scholarly journals Experimental Investigation of Edm Die Sinking Process Parameters on Aluminium Alloy 5083 Using Design of Experiment

2017 ◽  
Vol 4 (1) ◽  
pp. 138-144
Author(s):  
Wahaizad Safiei ◽  
Muhamad Ridzuan Radin Muhamad Amin
Keyword(s):  
Surface Roughness ◽  
Aluminium Alloy ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Design Of Experiment ◽  
Material Removal ◽  
Removal Rate ◽  
Peak Current ◽  
Pulse On Time ◽  
Pulse Off Time

In this paper, the results of surface roughness (Ra) and material removal rate (MRR) are presented based on experimental studies of Electrical Discharge Machining (EDM) process parameters. Pulse ON time, pulse OFF time, peak current, gap voltage and jump speed are the selected input parameters and the experiments were conducted with Aluminium Alloy 5083 as a workpiece, copper as an electrode and the response variables are surface roughness (Ra) and material removal rate (MRR). Design of Experiment and Analysis of Variance (ANOVA) were applied to identify the optimum settings.The result shows that the significant factors for the value of surface roughness (Ra) and material removal rate (MRR) are pulses ON time and peak current.

Optimization of Process Parameters on Ti-6Al-4V Using Central Composite Design Method

2011 ◽  
Vol 189-193 ◽  
pp. 1393-1400 ◽  
Author(s):  
M.M. Rahman
Keyword(s):  
Surface Roughness ◽  
Wear Rate ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Peak Current ◽  
Long Pulse ◽  
Pulse On Time

Electrical discharge machining (EDM) is relatively modern machining process having distinct advantages over other machining processes and able to machine Ti-alloys effectively. This paper attempts to investigate the effects of process parameters on output response of titanium alloy Ti-6Al-4V in EDM utilizing copper tungsten as an electrode and positive polarity of the electrode. Mathematical models for material removal rate (MRR), electrode wear rate (EWR) and surface roughness (SR) are developed in this paper. Design of experiments method and response surface methodology techniques are implemented. The validity test of the fit and adequacy of the proposed models has been carried out through analysis of variance. It can be seen that as the peak current increases the TWR decreases till certain ampere and then increases. The excellent surface finish is investigated in this study at short pulse on time and in contrast the long pulse duration causes the lowest EWR. Long pulse off time provides minimum EWR and the impact of pulse interval on EWR depends on peak current. The result leads to wear rate of electrode and economical industrial machining by optimizing the input parameters. It found that the peak current, servo voltage and pulse on time are significant in material removal rate and surface roughness. Peak current has the greater impact on surface roughness and material removal rate.

Optimization of WEDM Process Parameters

2014 ◽  
Vol 592-594 ◽  
pp. 831-835 ◽  
Author(s):  
Vikram Singh ◽  
Sharad Kumar Pradhan
Keyword(s):  
Surface Roughness ◽  
Response Surface ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Wedm Process

The objective of the present work is to investigate the effects of various WEDM process parameters like pulse on time, pulse off time, corner servo, flushing pressure, wire feed rate, wire tension, spark gap voltage and servo feed on the material removal rate (MRR) & Surface Roughness (SR) and to obtain the optimal settings of machining parameters at which the material removal rate (MRR) is maximum and the Surface Roughness (SR) is minimum in a range. In the present investigation, Inconel 825 specimen is machined by using brass wire as electrode and the response surface methodology (RSM) is for modeling a second-order response surface to estimate the optimum machining condition to produce the best possible response within the experimental constraints.

Effects of Process Parameters on Material Removal Rate and Surface Roughness in Wedm of H-13 Die Tool Steel

2018 ◽  
Vol 28 ◽  
pp. 55-66 ◽  
Author(s):  
Kuldeep Singh ◽  
Khushdeep Goyal ◽  
Deepak Kumar Goyal
Keyword(s):  
Surface Roughness ◽  
Taguchi Method ◽  
Tool Steel ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Pulse On Time ◽  
Pulse Off Time

In research work variation of cutting performance with pulse on time, pulse off time, wire type, and peak current were experimentally investigated in wire electric discharge machining (WEDM) process. Soft brass wire and zinc coated diffused wire with 0.25 mm diameter and Die tool steel H-13 with 155 mm× 70 mm×14 mm dimensions were used as tool and work materials in the experiments. Surface roughness and material removal rate (MRR) were considered as performance output in this study. Taguchi method was used for designing the experiments and optimal combination of WEDM parameters for proper machining of Die tool steel (H-13) to achieve better surface finish and material removal rate. In addition the most significant cutting parameter is determined by using analysis of variance (ANOVA). Keywords Machining, Process Parameters, Material removal rate, Surface roughness, Taguchi method

scholarly journals A Study on Optimization of Process Parameters in Machining of Bronze using Wire-EDM

