DIELECTRIC PROPERTIES OF POLY (VINYLIDENE FLUORIDE)/BARIUM TITANATE NANOCOMPOSITES UNDER GAMMA IRRADIATION

2019 ◽  
Vol 184 (3-4) ◽  
pp. 342-346
Author(s):  
K Waree ◽  
K Pangza ◽  
N Jangsawang ◽  
P Thongbai ◽  
S Buranurak
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Gamma Irradiation ◽  
Nanocomposite Film ◽  
Gamma Ray ◽  
Vinylidene Fluoride ◽  
Volume Fraction ◽  
Composite Films ◽  
Significant Difference ◽  
Accumulated Dose

Abstract The main focus of this study is to investigate the effect of gamma irradiation on the electrical properties of PVDF/BT nanocomposites. A 1.25 MeV gamma-ray was delivered to the composite films with different BaTiO3-volume fraction, ƒBT = 0–0.4, and with different absorbed doses ranged 50–2500 Gy. Dielectric properties of PVDF/BaTiO3 composites under frequencies ranged from 100 Hz to 10 MHz at room temperature were investigated using an impedance analyser. An increase of 28% in the dielectric constant and a decrease of 15% in the loss tangent were observed in the PVDF/BT 40 vol% nanocomposite film under the accumulated dose of 1500 Gy. Scanning electron microscopy provided no significant difference in microscopic structures between non-exposed and gamma-exposed materials. Fourier-transform infra-red spectroscopy provides gamma-induced transition of PVDF-crystalline forms as alpha-PVDF into beta-PVDF/gamma-PVDF which has been reported as one of the main factors affected the change of dielectric constant in polymers. UV–visible spectrophotometry has been observed gamma-induced red shift in the absorption edge of the PVDF/BT 40 vol% nanocomposite film from 400 nm to 420 nm under the accumulated dose of 1500 Gy. However, a blue shift is observed with increase the accumulated dose up to 2000 Gy.

Preparation, Morphology and Dielectric Properties of Polyamide-6/Poly(Vinylidene Fluoride) Blends

2012 ◽  
Vol 496 ◽  
pp. 263-267
Author(s):  
Rui Li ◽  
Jian Zhong Pei ◽  
Yan Wei Li ◽  
Xin Shi ◽  
Qun Le Du
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Flexible Electronics ◽  
High Dielectric Constant ◽  
Vinylidene Fluoride ◽  
Volume Fraction ◽  
Polyamide 6 ◽  
Dielectric Constants ◽  
Poly Vinylidene Fluoride ◽  
High Dielectric

A novel all-polymeric material with high dielectric constant (k) has been developed by blending poly (vinylidene fluoride) (PVDF) with polyamide-6 (PA6). The dependence of the dielectric properties on frequency and polymer volume fraction was investigated. When the volume fraction of PA6 is 20%, the dielectric property is better than others. The SEM investigations suggest that the enhanced dielectric behavior originates from significant interfacial interactions of polymer-polymer. The XRD demonstrate that the PA6 and PVDF affect the crystalline behavior of each component. Furthermore, the stable dielectric constants of the blends could be tuned by adjusting the content of the polymers. The created high-k all-polymeric blends represent a novel type of material that are simple technology and easy to process, and is of relatively high dielectric constant, applications as flexible electronics.

Preparation and Dielectric Properties of Cu/PVDF Composite Films

2014 ◽  
Vol 1035 ◽  
pp. 417-421 ◽  
Author(s):  
Jian Wen Zhai ◽  
Ya Jun Wang ◽  
Jian Lou Deng ◽  
Chang Gen Feng
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Room Temperature ◽  
Volume Fraction ◽  
Composite Films ◽  
Interfacial Polarization ◽  
Dielectric Constants ◽  
Pvdf Film ◽  
Continuous Increase ◽  
Better Than

