thermocouples to monitor the temperature conditions in the air gap. This study presents the instrumentation set up and first findings from the start of the experiment in summer 2020. First results show temperature levels up to 76°C in the upper part of the roof construction.

Evaluation of Measurement in Crawl Space of Wooden House

2016 ◽  
Vol 835 ◽  
pp. 501-505
Author(s):  
Sarka Korbelova ◽  
Lucie Kucerova
Keyword(s):  
Energy Efficient ◽  
Climatic Conditions ◽  
Air Gap ◽  
Point Of View ◽  
The Czech Republic ◽  
Technical Point ◽  
Energy Efficient Buildings ◽  
Wooden House ◽  
Crawl Space ◽  
Humidity Field

The society lays stress on today's buildings, particularly in terms of energy-efficient buildings and ecology of buildings. Accordingly, not only from a technical technical point of view, it is important to give sufficient attention to the foundations of building. The popular way of foundation of lightweight buildings is due to the growing interest in timber houses the foundation above a ventilated air gap so called Crawl Space. The article deals with the temperature and humidity field which is located in the air gap under the construction of wooden building in the climatic conditions of the Czech Republic.

scholarly journals Endoscopic Pan/Tilt Camera for Thorax Interventions – Design and first results

2019 ◽  
Vol 5 (1) ◽  
pp. 517-519
Author(s):  
Alexander Mrokon ◽  
Peter P. Pott ◽  
Volker Steger
Keyword(s):  
Minimally Invasive ◽  
Inclination Angle ◽  
Magnetic Circuit ◽  
Mechanical Stability ◽  
Fem Simulation ◽  
Camera System ◽  
Design Changes ◽  
First Results ◽  
Set Up ◽  
Future Work

AbstractMinimally invasive surgery in some cases suffers from a limited view because certain areas are obscured by others. In this paper, a system is described, which can be used in minimally invasive procedures as an addition to a standard endoscope to improve the range of view. Through FEM simulation a magnetic circuit was designed to position the camera head. Subsequently, a camera positioning system was set up that includes an extracorporeal and an intracorporeal unit. The first controls the intracorporeal system. The latter has a camera inclination angle of up to 65° and an additional vertically downward viewing angle when aligned in parallel (inclination angle 0°). The panning angle is 360°. The camera system was evaluated in lab and cadaver trials. It has been found that the size of the intracorporeal system (16 × 10 × 150 mm) represents a major problem. Future work will focus of the reduction of the system’s size, the improvement of the camera image quality, and design changes considering mechanical stability.

scholarly journals Do air-gaps behind soft body armour affect protection?

2017 ◽  
Vol 164 (1) ◽  
pp. 15-18 ◽  
Author(s):  
Lee Tilsley ◽  
D J Carr ◽  
C Lankester ◽  
C Malbon
Keyword(s):  
Ceramic Composite ◽  
Air Gap ◽  
The Body ◽  
Gap Size ◽  
Soft Body ◽  
Air Gaps ◽  
Body Armour ◽  
Ballistic Protection ◽  
Back Face ◽  
Full Metal Jacket

IntroductionBody armour typically comprises a fabric garment covering the torso combined with hard armour (ceramic/composite). Some users wear only soft armour which provides protection from sharp weapons and pistol ammunition. It is usually recommended that body armour is worn against the body with no air-gaps being present between the wearer and the armour. However, air-gaps can occur in certain situations such as females around the breasts, in badly fitting armour and where manufacturers have incorporated an air-gap claiming improvements in thermophysiological burden. The effect of an air-gap on the ballistic protection and the back face signature (BFS) as a result of a non-perforating ballistic impact was determined.MethodsArmour panels representative of typical police armour (400x400 mm) were mounted on calibrated Roma Plastilina No 1 and impacted with 9 mm Luger FMJ (9×19 mm; full metal jacket; Dynamit Nobel DM11A1B2) ammunition at 365±10 m/s with a range of air-gaps (0–15 mm). Whether or not the ammunition perforated the armour was noted, the BFS was measured and the incidence of pencilling (a severe, deep and narrow BFS) was identified.ResultsFor 0° impacts, a critical air-gap size of 10 mm is detrimental to armour performance for the armour/ammunition combination assessed in this work. Specifically, the incidences of pencilling were more common with a 10 mm air-gap and resulted in BFS depth:volume ratios ≥1.0. For impacts at 30° the armour was susceptible to perforation irrespective of air-gap.ConclusionsThis work suggested that an air-gap behind police body armour might result in an increased likelihood of injury. It is recommended that body armour is worn with no air-gap underneath.

