Thermophoresis and Brownian effects on natural convection of nanofluids in a square enclosure with two pairs of heat source/sink

2015 ◽  
Vol 25 (5) ◽  
pp. 1030-1046 ◽  
Author(s):  
Aminreza Noghrehabadi ◽  
Amin Samimi Behbahan ◽  
I. Pop
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Heat Source ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Numerical Results ◽  
Content Type ◽  
Source Sink

Purpose – The purpose of this paper is to study natural convection heat transfer and fluid flow in a square cavity filled with CuO-water nanofluid. Design/methodology/approach – The entire length of the bottom wall of the cavity is covered by two pairs of heat source-sink, whereas the other walls are insulated. The governing equations of fluid flow are discretized using a finite volume method with a collocated grid arrangement. The coupling between velocity and pressure is solved using the SIMPLEC and the Rhie and Chow interpolation is used to avoid the checker-board solutions for the pressure. Findings – The numerical results are reported for the effect of Rayleigh number, solid volume fraction and both presence and absence of thermophoresis and Brownian motion effects. The numerical results show an improvement in heat transfer rate for the whole range of Rayleigh numbers when Brownian and thermophoresis effects are considered. Furthermore, an increase in the Rayleigh number and nanoparticle volume fraction in both cases – when Brownian and thermophoresis effects are neglected or considered – has an excellent influence on heat transfer of nanofluids. Originality/value – The area of nanofluids is very original.

Fluid flow and heat transfer of a stratified system during natural convection – influence of chamfered corners

2019 ◽  
Vol 29 (2) ◽  
pp. 470-486 ◽  
Author(s):  
Alireza Rahimi ◽  
Aravindhan Surendar ◽  
Aygul Z. Ibatova ◽  
Abbas Kasaeipoor ◽  
Emad Hasani Malekshah
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Natural Convection ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Three Dimensional ◽  
Immiscible Fluids ◽  
Content Type ◽  
Flow And Heat Transfer

Purpose This paper aims to investigate the three-dimensional natural convection and entropy generation in the rectangular cuboid cavities included by chamfered triangular partition made by polypropylene. Design/methodology/approach The enclosure is filled by multi-walled carbon nanotubes (MWCNTs)-H2O nanofluid and air as two immiscible fluids. The finite volume approach is used for computation. The fluid flow and heat transfer are considered with combination of local entropy generation due to fluid friction and heat transfer. Moreover, a numerical method is developed based on three-dimensional solution of Navier–Stokes equations. Findings Effects of side ratio of triangular partitions (SR = 0.5, 1 and 2), Rayleigh number (103 < Ra < 105) and solid volume fraction (f = 0.002, 0.004 and 0.01 Vol.%) of nanofluid are investigated on both natural convection characteristic and volumetric entropy generation. The results show that the partitions can be a suitable method to control fluid flow and energy consumption, and three-dimensional solutions renders more accurate results. Originality/value The originality of this work is to study the three-dimensional natural convection and entropy generation of a stratified system.

Hydrothermal investigation of a stratified system in enclosure with jagged surface for application in lead-acid batteries

2019 ◽  
Vol 15 (1) ◽  
pp. 283-303 ◽  
Author(s):  
Mahmoud Salari ◽  
Emad Hasani Malekshah ◽  
Mohammad Reza Sarlak ◽  
Masoud Hasani Malekshah ◽  
Mohammad Pilfoush
Keyword(s):  
Nusselt Number ◽  
Fluid Flow ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Content Type ◽  
Lead Acid Batteries ◽  
Lead Acid

