The influence of a process interruption on tensile properties of AlSi10Mg samples produced by selective laser melting

2019 ◽  
Vol 25 (8) ◽  
pp. 1442-1452 ◽  
Author(s):  
Vincent Hammond ◽  
Michael Schuch ◽  
Matthias Bleckmann
Keyword(s):  
Tensile Properties ◽  
Selective Laser Melting ◽  
Continuous Process ◽  
Processing Parameters ◽  
Laser Melting ◽  
Content Type ◽  
Random Failure ◽  
Pressure Die Casting ◽  
Suitable Technique ◽  
Cylindrical Samples

Purpose The purpose of this paper is to investigate the influence of a process interruption on the tensile properties of AlSi10Mg samples produced by selective laser melting (SLM). Design/methodology/approach Using identical processing parameters, cylindrical samples were produced in either a continuous or interrupted SLM build operation. The tensile properties and microstructure of the samples were determined as a function of process type as well as orientation. Findings All samples produced in this paper displayed superior tensile properties to those produced in high pressure die casting. In general, the samples produced in the continuous build process had higher strengths and microhardness than those produced in the interrupted process. However, while most samples displayed random failure locations, the vertical samples produced in the interrupted build process showed a strong tendency for localized failure in the vicinity of the stoppage plane. Originality/value This paper demonstrated that samples produced in an interrupted build process tend to have poorer mechanical properties than those produced in a continuous process. Together, these observations highlight the importance of a suitable technique for restarting and completing an interrupted build process to ensure the production of high quality components.

Correlation Between Microstructure and Tensile Properties of STS 316L and Inconel 718 Fabricated by Selective Laser Melting (SLM)

2020 ◽  
Vol 20 (11) ◽  
pp. 6807-6814
Author(s):  
Jungsub Lee ◽  
Minshik Lee ◽  
Im Doo Jung ◽  
Jungho Choe ◽  
Ji-Hun Yu ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Tensile Properties ◽  
Selective Laser Melting ◽  
Inconel 718 ◽  
Tensile Elongation ◽  
Processing Condition ◽  
Processing Parameters ◽  
Fusion Pore ◽  
Laser Melting ◽  
Track Width

The correlation between microstructure and tensile properties of selective laser melting (SLM) processed STS 316L and Inconel 718 were investigated at various heights (top, middle and bottom) and planes (YZ, ZX and XY). Columnar grains and dendrites were formed by directional growth during solidification. The average melt pool width and depth, and scan track width were similar in both specimens due to fixed processing parameters. SLM Inconel 718 has moderate tensile strength (1165 MPa) and tensile elongation (11.5%), whereas SLM STS 316L has outstanding tensile strength (656 MPa) and tensile elongation (75%) compared to other SLM processed STS 316L. Fine columnar diameter (0.5 μm) and dense microstructures (porosity: 0.35%) in SLM STS 316L promoted the enhancement of tensile elongation by suitable processing condition. Fractographic analysis suggested that the lack of fusion pore with unmelted powder should be avoided to increase tensile properties by controlling processing parameters.

scholarly journals Optimisation of selective laser melting parameters for the Ni-based superalloy IN-738 LC using Doehlert’s design

2017 ◽  
Vol 23 (5) ◽  
pp. 881-892 ◽  
Author(s):  
Nataliya Perevoshchikova ◽  
Jordan Rigaud ◽  
Yu Sha ◽  
Martin Heilmaier ◽  
Barrie Finnin ◽  
...  
Keyword(s):  
Image Analysis ◽  
Relative Density ◽  
Selective Laser Melting ◽  
Processing Parameters ◽  
Powder Alloy ◽  
Operating Parameters ◽  
Laser Melting ◽  
Doehlert Design ◽  
Feasible Set ◽  
Content Type