Fasteners at Low Temperatures: Characterization and Methods for Design

2011 ◽  
Author(s):  
Melanie Stephan ◽  
Jens O. Weber ◽  
Ulrich Wuttke ◽  
Christina Berger
Keyword(s):  
Impact Test ◽  
Freezing Point ◽  
Lattice Structure ◽  
Detailed Examination ◽  
Test Methods ◽  
Climatic Conditions ◽  
Test Method ◽  
Design Concepts ◽  
Ductile Behavior ◽  
Pendulum Impact

Bolted joints are a major part of wind energy plants. Due to climatic conditions, they are often exposed to temperatures far below the freezing point. Together with the multiaxial state of stress, which results from the notch effect of the thread, and possible dynamic overloads during operation, sufficient ductility of the material is needed. The state of the art method to investigate the ductile behavior of fasteners is the Charpy pendulum impact test with a V-notched specimen. According to international standard DIN EN ISO 898-1 [1] respectively ASTM F568M-07 [2], fasteners made of carbon steel and alloy steel with a body centered cubic lattice structure can be used for temperatures down to 223 K (−50°C, −58°F) as long as a minimum impact energy of 27 J at 253 K (−20°C, −4°F) is met. As there are several disadvantages in using this test method for fasteners, a detailed examination of existing test methods and design concepts is necessary to find alternatives to the Charpy pendulum impact test. Extensive quasi-static and dynamic material tests were conducted on fasteners with property classes 5.6, 10.9 and 12.9 in a temperature range between 203 K (−70°C, −94°F) and room temperature 293 K (20°C, 68°F). Both mechanical properties and the influence of different specimen geometries were evaluated. Analytical concepts for the description of the low temperature applicability of different steels were analyzed.

scholarly journals Effect of sowing density and nitrogen top-dress fertilisation on growth and yield of chia (Salvia hispanica L.) in a Mediterranean environment: first results

2015 ◽  
Vol 10 (3) ◽  
pp. 163 ◽  
Author(s):  
Rocco Bochicchio ◽  
Roberta Rossi ◽  
Rosanna Labella ◽  
Giovanni Bitella ◽  
Michele Perniola ◽  
...  
Keyword(s):  
Southern Italy ◽  
Plant Density ◽  
Fruit Production ◽  
Growth And Yield ◽  
Leaf Production ◽  
Salvia Hispanica ◽  
Area Index ◽  
First Results ◽  
Salvia Hispanica L ◽  
Set Up

The demand for sources of nutraceuticals has led to the rediscovery and diffusion of traditional crops such as chia (<em>Salvia hispanica</em> L.), whose leaves and fruits are rich in W3 fatty acids and anti-oxidants. Chia originates in Central America but it is rapidly expanding to new areas. A field experiment conducted at Atella in Basilicata (Southern Italy) was set up to test the response of chia to N top-dress fertilisation (0 and 20 kg ha<sup>–1</sup>) and to sowing density (D1=125, D2=25, D3=8 and D4=4 plants m<sup>–2</sup>) in a split-plot design with three replications. First results show maximum leaf area index values up to 7.1 and fresh vegetative biomass production at early flowering ranging between 50.87 (D4) and 59.71 (D1) t ha<sup>–1</sup>. Yield increased with plant density: a significantly (P&lt;0.01) higher production (398 kg ha<sup>–1</sup>) was reached in D1. N top-dressing had a detrimental effect on yield and corresponded to higher lodging and lower maturation percentage of seeds, though non-significant. Based on our first results it seems worthwhile to continue agronomical trials for chia in herbaceous systems of southern Italy for leaf production based on traditional genotypes, while fruit production might be pursued by adopting high sowing density and the search for longer-day genotypes.

scholarly journals FIRST STEPS TOWARDS AN INTEGRATED CITYGML-BASED 3D MODEL OF VIENNA