nanoand micro size Cu were employed separately and investigated comparatively. Different volume fraction of Cu was added into PVDF film in order to investigate the content of filler effect on the dielectric properties of polymer composites. XRD and SEM were used to analyze the crystalline phase and microstructure of the films. The results show that two sizes of Cu have the same peak features, and with the continuous increase of the content of Cu, it disperse better in PVDF. The dielectric constant (ε) of the composite containing 16 vol% micro-CCTO filler is 16 at 100 Hz and room temperature, and its dielectric loss (tanδ) is only 0.15, which is substantially better than others. Besides, for 18 vol% nanoCu/PVDF composite tanδis 0.25 andεis 18 at 100 Hz. Moreover,εand tanδof nanoCu/PVDF composite are both higher than those of micro-Cu/PVDF. Analysis shows that the composites with nanoCu have higher dielectric constants, which is mainly from the interfacial polarization.

scholarly journals Dielectric Properties of P(VDF-TrFE-CTFE) Composites Filled with Surface-Coated TiO2 Nanowires by SnO2 Nanoparticles

Polymers ◽  
2020 ◽  
Vol 12 (1) ◽  
pp. 85 ◽  
Author(s):  
Qilong Zhang ◽  
Zhao Zhang ◽  
Nuoxin Xu ◽  
Hui Yang
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Vinylidene Fluoride ◽  
Volume Fraction ◽  
Sno2 Nanoparticles ◽  
Interfacial Polarization ◽  
Hybrid Structure ◽  
Precipitation Method ◽  
Tio2 Nanowires ◽  
Improved Performance

Nanocomposites containing inorganic fillers embedded in polymer matrices have exhibited great potential applications in capacitors. Therefore, an effective method to improve the dielectric properties of polymer is to design novel fillers with a special microstructure. In this work, a combination of hydrothermal method and precipitation method was used to synthesize in situ SnO2 nanoparticles on the surface of one-dimensional TiO2 nanowires (TiO2 NWs), and the TiO2NWs@SnO2 fillers well-dispersed into the poly (vinylidene fluoride-trifluoroethylene-chlorotrifluoroethylene) [P(VDF-TrFE-CTFE)] polymer. Hybrid structure TiO2NWs @SnO2 introduce extra interfaces, which enhance the interfacial polarization and the dielectric constant. Typically, at 10 vol.% low filling volume fraction, the composite with TiO2NWs @SnO2 shows a dielectric constant of 133.4 at 100 Hz, which is almost four times that of polymer. Besides, the TiO2 NWs prevents the direct contact of SnO2 with each other in the polymer matrix, so the composites still maintain good insulation performance. All the improved performance indicates these composites can be widely useful in electronic devices.

scholarly journals Enhanced Dielectric Performance of P(VDF-HFP) Composites with Satellite–Core-Structured Fe2O3@BaTiO3 Nanofillers

Polymers ◽  
2019 ◽  
Vol 11 (10) ◽  
pp. 1541 ◽  
Author(s):  
Yongchang Jiang ◽  
Zhao Zhang ◽  
Zheng Zhou ◽  
Hui Yang ◽  
Qilong Zhang
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Flexible Electronics ◽  
Vinylidene Fluoride ◽  
Breakdown Strength ◽  
Composite Films ◽  
Interfacial Polarization ◽  
Dielectric Materials ◽  
Dielectric Performance ◽  
High Dielectric

Polymer dielectric materials are extensively used in electronic devices. To enhance the dielectric constant, ceramic fillers with high dielectric constant have been widely introduced into polymer matrices. However, to obtain high permittivity, a large added amount (>50 vol%) is usually needed. With the aim of improving dielectric properties with low filler content, satellite–core-structured Fe2O3@BaTiO3 (Fe2O3@BT) nanoparticles were fabricated as fillers for a poly(vinylidene fluoride-co-hexafluoropropylene) (P(VDF-HFP)) matrix. The interfacial polarization effect is increased by Fe2O3 nanoparticles, and thus, composite permittivity is enhanced. Besides, the satellite–core structure prevents Fe2O3 particles from directly contacting each other, so that the dielectric loss remains relatively low. Typically, with 20 vol% Fe2O3@BT nanoparticle fillers, the permittivity of the composite is 31.7 (1 kHz), nearly 1.8 and 3.0 times that of 20 vol% BT composites and pure polymers, respectively. Nanocomposites also achieve high breakdown strength (>150 KV/mm) and low loss tangent (~0.05). Moreover, the composites exhibited excellent flexibility and maintained good dielectric properties after bending. These results demonstrate that composite films possess broad application prospects in flexible electronics.

