scholarly journals A quad-stable piezoelectric energy harvester for enhancing energy harvesting from rotational motion: Theoretical model and experiments

2019 ◽  
Vol 531 ◽  
pp. 012010
Author(s):  
Xutao Mei ◽  
Shengxi Zhou ◽  
Zhichun Yang ◽  
Tsutomu Kaizuka ◽  
Kimihiko Nakano
Keyword(s):  
Theoretical Model ◽  
Energy Harvesting ◽  
Rotational Motion ◽  
Energy Harvester ◽  
Piezoelectric Energy

scholarly journals Analysis of a Cantilevered Piezoelectric Energy Harvester in Different Orientations for Rotational Motion

Sensors ◽  
2020 ◽  
Vol 20 (4) ◽  
pp. 1206 ◽  
Author(s):  
Wei-Jiun Su ◽  
Jia-Han Lin ◽  
Wei-Chang Li
Keyword(s):  
Theoretical Model ◽  
Resonant Frequency ◽  
Rotational Motion ◽  
Axial Load ◽  
Energy Harvester ◽  
Excitation Frequency ◽  
Experimental Studies ◽  
Piezoelectric Energy ◽  
Piezoelectric Cantilever ◽  
Tip Mass

This paper investigates a piezoelectric energy harvester that consists of a piezoelectric cantilever and a tip mass for horizontal rotational motion. Rotational motion results in centrifugal force, which causes the axial load on the beam and alters the resonant frequency of the system. The piezoelectric energy harvester is installed on a rotational hub in three orientations—inward, outward, and tilted configurations—to examine their influence on the performance of the harvester. The theoretical model of the piezoelectric energy harvester is developed to explain the dynamics of the system and experiments are conducted to validate the model. Theoretical and experimental studies are presented with various tilt angles and distances between the harvester and the rotating center. The results show that the installation distance and the tilt angle can be used to adjust the resonant frequency of the system to match the excitation frequency.

scholarly journals Piezoelectric Impact Energy Harvester Based on the Composite Spherical Particle Chain for Self-Powered Sensors

Sensors ◽  
2021 ◽  
Vol 21 (9) ◽  
pp. 3151
Author(s):  
Shuo Yang ◽  
Bin Wu ◽  
Xiucheng Liu ◽  
Mingzhi Li ◽  
Heying Wang ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Spherical Particle ◽  
Impact Energy ◽  
Energy Harvester ◽  
Composite Particle ◽  
Piezoelectric Energy Harvesting ◽  
Particle Chain ◽  
Piezoelectric Energy ◽  
Self Powered ◽  
Particle Chains

In this study, a novel piezoelectric energy harvester (PEH) based on the array composite spherical particle chain was constructed and explored in detail through simulation and experimental verification. The power test of the PEH based on array composite particle chains in the self-powered system was realized. Firstly, the model of PEH based on the composite spherical particle chain was constructed to theoretically realize the collection, transformation, and storage of impact energy, and the advantages of a composite particle chain in the field of piezoelectric energy harvesting were verified. Secondly, an experimental system was established to test the performance of the PEH, including the stability of the system under a continuous impact load, the power adjustment under different resistances, and the influence of the number of particle chains on the energy harvesting efficiency. Finally, a self-powered supply system was established with the PEH composed of three composite particle chains to realize the power supply of the microelectronic components. This paper presents a method of collecting impact energy based on particle chain structure, and lays an experimental foundation for the application of a composite particle chain in the field of piezoelectric energy harvesting.

Optimization of energy harvesting based on the uniform deformation of piezoelectric ceramic

2016 ◽  
Vol 09 (05) ◽  
pp. 1650069 ◽  
Author(s):  
Yaoze Liu ◽  
Tongqing Yang ◽  
Fangming Shu
Keyword(s):  
Energy Harvesting ◽  
Power Output ◽  
Piezoelectric Ceramic ◽  
Energy Harvester ◽  
Optimization Method ◽  
Piezoelectric Energy ◽  
Bonding Area ◽  
Almost All ◽  
Matching Load ◽  
Tip Mass

Since the piezoelectric properties were used for energy harvesting, almost all forms of energy harvester needs to be bonded with a mass block to achieve pre-stress. In this article, disc type piezoelectric energy harvester is chosen as the research object and the relationship between mass bonding area and power output is studied. It is found that if the bonding area is changed as curved, which is usually complanate in previous studies, the deformation of the circular piezoelectric ceramic is more uniform and the power output is enhanced. In order to test the change of the deformation, we spray several homocentric annular electrodes on the surface of a piece of bare piezoelectric ceramic and the output of each electrode is tested. Through this optimization method, the power output is enhanced to more than 11[Formula: see text]mW for a matching load about 24[Formula: see text]k[Formula: see text] and a tip mass of 30[Formula: see text]g at its resonant frequency of 139[Formula: see text]Hz.