2016 ◽  
Vol III-4 ◽  
pp. 139-146 ◽  
Author(s):  
G. Agugiaro
Keyword(s):  
Energy Use ◽  
Smart Cities ◽  
Three Dimensional ◽  
3D City Model ◽  
First Results ◽  
Sustainable Energy Systems ◽  
City Model ◽  
Set Up ◽  
The City ◽  
City Models

This paper presents and discusses the results regarding the initial steps (selection, analysis, preparation and eventual integration of a number of datasets) for the creation of an integrated, semantic, three-dimensional, and CityGML-based virtual model of the city of Vienna. CityGML is an international standard conceived specifically as information and data model for semantic city models at urban and territorial scale. It is being adopted by more and more cities all over the world. &lt;br&gt;&lt;br&gt; The work described in this paper is embedded within the European Marie-Curie ITN project “Ci-nergy, Smart cities with sustainable energy systems”, which aims, among the rest, at developing urban decision making and operational optimisation software tools to minimise non-renewable energy use in cities. Given the scope and scale of the project, it is therefore vital to set up a common, unique and spatio-semantically coherent urban model to be used as information hub for all applications being developed. This paper reports about the experiences done so far, it describes the test area and the available data sources, it shows and exemplifies the data integration issues, the strategies developed to solve them in order to obtain the integrated 3D city model. The first results as well as some comments about their quality and limitations are presented, together with the discussion regarding the next steps and some planned improvements.

scholarly journals Improving Interior Environmental Quality Using Sustainable Design in Jordanian Hospital Bedrooms

2020 ◽  
Vol 9 (3) ◽  
pp. 443
Author(s):  
Saeed Hussein Alhmoud ◽  
Çiğdem Çağnan ◽  
Enis Faik Arcan
Keyword(s):  
Interior Design ◽  
Environmental Quality ◽  
Sustainable Design ◽  
Health Sector ◽  
Green Building ◽  
Climatic Conditions ◽  
Building Assessment ◽  
The World ◽  
Set Up ◽  
The One

As the wave of sustainability is sweeping across the major countries and cities of the world, the effect of the inevitable change is finding its way through to the health sector as well. Since the main functions of the hospital include healing the patient, it aims to provide adequate health services to people. Hospitals managers should strive to realize facilities that meet a certain level of demand. This study aims to present the interior environmental quality (IEQ) of bedrooms in Jordanian hospitals and propose a solution to improve indoor environment quality using sustainable design principles. A qualitative research methodology is used in this study. A comparative analysis is made between the original set up of the hospital buildings and the present conditions in which they are in. During the research, it was found that the design to be applied for a hospital should be following the healing environmental characteristics. Besides, the design of hospitals should be made with the climatic conditions of the area in mind. In the advanced countries of the world, hospitals are generally built with extensive research and important factors such as temperature, wind direction and humidity are taken into consideration. The design for a hospital building should be assessed according to the German Green Building Assessment (DGNB) criteria. It has been found that the one-bedroom is ideal for patients because it provides the necessary privacy and also greatly reduces the spread of the disease. In hygienic practices, there should be a first-class healing environment with evidence-based medical research. It was concluded that the practices involving the use of sustainable designs can be followed with the hints received from hospitals in the advanced countries of the world. Keywords: Jordan hospital; IEQ; bedroom; interior design; healthcare; green building assessment; DGNB

scholarly journals The Behavior of Wheat Varieties to Attack By Fusarium Spp. in Different Test

2012 ◽  
Vol 69 (1) ◽  
Author(s):  
Laura Maria ȘOPTEREAN ◽  
Alexandra SUCIU ◽  
Elena NAGY
Keyword(s):  
Statistical Processing ◽  
Grain Protein Content ◽  
Test Methods ◽  
Climatic Conditions ◽  
Cereal Crops ◽  
Fusarium Spp ◽  
Wheat Varieties ◽  
Significant Damage ◽  
Test Version ◽  
Qualitative Nature

