scholarly journals Fast computation of multi-scale combustion systems

Author(s):  
Eliodoro Chiavazzo ◽  
Pietro Asinari ◽  
Filippo Visconti

In the present work, we illustrate the process of constructing a simplified model for complex multi-scale combustion systems. To this end, reduced models of homogeneous ideal gas mixtures of methane and air are first obtained by the novel relaxation redistribution method, and thereafter used for the extraction of all the missing variables in a reactive flow simulation with a global reaction model.

2017 ◽  
Vol 899 ◽  
pp. 173-178 ◽  
Author(s):  
Ronydes Batista Jr. ◽  
Bruna Sene Alves Araújo ◽  
Pedro Ivo Brandão e Melo Franco ◽  
Beatriz Cristina Silvério ◽  
Sandra Cristina Danta ◽  
...  

In view of the constant search for new sources of renewable energy, the particulate agro-industrial waste reuse emerges as an advantageous alternative. However, despite the advantages of using the biomass as an energy source, there is still strong resistance as the large-scale replacement of petroleum products due to the lack of scientifically proven efficient conversion technologies. In this context, the pyrolysis is presented as one of the most widely used thermal decomposition processes. The knowledge of aspects of chemical kinetics, thermodynamics these will, heat and mass transfer, are so important, since influence the quality of the product. This paper presents a kinetic study of slow pyrolysis of coffee grounds waste from dynamic thermogravimetric experiments (TG), using different powder catalysts. The primary thermal decomposition was described by the one-step reaction model, which considers a single global reaction. The kinetic parameters were estimated using nonlinear regression and the differential evolution method. The coffee ground waste was dried at 105°C for 24 hours. The sample in nature was analyzed at different heating rates, being 10, 15, 20, 30 and 50 K/min. In the catalytic pyrolysis, about 5% (w/w) of catalyst were added to the sample, at a heating rate of 30 K/min. The results show that the one-step model does not accurately represent the data of weight loss (TG) and its derivative (DTG), but can do an estimative of the activation energy reaction, and can show the differences caused by the catalysts. Although no one can say anything about the products formed with the addition of the catalyst, it would be necessary to micro-pyrolysis analysis, we can say the influence of the catalyst in the samples, based on the data obtained in thermogravimetric tests.


2021 ◽  
pp. 132442
Author(s):  
Yi Ouyang ◽  
Laurien A. Vandewalle ◽  
Lin Chen ◽  
Pieter P. Plehiers ◽  
Maarten R. Dobbelaere ◽  
...  

Author(s):  
Angela O. Nieckele ◽  
Moˆnica F. Naccache ◽  
Marcos S. P. Gomes ◽  
Joa˜o N. E. Carneiro ◽  
Andre´ Augusto Isnard ◽  
...  

The work evaluates the combustion of natural gas in a cylindrical furnace. The Generalized Finite Rate Reaction Model was selected for predicting the reactions. Two situations were considered. In the first case the combustion of the fuel was predicted by a single global reaction, and in the second case a two-step reaction was considered for predicting the combustion process. The conservation equations of mass, momentum, energy and chemical species were solved by the finite volume procedure, with the commercial software FLUENT. The turbulent flow was modeled by employing the two differential equation κ–ε model. The solutions obtained with the two reaction models, for the temperature and species concentration fields, were compared among them and against experimental data available in the literature. It was observed that the two-step reaction model represents better the physical phenomena, showing a better agreement with the experimental data.


2008 ◽  
Vol 16 (1) ◽  
Author(s):  
A. Walczak ◽  
L. Puzio

AbstractThe novel two-dimensional (2D) wavelet with anisotropic property and application of it has been presented. Wavelet is constructed in the polar coordinate system to obtain anisotropic properties. A novel edge detection method has been developed with the aid of this wavelet. This method detects gradient jump and than follows along this jump. In this way the number of calculation for edge localization is reduced. Moreover, the presented method is able to detect all edges in an image in multi-scale together with its spatial orientation. Proposed wavelet as well as edge extraction method seems to be new way to edge detection for an image.


2011 ◽  
Vol 462-463 ◽  
pp. 855-860 ◽  
Author(s):  
Takuya Toyoshi ◽  
Yoshitaka Wada ◽  
Masanori Kikuchi

From a view point of engineering application, solid-liquid flow is one of the most practical phenomena, however MPS and other particle methods usually premises a constant size of all particles in the model. In a realistic phenomenon, the size of those particles is different.  Koshizuka et al. has proposed new algorithm for solid-liquid flow simulation which is multi-scale DEM-MPS method. The method can calculate solid -liquid flow with a large difference of the particle scale. However, its program code requires a DEM part and a MPS part, and actual phenomenon includes various scales of particles. In order to analyze solid-liquid flow with different particles, modified Laplacian model and variable cut-off radius MPS method is proposed. This modification can directly deals with small particles and large particles. Calculation cost is kept and visualization of the results has more reality by these modifications.


Sign in / Sign up

Export Citation Format

Share Document