Purpose The purpose of this paper is to investigate the three-dimensional natural convection and entropy generation in a cuboid enclosure filled with two immiscible fluids of nanofluid and air. Design/methodology/approach One surface of the enclosure is jagged and another one is smooth. The finite volume approach is applied for computation. There are two partially side heaters. Furthermore, the Navier–Stokes equations and entropy generation formulation are solved in the 3D form. Findings The effects of different governing parameters, such as the jagged surface (JR=0, 0.02, 0.04, 0.08, 0.12 and 0.16), Rayleigh number (103⩽Ra⩽106) and solid volume fraction of nanofluid (φ=1, 1.5, 2 vol%), on the fluid flow, temperature field, Nusselt number, volumetric entropy generation and Bejan number are presented, comprehensively. The results indicate that the average Nusselt number increases with the increase in the Rayleigh number and solid volume fraction of nanofluid. Moreover, the flow structure is significantly affected by the jagged surface. Originality/value The originality of this work is to analyze the natural-convection fluid flow and heat transfer under the influence of jagged surfaces of electrodes in high-current lead–acid batteries.

Lattice Boltzmann simulation of free convection in nanofluid filled cavity with partially active walls – entropy generation and heatline visualization

2018 ◽  
Vol 28 (10) ◽  
pp. 2254-2283 ◽  
Author(s):  
Alireza Rahimi ◽  
Abbas Kasaeipoor ◽  
Emad Hasani Malekshah ◽  
Lioua Kolsi
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Entropy Generation ◽  
Lattice Boltzmann ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Convection Heat Transfer ◽  
Content Type ◽  
Lattice Boltzmann Simulation

Purpose This paper aims to perform the lattice Boltzmann simulation of natural convection heat transfer in cavities included with active hot and cold walls at the side walls and internal hot and cold obstacles. Design/methodology/approach The cavity is filled with double wall carbon nanotubes (DWCNTs)-water nanofluid. Different approaches such as local and total entropy generation, local and average Nusselt number and heatline visualization are used to analyze the natural convection heat transfer. The cavity is filled with DWCNTs-water nanofluid and the thermal conductivity and dynamic viscosity are measured experimentally at different solid volume fractions of 0.01 per cent, 0.02 per cent, 0.05 per cent, 0.1 per cent, 0.2 per cent and 0.5 per cent and at a temperature range of 300 to 340 (K). Findings Two sets of correlations for these parameters based on temperature and solid volume fraction are developed and used in the numerical simulations. The influences of different governing parameters such as Rayleigh number, solid volume fraction and different arrangements of active walls on the fluid flow, heat transfer and entropy generation are presented, comprehensively. It is found that the different arrangements of active walls have pronounced influence on the flow structure and heat transfer performance. Furthermore, the Nusselt number has direct relationship with Rayleigh number and solid volume fraction. On the other hand, the total entropy generation has direct and reverse relationship with Rayleigh number and solid volume fraction, respectively. Originality/value The originality of this work is to analyze the two-dimensional natural convection using lattice Boltzmann method and different approaches such as entropy generation and heatline visualization.

Influence of Cu-Water and CNT-Water Nanofluid on Natural Convection Heat Transfer in a Triangular Solar Collector

2020 ◽  
Author(s):  
Didarul Ahasan Redwan ◽  
Md. Habibur Rahman ◽  
Hasib Ahmed Prince ◽  
Emdadul Haque Chowdhury ◽  
M. Ruhul Amin
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Solar Collector ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Convection Heat Transfer ◽  
Natural Convection Heat Transfer ◽  
Convection Heat

Abstract A numerical study on natural convection heat transfer in a right triangular solar collector filled with CNT-water and Cuwater nanofluids has been conducted. The inclined wall and the bottom wall of the cavity are maintained at a relatively lower temperature (Tc), and higher temperature (Th), respectively, whereas the vertical wall, is kept adiabatic. The governing non-dimensional partial differential equations are solved by using the Galerkin weighted residual finite element method. The Rayleigh number (Ra) and the solid volume-fraction of nanoparticles (ϕ) are varied in the range of 103 ≤ Ra ≤ 106, and 0 ≤ ϕ ≤ 0.1, respectively, to carry out the parametric simulations within the laminar region. Corresponding thermal and flow fields are presented via isotherms and streamlines. Variations of average Nusselt number as a function of Rayleigh number have been examined for different solid volume-fraction of nanoparticles. It has been found that the natural convection heat transfer becomes stronger with the increment of solid volume fraction and Rayleigh number, but the strength of circulation reduces with increasing nanoparticles’ concentration at low Ra. Conduction mode dominates for lower Ra up to a certain limit of 104. It is also observed that when the solid volume fraction is increased from 0 to 0.1 for a particular Rayleigh number, the average Nusselt number is increased to a great extent, but surprisingly, the rate of increment is more pronounced at lower Ra. Moreover, it is seen that Cu-water nanofluid offers slightly better performance compared to CNT-water but the difference is very little, especially at lower Ra.