Magnetic plucked meso-scale piezoelectric energy harvester for low-frequency rotational motion

2021 ◽  
Author(s):  
Chao-Ting Chen ◽  
Wei-Jiun Su ◽  
Wen-Jong Wu ◽  
dejan vasic ◽  
François Costa
Keyword(s):  
Rotational Motion ◽  
Energy Harvester ◽  
Low Frequency ◽  
Piezoelectric Energy ◽  
Meso Scale

Energy Harvesting Characteristics from Water Flow by Piezoelectric Energy Harvester Device Using Cr/Nb Doped Pb(Zr,Ti)O3Bimorph Cantilever

2013 ◽  
Vol 52 (10S) ◽  
pp. 10MB01 ◽  
Author(s):  
Kyoung-Bum Kim ◽  
Chang Il Kim ◽  
Young Hun Jeong ◽  
Jeong-Ho Cho ◽  
Jong-Hoo Paik ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Water Flow ◽  
Energy Harvester ◽  
Piezoelectric Energy

scholarly journals Modeling and Experiment of a V-Shaped Piezoelectric Energy Harvester

2018 ◽  
Vol 2018 ◽  
pp. 1-15 ◽  
Author(s):  
Yue Zhao ◽  
Yi Qin ◽  
Lei Guo ◽  
Baoping Tang
Keyword(s):  
Energy Harvesting ◽  
Frequency Band ◽  
Electromechanical Coupling ◽  
Energy Harvester ◽  
Structural Parameters ◽  
Ambient Vibration ◽  
Piezoelectric Bimorph ◽  
Actual Structure ◽  
Piezoelectric Energy ◽  
Operation Frequency

Vibration-based energy harvesting technology is the most promising method to solve the problems of self-powered wireless sensor nodes, but most of the vibration-based energy harvesters have a rather narrow operation bandwidth and the operation frequency band is not convenient to adjust when the ambient frequency changes. Since the ambient vibration may be broadband and changeable, a novel V-shaped vibration energy harvester based on the conventional piezoelectric bimorph cantilevered structure is proposed, which successfully improves the energy harvesting efficiency and provides a way to adjust the operation frequency band of the energy harvester conveniently. The electromechanical coupling equations are established by using Euler-Bernoulli equation and piezoelectric equation, and then the coupled circuit equation is derived based on the series connected piezoelectric cantilevers and Kirchhoff's laws. With the above equations, the output performances of V-shaped structure under different structural parameters and load resistances are simulated and discussed. Finally, by changing the angle θ between two piezoelectric bimorph beams and the load resistance, various comprehensive experiments are carried out to test the performance of this V-shaped energy harvester under the same excitation. The experimental results show that the V-shaped energy harvester can not only improve the frequency response characteristic and the output performance of the electrical energy, but also conveniently tune the operation bandwidth; thus it has great application potential in actual structure health monitoring under variable working condition.

Broadband Rotational Energy Harvesting Using Micro Energy Harvester

2018 ◽  
Author(s):  
Jui-Ta Chien ◽  
Yung-Hsing Fu ◽  
Chao-Ting Chen ◽  
Shun-Chiu Lin ◽  
Yi-Chung Shu ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Voltage ◽  
Energy Harvester ◽  
Low Frequency ◽  
Rotational Energy ◽  
Open Circuit ◽  
Maximum Output ◽  
Rotational Excitation ◽  
Rotating Speed ◽  
Piezoelectric Energy

This paper proposes a broadband rotational energy harvesting setup by using micro piezoelectric energy harvester (PEH). When driven in different rotating speed, the PEH can output relatively high power which exhibits the phenomenon of frequency up-conversion transforming the low frequency of rotation into the high frequency of resonant vibration. It aims to power self-powered devices used in the applications, like smart tires, smart bearings, and health monitoring sensors on rotational machines. Through the excitation of the rotary magnetic repulsion, the cantilever beam presents periodically damped oscillation. Under the rotational excitation, the maximum output voltage and power of PEH with optimal impedance is 28.2 Vpp and 663 μW, respectively. The output performance of the same energy harvester driven in ordinary vibrational based excitation is compared with rotational oscillation under open circuit condition. The maximum output voltage under 2.5g acceleration level of vibration is 27.54 Vpp while the peak output voltage of 36.5 Vpp in rotational excitation (in 265 rpm).

scholarly journals Piezoelectric Energy Harvesting with an Ultrasonic Vibration Source

Actuators ◽  
2019 ◽  
Vol 8 (1) ◽  
pp. 8
Author(s):  
Tao Li ◽  
Pooi Lee
Keyword(s):  
Energy Harvesting ◽  
High Power ◽  
High Frequency ◽  
Energy Harvester ◽  
Impedance Matching ◽  
Low Frequency ◽  
Vibration Source ◽  
Piezoelectric Energy ◽  
Power Ultrasonic ◽  
Ultrasonic Cutting

