scholarly journals Asbestos-Free Aluminium Dross Brake Pad: A Mini Review

2021 ◽  
Vol 1107 (1) ◽  
pp. 012034
Author(s):  
J.O. Dirisu ◽  
O.S.I. Fayomi ◽  
S.O Oyedepo ◽  
N. E Udoye
Keyword(s):  
Brake Pad ◽  
Aluminium Dross

BaSO4-Friction Dust Filler Improves Friction Characteristic in Non-Asbestos Brake Pad Composite

2019 ◽  
Vol 13 (9) ◽  
pp. 513
Author(s):  
Putri Nawangsari ◽  
Jamasri Jamasri ◽  
Heru Santoso Budi Rochardjo ◽  
Arif Tri Waskito
Keyword(s):  
Brake Pad ◽  
Friction Characteristic

Production of Asbestos-free Brake Pad Using Groundnut Shell as Filler Material

2018 ◽  
Vol 4 (12) ◽  
Author(s):  
W. C. Solomon ◽  
M. T. Lilly ◽  
J. I. Sodiki
Keyword(s):  
Phenolic Resin ◽  
Cost Effective ◽  
Filler Material ◽  
Particle Sizes ◽  
Brake Pad ◽  
Brake Pads ◽  
Environmental Friendly ◽  
Sieve Size ◽  
Groundnut Shell ◽  
The Cost

The development and evaluation of brake pads using groundnut shell (GS) particles as substitute material for asbestos were carried out in this study. This was with a view to harnessing the properties of GS, which is largely deposited as waste, and in replacing asbestos which is carcinogenic in nature despite its good tribological and mechanical properties. Two sets of composite material were developed using varying particle sizes of GS as filler material, with phenolic resin as binder with percentage compositions of 45% and 50% respectively. Results obtained indicate that the compressive strength and density increase as the sieve size of the filler material decreases, while water and oil absorption rates increase with an increase in sieve size of GS particle. This study also indicates that the cost of producing brake pad can be reduced by 19.14 percent if GS is use as filler material in producing brake pad. The results when compared with those of asbestos and industrial waste showed that GS particle can be used as an effective replacement for asbestos in producing automobile brake pad. Unlike asbestos, GS-based brake pads are environmental friendly, biodegradable and cost effective.

Tribological and dynamical analysis of a brake pad with multiple blocks for a high-speed train

2019 ◽  
Vol 234 (11) ◽  
pp. 1771-1788
Author(s):  
YK Wu ◽  
JL Mo ◽  
B Tang ◽  
JW Xu ◽  
B Huang ◽  
...  
Keyword(s):  
High Speed ◽  
Wear Behavior ◽  
Dynamical Analysis ◽  
Brake Disc ◽  
Brake Pad ◽  
High Speed Train ◽  
Brake Squeal ◽  
Element Analysis ◽  
Single Block ◽  
Middle Ring

In this research, the tribological and dynamical characteristics of a brake pad with multiple blocks are investigated using experimental and numerical methods. A dynamometer with a multiblock brake pad configuration on a brake disc is developed and a series of drag-type tests are conducted to study the brake squeal and wear behavior of a high-speed train brake system. Finite element analysis is performed to derive physical explanations for the observed experimental phenomena. The experimental and numerical results show that the rotational speed and braking force have important influences on the brake squeal; the trends of the multiblock and single-block systems are different. In the multiblock brake pad, the different blocks exhibit significantly different magnitudes of contact stresses and vibration accelerations. The blocks located in the inner and outer rings have higher vibration acceleration amplitudes and stronger vibration energies than the blocks located in the middle ring.

Optimization of Organic Fibres%[Kevlar/Arobocel/Acrylic] in NAO Brake Pad Application and its Effect on Thermal Stability & Friction Characteristics

2012 ◽  
Vol 531-532 ◽  
pp. 8-12
Author(s):  
M.A. Sai Balaji ◽  
K. Kalaichelvan
Keyword(s):  
Thermal Stability ◽  
Weight Loss ◽  
Minimum Weight ◽  
Friction Material ◽  
Brake Pad ◽  
Temperature Zone ◽  
Good Thermal Stability ◽  
Friction Testing ◽  
Brake Application ◽  
The Stability

Organic fibres (Kevlar/ Arbocel / Acrylic) have good thermal stability, higher surface area and bulk density. The optimization of organic fibres percentage for thermal behaviour is considered using TGA. The temperature raise during brake application will be between 150-4000 C and this temperature zone is very critical to determine the fade characteristics during friction testing. Hence, three different friction composites are developed with the same formulation varying only the Kevlar, Arbocel and Acrylic fibres which are compensated by the inert filler namely the barites and are designated as NA01, NA02 and NA03 respectively. After the fabrication, the TGA test reveals that the composite NA03 has minimum weight loss. The friction coefficient test rig is then used to test the friction material as per SAE J661a standards. The results prove that the brake pad with minimum weight loss during TGA has higher friction stability. Thus, we can correlate the thermal stability with the stability of friction.

Numerical Modeling and Simulation Analysis of Temperature Field of Disc Brake on Trains

2011 ◽  
Vol 199-200 ◽  
pp. 1492-1495 ◽  
Author(s):  
Guo Shun Wang ◽  
Rong Fu ◽  
Liang Zhao
Keyword(s):  
Temperature Field ◽  
Temperature Gradient ◽  
High Speed ◽  
Large Scale ◽  
Working Condition ◽  
Constant Speed ◽  
Brake Disc ◽  
Disc Brake ◽  
Brake Pad ◽  
Finite Element Software

The simulation calculation on the temperature field of the disc brake system on high-speed trains under the working condition of constant speed at 50Km/h is made. A steady-state calculation model is established according to the actual geometric size of a brake disc and a brake pad, and the analog calculation and simulation on the temperature field of the brake disc and the brake pad by using the large-scale nonlinear finite element software ABAQUS are carried out. The distribution rules of the temperature field of the brake disc and the brake pad under the working condition of constant speed are made known. The surface temperature of the brake disc at friction radius is the highest, with a band distribution for temperature. There exists a temperature flex point in the direction of thickness, of which the thickness occupies 15% of that of the brake disc; due to the small volume of the brake pad, the temperature gradient of the whole brake pad is not sharp, and larger temperature gradient occurs only on the contact surface.

scholarly journals Sensitivity study of the contact situation between the brake pad and the disc

PAMM ◽  
2011 ◽  
Vol 11 (1) ◽  
pp. 205-206
Author(s):  
Dominika Dombek ◽  
Georg-Peter Ostermeyer
Keyword(s):  
Sensitivity Study ◽  
Brake Pad ◽  
Contact Situation
Sign in / Sign up

Export Citation Format

Share Document