Effect of WEDM process parameters on machinability of Nimonic75 alloy using brass wire

2020 ◽  
Vol 17 (3) ◽  
pp. 389-397
Author(s):  
Harvinder Singh ◽  
Vinod Kumar ◽  
Jatinder Kapoor
Keyword(s):  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Cutting Speed ◽  
Content Type ◽  
Response Characteristics ◽  
Nickel Based Alloy ◽  
Pulse On Time ◽  
Pulse Off Time

Purpose This study aims to investigate the influence of process parameters of wire electrical discharge machining (WEDM) of Nimonic75. Nimonic75 is a Nickel-based alloy mostly used in the aerospace industry for its strength at high temperature. Design/methodology/approach One factor at a time (OFAT) approach has been used to perform the experiments. Pulse on time, pulse off time, peak current and servo voltage were chosen as input process parameters. Cutting speed, material removal rate and surface roughness (Ra) were selected as output performance characteristics. Findings Through experimental work, the effect of process parameters on the response characteristics has been found. Results identified the most important parameters to maximize the cutting speed and material removal rate and minimize Ra. Originality/value Very limited research work has been done on WEDM of Nickel-based alloy Nimonic75. Therefore, the aim of this paper to conduct preliminary experimentation for identifying the parameters, which influence the response characteristics such as material removal rate, cutting speed, Ra, etc. during WEDM of Nickel-based alloy (Nimonic75) using OFAT approach and found the machinability of Nimonic75 for further exhaustive experimentation work.

Optimization of WEDM Process Parameters

2014 ◽  
Vol 592-594 ◽  
pp. 831-835 ◽  
Author(s):  
Vikram Singh ◽  
Sharad Kumar Pradhan
Keyword(s):  
Surface Roughness ◽  
Response Surface ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Wedm Process

The objective of the present work is to investigate the effects of various WEDM process parameters like pulse on time, pulse off time, corner servo, flushing pressure, wire feed rate, wire tension, spark gap voltage and servo feed on the material removal rate (MRR) & Surface Roughness (SR) and to obtain the optimal settings of machining parameters at which the material removal rate (MRR) is maximum and the Surface Roughness (SR) is minimum in a range. In the present investigation, Inconel 825 specimen is machined by using brass wire as electrode and the response surface methodology (RSM) is for modeling a second-order response surface to estimate the optimum machining condition to produce the best possible response within the experimental constraints.

Effects of Process Parameters on Material Removal Rate and Surface Roughness in Wedm of H-13 Die Tool Steel

2018 ◽  
Vol 28 ◽  
pp. 55-66 ◽  
Author(s):  
Kuldeep Singh ◽  
Khushdeep Goyal ◽  
Deepak Kumar Goyal
Keyword(s):  
Surface Roughness ◽  
Taguchi Method ◽  
Tool Steel ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Pulse On Time ◽  
Pulse Off Time

In research work variation of cutting performance with pulse on time, pulse off time, wire type, and peak current were experimentally investigated in wire electric discharge machining (WEDM) process. Soft brass wire and zinc coated diffused wire with 0.25 mm diameter and Die tool steel H-13 with 155 mm× 70 mm×14 mm dimensions were used as tool and work materials in the experiments. Surface roughness and material removal rate (MRR) were considered as performance output in this study. Taguchi method was used for designing the experiments and optimal combination of WEDM parameters for proper machining of Die tool steel (H-13) to achieve better surface finish and material removal rate. In addition the most significant cutting parameter is determined by using analysis of variance (ANOVA). Keywords Machining, Process Parameters, Material removal rate, Surface roughness, Taguchi method

scholarly journals Experimental Investigation of Edm Die Sinking Process Parameters on Aluminium Alloy 5083 Using Design of Experiment

2017 ◽  
Vol 4 (1) ◽  
pp. 138-144
Author(s):  
Wahaizad Safiei ◽  
Muhamad Ridzuan Radin Muhamad Amin
Keyword(s):  
Surface Roughness ◽  
Aluminium Alloy ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Design Of Experiment ◽  
Material Removal ◽  
Removal Rate ◽  
Peak Current ◽  
Pulse On Time ◽  
Pulse Off Time

In this paper, the results of surface roughness (Ra) and material removal rate (MRR) are presented based on experimental studies of Electrical Discharge Machining (EDM) process parameters. Pulse ON time, pulse OFF time, peak current, gap voltage and jump speed are the selected input parameters and the experiments were conducted with Aluminium Alloy 5083 as a workpiece, copper as an electrode and the response variables are surface roughness (Ra) and material removal rate (MRR). Design of Experiment and Analysis of Variance (ANOVA) were applied to identify the optimum settings.The result shows that the significant factors for the value of surface roughness (Ra) and material removal rate (MRR) are pulses ON time and peak current.