scholarly journals Effect of Terminal Groups on Thermomechanical and Dielectric Properties of Silica–Epoxy Composite Modified by Hyperbranched Polyester

Polymers ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2451
Author(s):  
Jianwen Zhang ◽  
Dongwei Wang ◽  
Lujia Wang ◽  
Wanwan Zuo ◽  
Lijun Zhou ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Binding Energy ◽  
Epoxy Resin ◽  
Volume Fraction ◽  
Epoxy Composite ◽  
Mean Square Displacement ◽  
Mean Square ◽  
Hyperbranched Polyester ◽  
Free Volume Fraction

To study the effect of hyperbranched polyester with different kinds of terminal groups on the thermomechanical and dielectric properties of silica–epoxy resin composite, a molecular dynamics simulation method was utilized. Pure epoxy resin and four groups of silica–epoxy resin composites were established, where the silica surface was hydrogenated, grafted with silane coupling agents, and grafted with hyperbranched polyester with terminal carboxyl and terminal hydroxyl, respectively. Then the thermal conductivity, glass transition temperature, elastic modulus, dielectric constant, free volume fraction, mean square displacement, hydrogen bonds, and binding energy of the five models were calculated. The results showed that the hyperbranched polyester significantly improved the thermomechanical and dielectric properties of the silica–epoxy composites compared with other surface treatments, and the terminal groups had an obvious effect on the enhancement effect. Among them, epoxy composite modified by the hyperbranched polyester with terminal carboxy exhibited the best thermomechanical properties and lowest dielectric constant. Our analysis of the microstructure found that the two systems grafted with hyperbranched polyester had a smaller free volume fraction (FFV) and mean square displacement (MSD), and the larger number of hydrogen bonds and greater binding energy, indicating that weaker strength of molecular segments motion and stronger interfacial bonding between silica and epoxy resin matrix were the reasons for the enhancement of the thermomechanical and dielectric properties.

Large d33 and enhanced ferroelectric/dielectric properties of poly(vinylidene fluoride)-based composites filled with Pb(Zr0.52Ti0.48)O3 nanofibers

RSC Advances ◽  
2015 ◽  
Vol 5 (63) ◽  
pp. 51302-51307 ◽  
Author(s):  
Jie Chang ◽  
Yang Shen ◽  
Xiangcheng Chu ◽  
Xuehui Zhang ◽  
Yu Song ◽  
...  
Keyword(s):  
Dielectric Properties ◽  
Vinylidene Fluoride ◽  
Composite Films ◽  
Poly Vinylidene Fluoride

Pb(Zr0.52Ti0.48)O3 (PZT) nanofibers with diameters of 150–200 nm are prepared via electrospinning and used as dielectric fillers in poly(vinylidene fluoride) (PVDF)-based composite films.

scholarly journals Crystallization and Dielectric Properties of MWCNT /Poly(1-Butene) Composite Films by a Solution Casting Method

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 755
Author(s):  
Lingfei Li ◽  
Qiu Sun ◽  
Xiangqun Chen ◽  
Yongjun Xu ◽  
Zhaohua Jiang
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Dielectric Loss ◽  
Breakdown Strength ◽  
Composite Films ◽  
Conductive Filler ◽  
Interfacial Polarization ◽  
Solution Casting ◽  
Casting Method ◽  
Solution Casting Method