Fusarium  is one of the most widespread and damaging diseases of cereal crops (wheat, barley, rye), mainly due to the attack on the ears. In favorable areas for Fusarium , attack causes significant damage in terms of quantity, as a result of reducing the number of berries and THGW's decline, and loss of a qualitative nature, due to lower grain protein content and mycotoxins occurrence. The yield losses caused by Fusarium in wheat, varies from year to year, mainly driven by climatic conditions and technological, source of inoculum and cultivated variety. The objective of this paper was to determine the reaction of wheat varieties to the attack by Fusarium spp. in different test conditions. The researches took place in ARDS Turda, in the Laboratory of Phytopathology. The experiments were located by randomized block method in three replications. Biological material was represented by three varieties of wheat, developed by the Laboratory of Wheat Improvement. Test methods were: uninoculated-untreated, inoculated-untreated, inoculated-treated and uninoculatedtreated. The inoculation was done with the suspension of Fusarium spp. and treatments were applied with products: Falcon 250 EC and Prosaro 460 EC. The manifestation degree of Fusarium was expressed as the percentage of ears and grains infected, and production was expressed by t / ha. After observations and statistical processing of data we can say that the percentage of infected grain varies between 0-16 %, for varieties studied. Yield obtained have been affected by the test version in the two experimental years, the lowest yields were obtained in natural and artificial infection, but without treatment, ranging between 4.7 to 4.9 t / ha in 2010 and 2.8 to 3.9 in 2011.

scholarly journals PENGEMBANGAN WIKI KAMPUS SEBAGAI MEDIA PENGETAHUAN KOMUNITAS DI PERPUSTAKAAN PERGURUAN TINGGI

2017 ◽  
Vol 5 (1) ◽  
pp. 29
Author(s):  
Abdurrakhman Prasetyadi ◽  
Danang Dwijo Kangko ◽  
D.W. Ari Nugroho
Keyword(s):  
Data Flow ◽  
Flow Diagram ◽  
Web Content ◽  
Knowledge Communities ◽  
University Library ◽  
First Results ◽  
Data Flow Diagram ◽  
Online Encyclopedia ◽  
Set Up ◽  
The University

<p>This study aims to: (1) create category of knowledge communities in university library, (2) designing the prototype of an online encyclopedia of knowledge communities in the university library, and (3) testing a prototype of an online encyclopedia of knowledge communities. The method used is the analysis of web content of the communities website at IPB and development protoype using the MediaWiki software. The first results of this study are categories of knowledge created consisting of the main knowledge about the student association, student activity units, other communities, the terms of the campus and the surrounding of the campus. Second, in designing a prototype of Wiki Kampus make a data flow diagrams, system infrastructure, and installation. Furthermore, installation of MediaWiki including by several stages: (1) downloading and extracting the file master MediaWiki on a web server, (2) set-up the master files MediaWiki, (3) determine the format page categorizing and customize the user interface, and (4) set up a user account for students. Third, Wiki Kampus tested by some students of Master of Information Technology for Libraries (MTP) at IPB and the results is function well.</p><p>Kajian ini bertujuan untuk: (1) membuat kategori pengetahuan komunitas di perpusatakaan PT, (2) merancang prototipe ensiklopedia daring pengetahuan komunitas di perpustakaan PT, dan (3) melakukan ujicoba prototipe ensiklopedia daring pengetahuan komunitas. Metode yang digunakan yaitu analisis konten web komunitas di IPB dan pengembangan prototipe Wiki Kampus menggunakan perangkat lunak MediaWiki. Hasil dari kajian ini yaitu kategori pengetahuan yang dibuat terdiri dari pengetahuan utama yakni seputar himpunan mahasiswa, unit kegiatan mahasiswa, komunitas lain, istilah-istilah kampus dan lingkungan sekitar kampus. Hasil perancangan prototipe Wiki Kampus terdiri dari pembuatan <em>data flow diagram</em>, perencanaan infrastruktur sistem dan penginstalasian perangkat lunak MediaWiki. Penginstalasian MediaWiki melalui beberapa tahapan di antaranya: (1) mengunduh dan mengekstraksi file master MediaWiki pada server web, (2) melakukan <em>set-up</em> file master MediaWiki, (3) menentukan format <em>page categorizing</em> dan mengkustomisasi tampilan pengguna, serta (4) menyiapkan <em>user account</em> untuk mahasiswa. Ketiga, ujicoba Wiki Kampus dilakukan oleh beberapa mahasiswa program Magister Teknologi Informasi untuk Perpustakaan (MTP) IPB berjalan lancar dan berfungsi dengan baik.</p>

Sign in / Sign up

Export Citation Format

Share Document