2021 ◽  
pp. 484-493
Author(s):  
Gajanan Kamble ◽  
Dr. N. Lakshamanaswamy ◽  
Gangadhara H S ◽  
Sharon Markus ◽  
N. Rajath
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Machining Parameters ◽  
Wire Edm ◽  
Pulse On Time ◽  
Pulse Off Time

Wire cut electrical discharge machining (WEDM) is a hybrid manufacturing technology which enables machining of all engineering materials. This research article deals with investigation on Optimization of the Process Parameters of the wire cut EDM of Bronze material of dimension (80*80*40) in mm. Material removal rate, Surface roughness and Kerf width were studied against the process parameters such as Pulse on time(TON), Pulse off time (TOFF) and Current(IP). The machining parameters for wire EDM were optimized for achieving the combined objectives. As there are three input parameters 27 experiments is carried out and full factorial is used. Optimized parameters were found using (ANOVA) and the error percentage can be validated and parameter contribution for the Material removal rate (MRR) and Surface roughness were found.

Enhancement of EDM Performance by Using Copper-Silver Composite Electrode

2020 ◽  
Vol 38 (9A) ◽  
pp. 1352-1358
Author(s):  
Saad K. Shather ◽  
Abbas A. Ibrahim ◽  
Zainab H. Mohsein ◽  
Omar H. Hassoon
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
High Speed ◽  
Composite Electrode ◽  
Removal Rate ◽  
Pure Copper ◽  
High Speed Steel ◽  
Pulse On Time ◽  
Pulse Off Time

Discharge Machining is a non-traditional machining technique and usually applied for hard metals and complex shapes that difficult to machining in the traditional cutting process. This process depends on different parameters that can affect the material removal rate and surface roughness. The electrode material is one of the important parameters in Electro –Discharge Machining (EDM). In this paper, the experimental work carried out by using a composite material electrode and the workpiece material from a high-speed steel plate. The cutting conditions: current (10 Amps, 12 Amps, 14 Amps), pulse on time (100 µs, 150 µs, 200 µs), pulse off time 25 µs, casting technique has been carried out to prepare the composite electrodes copper-sliver. The experimental results showed that Copper-Sliver (weight ratio70:30) gives better results than commonly electrode copper, Material Removal Rate (MRR) Copper-Sliver composite electrode reach to 0.225 gm/min higher than the pure Copper electrode. The lower value of the tool wear rate achieved with the composite electrode is 0.0001 gm/min. The surface roughness of the workpiece improved with a composite electrode compared with the pure electrode.

scholarly journals Multi- Response Optimization of Wire EDM Process Parameter on Aluminium Alloy (5086)

2020 ◽  
Vol 10 (1) ◽  
pp. 224-229
Keyword(s):  
Aluminium Alloy ◽  
Material Removal Rate ◽  
Material Removal ◽  
Control Parameter ◽  
Removal Rate ◽  
Response Optimization ◽  
High Pulse ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

In the present work, the effect of process parameters on material removal rate during the machining of aluminium alloy (5086) with WEDM is studied. The four control parameter were selected i.e pulse on time (TON), pulse off time (TOFF), peak current (IP), and spark gap voltage (SV) to investigate their effects on material removal rate (MRR). Each control parameter had three levels. Total 27 experiments were done with a zinc coated brass wire of diameter 0.25 mm. Taguchi L9 orthogonal array technique was used for the experiment. ANOVA was used to find out the significance of control parameters and their contribution on MRR. It was found that maximum material removal rate was 41.52 mm3 /min which was due to high pulse on time and low pulse off time.

Effect of WEDM process parameters on machinability of Nimonic75 alloy using brass wire

2020 ◽  
Vol 17 (3) ◽  
pp. 389-397
Author(s):  
Harvinder Singh ◽  
Vinod Kumar ◽  
Jatinder Kapoor
Keyword(s):  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Cutting Speed ◽  
Content Type ◽  
Response Characteristics ◽  
Nickel Based Alloy ◽  
Pulse On Time ◽  
Pulse Off Time

Purpose This study aims to investigate the influence of process parameters of wire electrical discharge machining (WEDM) of Nimonic75. Nimonic75 is a Nickel-based alloy mostly used in the aerospace industry for its strength at high temperature. Design/methodology/approach One factor at a time (OFAT) approach has been used to perform the experiments. Pulse on time, pulse off time, peak current and servo voltage were chosen as input process parameters. Cutting speed, material removal rate and surface roughness (Ra) were selected as output performance characteristics. Findings Through experimental work, the effect of process parameters on the response characteristics has been found. Results identified the most important parameters to maximize the cutting speed and material removal rate and minimize Ra. Originality/value Very limited research work has been done on WEDM of Nickel-based alloy Nimonic75. Therefore, the aim of this paper to conduct preliminary experimentation for identifying the parameters, which influence the response characteristics such as material removal rate, cutting speed, Ra, etc. during WEDM of Nickel-based alloy (Nimonic75) using OFAT approach and found the machinability of Nimonic75 for further exhaustive experimentation work.