Natural convection from cross blade inside a nanofluid-filled cavity using ISPH method

2020 ◽  
Vol 30 (10) ◽  
pp. 4629-4648
Author(s):  
Zehba A.S. Raizah
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Circular Cylinder ◽  
Volume Fraction ◽  
Working Fluid ◽  
Convection Flow ◽  
Physical Parameters ◽  
Cool Temperature ◽  
Content Type

Purpose The purpose of this study is to apply the incompressible smoothed particle hydrodynamics method for simulating the natural convection flow inside a cavity including cross blades or circular cylinder cylinder. Design/methodology/approach The base fluid is water and copper-water nanofluid is treated as a working fluid. The left and rights walls are maintained at a cool temperature, the horizontal cavity walls are isolated and the inner shape was heated. The physical parameters are the length of the blades L_Blade, the number of cross blades, circular cylinder radius L_R, Rayleigh number Ra and the nanoparticles volume fraction. Findings The results reveal that the lengths of the cross blade, number of the blades and radius of the circular cylinder is working as an enhancement factor for heat transfer and fluid flows inside a cavity. Adding nanoparticles augments heat transfer and reduces the fluid flow intensity inside a cavity. The best case for buoyancy-driven flow was obtained when the inner shape is the circular cylinder at a higher Rayleigh number. Originality/value This work uses a distinctive numerical method to study the natural convection heat from cross blades inside a cavity filled with nanofluid. It provides a new analysis of this issue and presented good results.

Shape effect of nanoparticles on MHD nanofluid flow over a stretching sheet in the presence of heat source/sink with entropy generation

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Hamza Berrehal ◽  
G. Sowmya ◽  
Oluwole Daniel Makinde
Keyword(s):  
Heat Transfer ◽  
Heat Source ◽  
Heat Transfer Enhancement ◽  
Ag Nanoparticles ◽  
Stretching Sheet ◽  
Volume Fraction ◽  
Transfer Enhancement ◽  
Shooting Technique ◽  
Content Type ◽  
Source Sink

Purpose In heat transfer, fluids and nanoparticles can provide new innovative technologies with potential to adapt the heat transfer fluid’s thermal properties through control over particle size, shape and others. This paper aims to examine the effects of spherical and non-spherical (cylinder, disk, platelets, etc.) shapes of silver (Ag) nanoparticles on heat transfer enhancement and inherent irreversibility in hydromagnetic water base nanoliquid flow over a convectively heated stretching sheet with heat generation/absorption. Design/methodology/approach Applying suitable similarity constraints, the model partial differential equations are transformed into a set of nonlinear ordinary differential equations. Solutions are obtained analytically via optimal homotopy asymptotic method (OHAM) and numerically via shooting technique coupled with the Runge-Kutta-Fehlberg (RK-F) method. Findings The impact of Ag nanoparticle’s shape along with other germane factors, such as Biot number, magnetic field, solid volume fraction and heat source/sink on velocity and thermal profiles, Nusselt number, skin friction coefficient, heat transfer enhancement, rate of entropy generation and irreversibility ratio, are scrutinized via graphical simulations and discussed. This study revealed that cylindrical shape Ag nanoparticles generate high entropy and fluid friction irreversibility, whereas disk shape Ag nanoparticles exhibit high transfer enhancement rate. Moreover, a boost in magnetic field intensity, volume-fraction parameter and Biot number enhances the thermal boundary layer thickness. Originality/value The main objective of this work is to examine the different Ag nanoparticles shape effects on the heat transfer enhancement and inherent irreversibility owing to hydromagnetic nanoliquid flow past a convectively heated stretching sheet with heat source/sink, which has not been yet studied. It is hope that this study will bridge the gap in the present literature and serve as impetus to scholars, engineers and industries for more exploration in this direction. The intrinsic nonlinearity of the model equations precludes its exact solution; hence, OHAM and shooting technique coupled with the RK-F method have been used to numerically tackle the problem. Pertinent results are discussed quantitatively and displayed graphically and in tabular form.