Purpose The Ni-based superalloy IN-738 LC is known to be susceptible to porosity and different types of cracking during the build-up process and, thus, challenging to manufacture using selective laser melting (SLM). Determining a feasible set of operating parameters for SLM of nickel-based superalloys involves new approach to experimental design based on the Doehlert method that assists in determining an optimal (feasible) set of operating parameters for SLM of IN-738 LC powder alloy. Design/methodology/approach The SLM parameters are evaluated in terms of their effectiveness in obtaining the microstructure with a porosity content of <0.5 per cent and without micro-cracking. The experimental approach is exemplified with the Doehlert matrix response variable, relative density, by comparing Archimedes method with microstructural assessments of pores and cracks from image analysis. The effect of heat treatment (HT) and hot isostatic pressing (HIP) on the microstructure of the SLMed IN-738 LC powder alloy has been examined and the consequential tensile response characterised. Findings By using optimised process parameters (low heat input, medium scanning speed and small hatching distance) which provides medium energy density, samples of IN-738 LC with a macroscopic porosity <0.5 per cent and free of micro-cracks can be manufactured by SLM. The results indicate that HIP of SLMed material did not lead to a noticeable effect on mechanical properties compared to HT of SLMed material suggesting that the level of both porosity and crack density might be already below the detection limit for the mere heat-treated material. Originality/value SLM processing parameters (power, scan speed, hatching distance) for IN-738 LC were successfully optimised after only 14 experiments using Doehlert design. Two independent methods, Archimedes method and image analysis, were used in this study to assess relative density of SLM-produced samples with sets of processing parameters showing coherency in prediction with predicted response by Doehlert design.

Effect of processing parameters on forming defects during selective laser melting of AlSi10Mg powder

2020 ◽  
Vol 26 (5) ◽  
pp. 871-879 ◽  
Author(s):  
Haihua Wu ◽  
Junfeng Li ◽  
Zhengying Wei ◽  
Pei Wei
Keyword(s):  
Selective Laser Melting ◽  
Laser Power ◽  
Scanning Speed ◽  
Processing Parameters ◽  
Argon Pressure ◽  
Powder Layer ◽  
Laser Melting ◽  
Content Type ◽  
Scan Speed ◽  
Forming Defects

Purpose To fabricate a selective laser melting (SLM)-processed AlSi10Mg part with almost full density and free of any apparent pores, this study aims to investigate the effect of ambient argon pressure and laser scanning speed on the particles splash during the AlSi10Mg powder bed laser melting. Design/methodology/approach Based on the discrete element method (DEM), a 3D model of random distribution of powder particles was established, and the 3D free surface of SLM forming process was dynamically tracked by the volume of fluid, where a Gaussian laser beam acts as the energy source melting the powder bed. Through the numerical simulation and process experimental research, the effect of the applied laser power and scanning speed on the operating laser melting temperature was studied. Findings The process stability has a fundamental role in the porosity formation, which is process-dependent. The effect of the processing conditions on the process stability and the resultant forming defects were clarified. Research limitations/implications The results shows that the pores were the main defects present in the SLM-processed AlSi10Mg sample, which decreases the densification level of the sample. Practical implications The optimal processing parameters (argon pressure of 1,000 Pa, laser power of 180 W, scan speed of 1,000 mm/s, powder layer thickness of 35 µm and hatch spacing of 50 µm ) applied during laser melting can improve the quality of selective laser melting of AlSi10Mg, Social implications It can provide a technological support for 3D printing. Originality/value Based on the analysis of the pore and balling formation mechanisms, the optimal processing parameters have been obtained, which were argon pressure of 1,000 Pa, laser power of 180 W, scan speed of 1,000 mm/s, powder layer thickness of 35 µm and hatch spacing of 50 µm. Then, a near-fully dense sample free of any apparent pores on the cross-sectional microstructure was produced by SLM, wherein the relative density of the as-built samples is larger than 97.5%.

Selective laser melting (SLM) of pure gold for manufacturing dental crowns

2014 ◽  
Vol 20 (6) ◽  
pp. 471-479 ◽  
Author(s):  
Mushtaq Khan ◽  
Phill Dickens
Keyword(s):  
Mechanical Properties ◽  
Layer Thickness ◽  
Surface Quality ◽  
Selective Laser Melting ◽  
Processing Parameters ◽  
Pure Gold ◽  
Laser Melting ◽  
Content Type ◽  
Dental Crowns ◽  
Suitable Processing