In this work, poly(1-butene) (PB-1) composite films with multi-walled carbon nanotubes (MWCNT) were prepared by a solution casting method. The relationship between the dielectric properties and the crystal transformation process of the films was investigated. It was indicated that there were two crystal forms of I and II of PB-1 during the solution crystallization process. With the prolongation of the phase transition time, form II was converted into form I. The addition of the conductive filler (MWCNT) accelerated the rate of phase transformation and changed the nucleation mode of PB-1. The presence of crystal form I in the system increased the breakdown strength and the dielectric constant of the films and reduced the dielectric loss, with better stability. In addition, the dielectric constant and the dielectric loss of the MWCNT/PB-1 composite films increased with the addition of MWCNT, due to the interfacial polarization between MWCNT and PB-1 matrix. When the mass fraction of the MWCNT was 1.0%, the composite film had a dielectric constant of 43.9 at 25 °C and 103 Hz, which was 20 times that of the original film.

Dielectric Properties of Poly(vinylidene fluoride)/PMN-PT Composite Films for Embedded Capacitors

2015 ◽  
Vol 7 (9) ◽  
pp. 776-781 ◽  
Author(s):  
A. K. Batra ◽  
Almuatasim Alomari ◽  
Mary McDaniel ◽  
Kyana McKay ◽  
Marylyn Creer
Keyword(s):  
Dielectric Properties ◽  
Vinylidene Fluoride ◽  
Composite Films ◽  
Embedded Capacitors ◽  
Poly Vinylidene Fluoride

scholarly journals Dielectric properties of composite based on ferroelectric copolymer of poly(vinylidene fluoride-trifluoroethylene) and ferroelectric ceramics of barium lead zirconate titanate

2017 ◽  
Vol 07 (05) ◽  
pp. 1720003
Author(s):  
A. V. Solnyshkin ◽  
I. L. Kislova ◽  
I. M. Morsakov ◽  
A. N. Belov ◽  
V. I. Shevyakov ◽  
...  
Keyword(s):  
Dielectric Properties ◽  
Lead Zirconate Titanate ◽  
Vinylidene Fluoride ◽  
Composite Films ◽  
Lead Zirconate ◽  
Ferroelectric Ceramics ◽  
Zirconate Titanate ◽  
Solvent Cast ◽  
Poly Vinylidene Fluoride ◽  
Frequency Dependences

A study of dielectric properties of composite films on the base of poly(vinylidene fluoride-trifluoroethylene) copolymer P(VDF-TrFE) and ferroelectric ceramics of barium lead zirconate titanate (BPZT) solid solution is presented in this work. The composite films containing up to 50 vol.% of BPZT grains with size [Formula: see text]1[Formula: see text][Formula: see text]m were prepared by the solvent cast method. Frequency dependences of real and imaginary components of the complex permittivity were determined. The concentration dependence of the dielectric constant was discussed.

Dielectric Properties of CCTO/PVDF Composite Films

2013 ◽  
Vol 816-817 ◽  
pp. 276-279 ◽  
Author(s):  
Fang Fang Wang ◽  
Ya Jun Wang ◽  
Zhi Bo Ren
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Composite Films ◽  
Solution Casting ◽  
Casting Method ◽  
Impedance Analyzer ◽  
Composite Models ◽  
Solution Casting Method ◽  
Pvdf Matrix ◽  
Ccto Powder

To meet the requirement of microelectronic industry, ceramic/polymer composite films made of CaCu3Ti4O12(CCTO) powder as filler and PVDF copolymer as matrix were prepared by solution casting method. The dielectric properties (DP) and morphology of the films were studied by impedance analyzer and scanning electron microscope (SEM) respectively. The dielectric constant could reach 23.96 and loss 0.1082 when mass fraction of CCTO is 50% at 100 Hz. SEM results show that CCTO particles dispersed well in the PVDF matrix. At last, three composite models were used to predict the dielectric constant of the composite films and it is proved that Yamada model fits the experimental data well.

Sign in / Sign up

Export Citation Format

Share Document