scholarly journals A Study on Optimization of Process Parameters in Machining of Bronze using Wire-EDM

2021 ◽  
pp. 484-493
Author(s):  
Gajanan Kamble ◽  
Dr. N. Lakshamanaswamy ◽  
Gangadhara H S ◽  
Sharon Markus ◽  
N. Rajath
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Machining Parameters ◽  
Wire Edm ◽  
Pulse On Time ◽  
Pulse Off Time

Wire cut electrical discharge machining (WEDM) is a hybrid manufacturing technology which enables machining of all engineering materials. This research article deals with investigation on Optimization of the Process Parameters of the wire cut EDM of Bronze material of dimension (80*80*40) in mm. Material removal rate, Surface roughness and Kerf width were studied against the process parameters such as Pulse on time(TON), Pulse off time (TOFF) and Current(IP). The machining parameters for wire EDM were optimized for achieving the combined objectives. As there are three input parameters 27 experiments is carried out and full factorial is used. Optimized parameters were found using (ANOVA) and the error percentage can be validated and parameter contribution for the Material removal rate (MRR) and Surface roughness were found.

Enhancement of EDM Performance by Using Copper-Silver Composite Electrode

2020 ◽  
Vol 38 (9A) ◽  
pp. 1352-1358
Author(s):  
Saad K. Shather ◽  
Abbas A. Ibrahim ◽  
Zainab H. Mohsein ◽  
Omar H. Hassoon
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
High Speed ◽  
Composite Electrode ◽  
Removal Rate ◽  
Pure Copper ◽  
High Speed Steel ◽  
Pulse On Time ◽  
Pulse Off Time

Discharge Machining is a non-traditional machining technique and usually applied for hard metals and complex shapes that difficult to machining in the traditional cutting process. This process depends on different parameters that can affect the material removal rate and surface roughness. The electrode material is one of the important parameters in Electro –Discharge Machining (EDM). In this paper, the experimental work carried out by using a composite material electrode and the workpiece material from a high-speed steel plate. The cutting conditions: current (10 Amps, 12 Amps, 14 Amps), pulse on time (100 µs, 150 µs, 200 µs), pulse off time 25 µs, casting technique has been carried out to prepare the composite electrodes copper-sliver. The experimental results showed that Copper-Sliver (weight ratio70:30) gives better results than commonly electrode copper, Material Removal Rate (MRR) Copper-Sliver composite electrode reach to 0.225 gm/min higher than the pure Copper electrode. The lower value of the tool wear rate achieved with the composite electrode is 0.0001 gm/min. The surface roughness of the workpiece improved with a composite electrode compared with the pure electrode.

scholarly journals Multi- Response Optimization of Wire EDM Process Parameter on Aluminium Alloy (5086)

2020 ◽  
Vol 10 (1) ◽  
pp. 224-229
Keyword(s):  
Aluminium Alloy ◽  
Material Removal Rate ◽  
Material Removal ◽  
Control Parameter ◽  
Removal Rate ◽  
Response Optimization ◽  
High Pulse ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

In the present work, the effect of process parameters on material removal rate during the machining of aluminium alloy (5086) with WEDM is studied. The four control parameter were selected i.e pulse on time (TON), pulse off time (TOFF), peak current (IP), and spark gap voltage (SV) to investigate their effects on material removal rate (MRR). Each control parameter had three levels. Total 27 experiments were done with a zinc coated brass wire of diameter 0.25 mm. Taguchi L9 orthogonal array technique was used for the experiment. ANOVA was used to find out the significance of control parameters and their contribution on MRR. It was found that maximum material removal rate was 41.52 mm3 /min which was due to high pulse on time and low pulse off time.

Influence of Input Factors on Material Removal Rate in PMEDM Cylindrical Shaped Parts with Silicon Carbide Powder Suspended Dielectric

2020 ◽  
Vol 861 ◽  
pp. 129-135 ◽  
Author(s):  
Manh Cuong Nguyen ◽  
Luu Anh Tung ◽  
Bui Thanh Danh ◽  
Nguyen Van Cuong ◽  
Tran Thi Hong ◽  
...  
Keyword(s):  
Material Removal Rate ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Carbide Powder ◽  
Powder Concentration ◽  
Five Factors ◽  
Cylindrical Parts ◽  
Pulse On Time ◽  
Pulse Off Time

This work is done to determine the effects of the input factors of powder mixed electrical discharge machining (PMEDM) process on the material removal rate (MRR). In the study, the workpiece is cylindrical parts made from 90CrSi alloy steel. Also, five factors containing the pulse on time Ton, the powder concentration Cp, the pulse off time Toff, the pulse current IP, and the server voltage SV were discovered to find their impact on MRR. In addition, the Taguchi method and ANOVA analysis were used to design experiment and analyze the results. In addition, an optimal model of the MRR was introduced. Also, the model has been well verified by comparison with testing, and so it can be used for further studies in the PMEDM process.