Purpose – This paper aims to present the application aspect of the work to manufacturing premolar and molar dental crowns by selective laser melting (SLM) of pure gold. Over the years different metals have been processed using laser-based Additive Manufacturing processes, but very little work has been published on the SLM of gold (Au). Previously published work presented suitable processing parameters for SLM of pure gold. Design/methodology/approach – Suitable processing parameters were used to manufacture premolar and molar dental crowns using SLM system. Different layer thickness was used to analyse the effect on surface quality of crowns. Mechanical properties are checked using nanoindentation and micro Computerized Tomography scanning. Findings – Dental crowns were successfully manufacturing using new build platform and suitable processing parameters. Parts were manufacturing using minimal supports which prevented parts from damaging during removal. A bed temperature of 100°C was found suitable for reducing warpage in the layers. Layer thickness of 50μm was found to have better surface quality and structural integrity as compared to 75μm. Porosity was found to be predominantly inter-layer. Small difference in mechanical properties of dental crowns is associated with the laser processing. Originality/value – This research is the first of its kind which presents dental crown manufacturing using SLM of pure gold.

Geometrical feature analysis of Co-Cr-Mo single tracks after selective laser melting processing

2015 ◽  
Vol 21 (3) ◽  
pp. 287-300 ◽  
Author(s):  
Karla Monroy ◽  
Jordi Delgado ◽  
Lidia Sereno ◽  
Joaquim Ciurana ◽  
Nicolas J Hendrichs
Keyword(s):  
Selective Laser Melting ◽  
Scanning Speed ◽  
Processing Parameters ◽  
Single Track ◽  
Cobalt Chromium ◽  
Laser Melting ◽  
Content Type ◽  
Dimensional Precision ◽  
Morphologic Characteristics ◽  
Definition Of

Purpose – Therefore, the purpose of this study is to understand the relationships between the processing parameters and the geometric form of the produced single tracks, in order to control dimensional quality in future experimentations. The quality of the deposited single track and layer is of prime importance in the selective laser melting (SLM) process, as it affects the product quality in terms of dimensional precision and product performance. Design/methodology/approach – In this paper, a vertical milling machining center equipped with an Ytterbium-fiber laser was used in the SLM experimentation to form single cobalt-chromium-molybdenum (CoCrMo) tracks. The different geometric features and the influence of the scanning parameters on these morphologic characteristics were studied statistically by means of ANOVA. Findings – Evidently, track height (h1) inaccuracy reduced in layer thicknesses between 100 and 200 μm. The re-melt depth (h2) was determined by the energy parameters, with laser power of 325-350 W and scanning speed (SS) of 66.6-83.3 mm/s being the most favorable parameters to obtain the required anchoring. Moreover, a contact angle of 117° was proposed as optimal, as it permitted an adequate overlapping region and a full densification, and, finally, an SS of 50 mm/s and a layer thickness of 250 were suggested for its development. Originality/value – The comprehension of the phenomena inherent to the process is related to the single track geometrical characteristics, which allow the definition of an optimal value for each factor for a further proposal of processing conditions that can finally derive a higher precision, wetting, density and mechanical properties.

scholarly journals Processing of metal-diamond-composites using selective laser melting

2015 ◽  
Vol 21 (2) ◽  
pp. 130-136 ◽  
Author(s):  
Adriaan Bernardus Spierings ◽  
Christian Leinenbach ◽  
Christoph Kenel ◽  
Konrad Wegener
Keyword(s):  
Selective Laser Melting ◽  
Feasibility Study ◽  
Matrix Material ◽  
Outer Part ◽  
Processing Parameters ◽  
Added Value ◽  
Laser Melting ◽  
Content Type ◽  
Diamond Particles ◽  
The Matrix

Purpose – The purpose of this paper is a feasibility study that was performed to investigate the basic processability of a diamond-containing metal matrix. Powder-bed-based additive manufacturing processes such as selective laser melting (SLM) offer a huge degree of freedom, both in terms of part design and material options. In that respect, mixtures of different powders can offer new ways for the manufacture of materials with tailored properties for special applications such as metal-based cutting or grinding tools with incorporated hard phases. Design/methodology/approach – A two-step approach was used to first investigate the basic SLM-processability of a Cu-Sn-Ti-Zr alloy, which is usually used for the active brazing of ceramics and superhard materials. After the identification of a suitable processing window, the processing parameters were then applied to a mixture of this matrix material with 10-20 volume per cent artificial, Ni-coated mono-crystalline diamonds. Findings – Even though the processing parameters were not yet optimized, stable specimens out of the matrix material could be produced. Also, diamond-containing mixtures with the matrix material resulted in stable specimens, where the diamonds survived the layer-wise build process with the successive heat input, as almost no graphitization was observed. The diamond particles are fully embedded in the Cu-Sn-Ti-Zr matrix material. The outer part of the diamonds partly dissolves in the matrix during the SLM process, forming small TiC particles and most likely a thin TiC layer around the diamond particles. Originality/value – The feasibility study approved the SLM processing capabilities of a metal-diamond composite. Although some cracking phenomena sill occur, this seems to be an interesting and promising way to create new abrasive tools with added value in terms of internal and local lubrication supply, tooling temperature control and improved tooling durability.