scholarly journals Numerical study of natural convection nanofluids flow in tilted cavities with a partially thermally heat source

2021 ◽  
Vol 13 (11) ◽  
pp. 168781402110606
Author(s):  
Djamila Benyoucef ◽  
Samira Noui ◽  
Afaf Djaraoui
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Heat Source ◽  
Heat Transfer Rate ◽  
Tilt Angle ◽  
Transfer Rate ◽  
Base Fluid ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Bottom Wall

Numerically, natural convection heat transfer of nanofluids in a two-dimensional tilt square enclosure was investigated, with a partial heat source embedded on the bottom wall subject to a fixed heat flux. The remaining portions of the horizontal bottom wall are assumed to be adiabatic, while the upper horizontal wall and the vertical ones are supposed to be at a relatively low temperature. Using the finite volume method and the SIMPLER algorithm, the governing equations have been discretized and solved. Simulations have been carried out for more than one nanoparticle and base fluid, a range of Rayleigh numbers ([Formula: see text] Ra [Formula: see text]), various values of heat source length and location (0.2 [Formula: see text]  B [Formula: see text] 0.8 and 0.2 [Formula: see text]  D [Formula: see text] 0.5, respectively), solid volume fraction ([Formula: see text]) as well as tilt angle ([Formula: see text]). The results indicate that the heat transfer performance increases by adding nanoparticles into the base fluid. An optimum solid volume fraction raises and reduces the heat transfer rate and maximum temperature of the surface heat source. respectively. Moreover, the results show a significant impact of the tilt angle on the flow, temperature patterns, and the heat transfer rate with a specific tilt angle depending to the pertinent parameters.

scholarly journals Heat transfer augmentation of magnetohydrodynamics natural convection in L-shaped cavities utilizing nanofluids

2012 ◽  
Vol 16 (2) ◽  
pp. 489-501 ◽  
Author(s):  
Ehsan Sourtiji ◽  
Seyed Hosseinizadeh
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Aspect Ratio ◽  
Flow Field ◽  
Hartmann Number ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
The Magnetic Field

A numerical study of natural convection heat transfer through an alumina-water nanofluid inside L-shaped cavities in the presence of an external magnetic field is performed. The study has been carried out for a wide range of important parame?ters such as Rayleigh number, Hartmann number, aspect ratio of the cavity and solid volume fraction of the nanofluid. The influence of the nanoparticle, buoyancy force and the magnetic field on the flow and temperature fields have been plotted and discussed. The results show that after a critical Rayleigh number depending on the aspect ratio, the heat transfer in the cavity rises abruptly due to some significant changes in flow field. It is also found that the heat transfer enhances in the presence of the nanoparticles and increases with solid volume fraction of the nanofluid. In addition, the performance of the nanofluid utilization is more effective at high Ray?leigh numbers. The influence of the magnetic field has been also studied and de?duced that it has a remarkable effect on the heat transfer and flow field in the cavity that as the Hartmann number increases the overall Nusselt number is significantly decreased specially at high Rayleigh numbers.