Nano Graphite Powder Assisted Electric Discharge Machining Characteristics of ZM21 Magnesium Alloy

2015 ◽  
Vol 787 ◽  
pp. 406-410
Author(s):  
S. Santosh ◽  
S. Javed Syed Ibrahim ◽  
P. Saravanamuthukumar ◽  
K. Rajkumar ◽  
K.L. Hari Krishna
Keyword(s):  
Magnesium Alloy ◽  
Material Removal Rate ◽  
Electric Discharge ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Parameters ◽  
Electric Discharge Machining ◽  
Zm21 Magnesium Alloy ◽  
Pulse On Time ◽  
Pulse Off Time

Magnesium alloys are used in many applications, particularly in orthopaedic implants are very difficult to machine by conventional processes because of their complex 3D structure and limited slip system at room temperature. Hence there is an inherent need for alternative processes for machining such intricate profiles. Electric Discharge Machining is growing rapidly in tool rooms, die shops and even in general shop floors of modern industries to facilitate complex machining for difficult-to-machine materials and provide better surface integrity. Therefore, the use of electric discharge machining on ZM21 magnesium alloy is attempted in this paper. Nanographite powder is added for machining zone to enhance the electrical conductivity of EDM oil by way it improves the machining performance. Machining parameters such as the current, pulse on time and pulse off time were process parameters to explore their effects on the material removal rate and tool wear rate. It is observed that, an increased material removal rate was due to the enhanced electrical and thermal conductivity of the EDM oil.

Influence of Process Parameters on Characteristics of Electrical Discharge Machining of PH17-4 Stainless Steel

2015 ◽  
Vol 14 (03) ◽  
pp. 189-202 ◽  
Author(s):  
V. Vikram Reddy ◽  
P. Madar Valli ◽  
A. Kumar ◽  
Ch. Sridhar Reddy
Keyword(s):  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Surface Hardness ◽  
Machining Process ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

In the present work, an investigation has been made into the electrical discharge machining process during machining of precipitation hardening stainless steel PH17-4. Taguchi method is used to formulate the experimental layout, to analyze the effect of each process parameter on machining characteristics and to predict the optimal choice for each electrical discharge machining process parameters namely, peak current, pulse on time and pulse off time that give up optimal process performance characteristics such as material removal rate, surface roughness, tool wear rate and surface hardness. To identify the significance of parameters on measured response, the analysis of variance has been done. It is found that parameters peak current and pulse on time have the significant affect on material removal rate, surface roughness, tool wear rate and surface hardness. However, parameter pulse off time has significant affect on material removal rate. Confirmation tests are conducted at their respective optimum parametric settings to verify the predicted optimal values of performance characteristics.

Optimization of Process Parameters on Ti-6Al-4V Using Central Composite Design Method

2011 ◽  
Vol 189-193 ◽  
pp. 1393-1400 ◽  
Author(s):  
M.M. Rahman
Keyword(s):  
Surface Roughness ◽  
Wear Rate ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Peak Current ◽  
Long Pulse ◽  
Pulse On Time

Electrical discharge machining (EDM) is relatively modern machining process having distinct advantages over other machining processes and able to machine Ti-alloys effectively. This paper attempts to investigate the effects of process parameters on output response of titanium alloy Ti-6Al-4V in EDM utilizing copper tungsten as an electrode and positive polarity of the electrode. Mathematical models for material removal rate (MRR), electrode wear rate (EWR) and surface roughness (SR) are developed in this paper. Design of experiments method and response surface methodology techniques are implemented. The validity test of the fit and adequacy of the proposed models has been carried out through analysis of variance. It can be seen that as the peak current increases the TWR decreases till certain ampere and then increases. The excellent surface finish is investigated in this study at short pulse on time and in contrast the long pulse duration causes the lowest EWR. Long pulse off time provides minimum EWR and the impact of pulse interval on EWR depends on peak current. The result leads to wear rate of electrode and economical industrial machining by optimizing the input parameters. It found that the peak current, servo voltage and pulse on time are significant in material removal rate and surface roughness. Peak current has the greater impact on surface roughness and material removal rate.

Sign in / Sign up

Export Citation Format

Share Document