A piezoelectric energy harvester was developed in this paper. It is actuated by the vibration leakage from the nodal position of a high-power ultrasonic cutting transducer. The harvester was excited at a low displacement amplitude (0.73 µmpp). However, its operation frequency is quite high and reaches the ultrasonic range (24.4 kHz). Compared with another low frequency harvester (66 Hz), both theoretical and experimental results proved that the advantages of this high frequency harvester include (i) high current generation capability (up to 20 mApp compared to 1.3 mApp of the 66 Hz transducer) and (ii) low impedance matching resistance (500 Ω in contrast to 50 kΩ of the 66 Hz transducer). This energy harvester can be applied either in sensing, or vibration controlling, or simply energy harvesting in a high-power ultrasonic system.

scholarly journals FINITE ELEMENT SIMULATION OF MEMS PIEZOELECTRIC ENERGY SCAVENGER BASED ON PZT THIN FILM

2019 ◽  
Vol 20 (1) ◽  
pp. 90-99
Author(s):  
Aliza Aini Md Ralib ◽  
Nur Wafa Asyiqin Zulfakher ◽  
Rosminazuin Ab Rahim ◽  
Nor Farahidah Za'bah ◽  
Noor Hazrin Hany Mohamad Hanif
Keyword(s):  
Thin Film ◽  
Energy Harvesting ◽  
Output Voltage ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Vibration Energy ◽  
Maximum Output ◽  
Vibration Energy Harvesting ◽  
Piezoelectric Energy ◽  
The World

Vibration energy harvesting has been progressively developed in the advancement of technology and widely used by a lot of researchers around the world. There is a very high demand for energy scavenging around the world due to it being cheaper in price, possibly miniaturized within a system, long lasting, and environmentally friendly. The conventional battery is hazardous to the environment and has a shorter operating lifespan. Therefore, ambient vibration energy serves as an alternative that can replace the battery because it can be integrated and compatible to micro-electromechanical systems. This paper presents the design and analysis of a MEMS piezoelectric energy harvester, which is a vibration energy harvesting type. The energy harvester was formed using Lead Zicronate Titanate (PZT-5A) as the piezoelectric thin film, silicon as the substrate layer and structural steel as the electrode layer. The resonance frequency will provide the maximum output power, maximum output voltage and maximum displacement of vibration. The operating mode also plays an important role to generate larger output voltage with less displacement of cantilever. Some designs also have been studied by varying height and length of piezoelectric materials. Hence, this project will demonstrate the simulation of a MEMS piezoelectric device for a low power electronic performance. Simulation results show PZT-5A piezoelectric energy with a length of 31 mm and height of 0.16 mm generates maximum output voltage of 7.435 V and maximum output power of 2.30 mW at the resonance frequency of 40 Hz. ABSTRAK: Penuaian tenaga getaran telah berkembang secara pesat dalam kemajuan teknologi dan telah digunakan secara meluas oleh ramai penyelidik di seluruh dunia. Terdapat permintaan yang sangat tinggi di seluruh dunia terhadap penuaian tenaga kerana harganya yang lebih murah, bersaiz kecil dalam satu sistem, tahan lama dan mesra alam. Manakala, bateri konvensional adalah berbahaya bagi alam sekitar dan mempunyai jangka hayat yang lebih pendek. Oleh itu, getaran tenaga dari persekitaran lebih sesuai sebagai alternatif kepada bateri kerana ia mudah diintegrasikan dan serasi dengan sistem mikroelektromekanikal. Kertas kerja ini  membentangkan reka bentuk dan analisis tenaga piezoelektrik MEMS iaitu salah satu jenis penuaian tenaga getaran. Penuai tenaga ini dibentuk menggunakan Lead Zicronate Titanate (PZT-5A) sebagai lapisan filem tipis piezoelektrik, silikon sebagai lapisan substrat dan keluli struktur sebagai lapisan elektrod. Frekuensi resonans akan memberikan hasil tenaga maksima, voltan tenaga maksima dan getaran jarak maksima. Mod pengendalian juga memainkan peranan penting bagi menghasilkan tenaga yang lebih besar. Reka bentuk yang mempunyai ketinggian dan panjang berlainan juga telah diuji dengan menggunakan bahan piezoelektrik yang sama. Oleh itu, projek ini akan menghasilkan simulasi piezoelektrik MEMS yang sesuai digunakan bagi alat elektronik berkuasa rendah. Hasil simulasi menunjukkan dengan panjang 31 mm dan ketinggian 0.16 mm, piezoelektrik PZT ini menghasilkan voltan maksima sebanyak 7.435 V dan tenaga output maksima 2.30 mW pada frekuensi resonans 40 Hz.

Sign in / Sign up

Export Citation Format

Share Document