Effect of internal pores on tensile properties of Co-Cr-Mo alloy fabricated by selective laser melting

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Hyeon-Tae Im ◽  
Hyun-Su Kang ◽  
Hyeon-Goo Kang ◽  
Hyo Kyu Kim ◽  
Jun Choi ◽  
...  
Keyword(s):  
Tensile Properties ◽  
Selective Laser Melting ◽  
Volume Fraction ◽  
Tensile Deformation ◽  
Hot Isostatic Pressing ◽  
Tensile Tests ◽  
Laser Melting ◽  
Content Type ◽  
Tensile Deformation Behavior ◽  
Ε Phase

Purpose The purpose of this paper is to examine the effect of internal pores on the tensile properties of a Co–Cr–Mo alloy fabricated by selective laser melting (SLM). Design/methodology/approach The size and volume fraction of pores were controlled through high temperature annealing (HTA) and hot isostatic pressing (HIP). Findings After HTA, the size and fraction of pores decreased compared with the as-built SLM sample, and no pores were observed after HIP. Tensile tests of the HTA and HIP samples showed nearly similar tensile deformation behavior. From the results, the authors found that the size of the internal pores formed in the SLM process had little effect on the tensile properties. The as-built SLM sample had less elongation than the HTA and HIP samples, which would not the effect of porosity, but rather the effect of the residual stress and the retained ε phase after the SLM process. Originality/value Although pores are a main factor that influence the mechanical properties, the effect of pores on the tensile properties of Co–Cr–Mo alloys fabricated by SLM has not been studied. Therefore, in this study, the effect of pores on the tensile properties of a Co–Cr–Mo alloy fabricated by SLM was studied.

Melting, fusion and solidification behaviors of Ti-6Al-4V alloy in selective laser melting at different scanning speeds

2020 ◽  
Vol 26 (7) ◽  
pp. 1209-1215 ◽  
Author(s):  
Snehashis Pal ◽  
Gorazd Lojen ◽  
Nenad Gubeljak ◽  
Vanja Kokol ◽  
Igor Drstvensek
Keyword(s):  
Tensile Properties ◽  
Selective Laser Melting ◽  
Solidification Process ◽  
Fabrication Process ◽  
Laser Melting ◽  
Content Type ◽  
Melt Pool ◽  
High Thermal Gradient ◽  
Thermal Phenomena ◽  
Pool Formation

Purpose Melting, fusion and solidification are the principal mechanisms used in selective laser melting to produce a product. Several thermal phenomena occur during the fabrication process, such as powder melting, melt pool formation, mixing of materials (fusion), rapid solidification, re-melting, high thermal gradient, reheating and cooling. These phenomena result in several types of pores, defects, irregular surfaces, bending and residual stress. This paper aims to focus on the physical behaviors of Ti-6Al-4V alloy at several scanning speeds and their effect on porosity and metallurgical properties. Design/methodology/approach Seven scanning speeds between 150  and 1000 mm/s were chosen to observe the occurrence of different pores, defects and microstructural formations and their effect on hardness and tensile properties. Findings The various mentioned malformations occur due to the results of possible uncertainties during the melting-fusion-solidification process. Size, shape, number, location and content of the pores varied in different samples. The a cicular a' size changes with different scanning speeds. Eventually, both porosity and microstructure have shown influential consequences on the hardness and tensile properties in the samples manufactured with different scanning speeds. Originality/value This study showed the adverse effects of different physical behaviors that occurred during the fabrication process, leading to the formation of complex pores. The causations and plausible solutions of the pore formation are interpreted in this paper. The authors observe that a circular a' size differed with scanning speeds, and these influence the mechanical properties.

Sign in / Sign up

Export Citation Format

Share Document