Numerical investigation of conjugate heat transfer and entropy generation of MHD natural convection of nanofluid in an inclined enclosure

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Amin Kardgar
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Fluid Flow ◽  
Natural Convection ◽  
Entropy Generation ◽  
Wall Thickness ◽  
Conjugate Heat Transfer ◽  
Volume Fraction ◽  
Content Type ◽  
Inclined Enclosure

Purpose The purpose of this paper is to investigate conjugate heat transfer of natural convection and entropy generation of nanofluid in the presence of external magnetic field via numerical approach in an inclined square cavity enclosure. Design/methodology/approach Control volume finite volume method with collocated arrangement of grids was used for discretization of continuity, momentum, solid and fluid energy equations. Rhie and Chow interpolation technique was applied to avoid checkerboard problem in pressure field and the well-established SIMPLE algorithm was followed to deal with the pressure and velocity coupling. The cavity is filled with water and nanoparticles of the aluminum oxide (Al2O3). This study has been conducted for the certain pertinent parameters of the volume fraction of nanoparticle (φ = 0–0.08), the angle of inclination (ϴ = 0°–330°), the Ra number (Ra = 103–108), the solid to fluid conductivity ratio (ksf = 1–400), the Ha number (Ha = 0–80) and the wall thickness ratio (δ/L = 0–0.3). Findings The results indicate that averaged Nu number increases by approximately 9% by increasing volume fraction from 0.0 to 0.08. Nu increases with an increasing inclination angle to 40° and decreases abruptly in 90° because of the formation of two weaker vorticity with opposite circulation pattern intensifying the density of isotherm curves in a vertical direction. Nu increases sharply with increasing Ra more than 105. Nu also augments almost 67% by increasing ksf = 1 to ksf = 50 and remains constant by increasing ksf more than 50. Nu number reduction is almost 72% with a variation of wall thickness ratio from d/L = 0 to 0.3. Entropy generation because of fluid flow, magnetic field and heat transfer reduces linearly almost 30%, 19% and 16% by increasing volume fraction, respectively. With increasing ksf, entropy generation because of fluid flow, magnetic field and heat transfer increases asymptotically, but Bejan number decreases. Originality/value A brief review of conducted research studies in nanofluid flow and heat transfer reveals that the effect of wall thermal inertia was not investigated in MHD natural convection of nanofluids in an inclined enclosure. The aim of the present study is to analyze conjugate heat transfer in an inclined cavity filled with water and Al2O3.

Effect of trapezoidal heater on natural convection heat transfer and fluid flow inside a cubical cavity

2019 ◽  
Vol 29 (4) ◽  
pp. 1232-1248 ◽  
Author(s):  
Nikita Gibanov ◽  
Mikhail A. Sheremet
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Natural Convection ◽  
Heat Source ◽  
Convection Heat Transfer ◽  
Local Heat ◽  
Geometric Parameters ◽  
Content Type ◽  
Trapezoidal Shape ◽  
Cubical Cavity

PurposeThe purpose of this paper is to investigate natural convective heat transfer in a cubical cavity with the heat source of a trapezoidal form having a constant temperature.Design/methodology/approachThe domain of interest is a cubical cavity with two isothermal opposite vertical walls, while other walls are adiabatic. A discrete heater of a trapezoidal shape is located at the bottom wall of the cavity. Governing equations formulated in dimensionless vector potential functions, vorticity vector and temperature with corresponding initial and boundary conditions have been solved numerically using a developed computational code based on the finite difference method.FindingsThe results show that the variation of geometric parameters, such as height, length and size of the local heater, significantly influences the evolution of a temperature field and fluid flow inside the enclosure. The effects of Rayleigh number and time on streamlines, isotherms and average Nusselt number have been studied.Originality/valueThe originality of this work is to explore three-dimensional (3D) natural convection in a cubical cavity with a local heat source of trapezoidal shape, to analyze the effects of heater geometric parameters and to compare obtained 3D data with two-dimensional results.

Sign in / Sign up

Export Citation Format

Share Document