Optimization of Electric Discharge Machining Parameters of Al-7%Si-4%Mg with 20% of Red Mud Metal Matrix Composites

2014 ◽  
Vol 941-944 ◽  
pp. 1973-1976
Author(s):  
B. Geetha ◽  
K. Ganesan
Keyword(s):  
Surface Roughness ◽  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electric Discharge ◽  
Material Removal ◽  
Removal Rate ◽  
Tool Wear Rate ◽  
Peak Current ◽  
Pulse On Time

An investigation was carried out to find out the influence of process parameters on surface roughness (SR) and material removal rate (MRR) in electric discharge machine of Al-7%Si-4%Mg with 20% of red mud Metal Matrix Composites since electric discharge machining is a thermo-electric machining process, an electronic die sinking electric discharge machine was used to drill holes in the composite work piece, copper is used as tool material. Experiment was carried out to find surface roughness, material removal rate and tool wear rate by varying the peak current, flushing pressure of dielectric fluid and pulse on time. It was found that the surface roughness of composite metal increases with the increase peak current ,pulse on time and flushing pressure due larger and deeper craters on the drilled surface. It was also found that there was increase in metal removal rate with the increase in peak current and flushing pressure and slightly decreases with the increase in pulse on time due carbon deposits on the electrodes. Experimental analysis is carried using Taguchi’s Design of Experiment method with various parameters like peak current, flushing pressure of dielectric fluid and pulse on time to identify the key factors that influence the surface roughness, material removal rate and tool wear rate. It was found that the peak current was the most significant parameter that influences surface roughness, material removal rate and tool wear rate. The Taguchi experiments results confirm the actual results obtained from the numerical calculation.

Statistical analysis of material removal rate and surface roughness in electrical discharge turning of titanium alloy (Ti-6Al-4V)

2016 ◽  
Vol 232 (9) ◽  
pp. 1603-1614 ◽  
Author(s):  
Vikas Gohil ◽  
Yogesh M Puri
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Machining Parameters ◽  
Peak Current ◽  
Pulse On Time

Electrical discharge turning is a unique form of electrical discharge machining process, which is being especially developed to generate cylindrical forms and helical profiles on the difficult-to-machine materials at both macro and micro levels. A precise submerged rotating spindle as a work holding system was designed and added to a conventional electrical discharge machine to rotate the workpiece. A conductive preshaped strip of copper as a forming tool is fed (reciprocate) continuously against the rotating workpiece; thus, mirror image of the tool is formed on the circumference of the workpiece. The machining performance of electrical discharge turning process is defined and influenced by its machining parameters, which directly affects the quality of the machined component. This study presents an investigation on the effects of the machining parameters, namely, pulse-on time, peak current, gap voltage, spindle speed and flushing pressure, on the material removal rate (MRR) and surface roughness (Ra) in electrical discharge turning of titanium alloy Ti-6Al-4V. This has been done by means of Taguchi’s design of experiment technique. Analysis of variance as well as regression analysis is performed on the experimental data. The signal-to-noise ratio analysis is employed to find the optimal condition. The experimental results indicate that peak current, gap voltage and pulse-on time are the most significant influencing parameters that contribute more than 90% to material removal rate. In the context of Ra, peak current and pulse-on time come up with more than 82% of contribution. Finally, the obtained predicted optimal results were verified experimentally. It was shown that the error values are all less than 6%, confirming the feasibility and effectiveness of the adopted approach.

scholarly journals MRR - Performance on EDM Drilling over Nano Composite Material

2019 ◽  
Vol 8 (4) ◽  
pp. 12340-12345
Keyword(s):  
Composite Material ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Performance Measure ◽  
Peak Current ◽  
Multi Wall Carbon Nanotubes ◽  
Main Effect ◽  
Pulse On Time ◽  
Pulse Off Time

Now a day’s more research works are going on performance of MRR on various operations with respect to EDM machining. This research paper is to focus the same on parameters base with Performance measure of Material Removal Rate (MRR) in composite Material (Aluminum, Boron Carbide and Multi Wall Carbon NanoTubes (MWCNT) .The machine used for this research is Sink EDM with drilling operation. .Lots of statistical techniques are available to predict the accurate and reliable result form the research data. Here the Minitab 16 software is used to analyze the MRR performance. The input parameters selected for the EDM machine are: Pulse on time, pulse off time and voltage. The results were compared with the DOE-Taguchi approach (L9) Orthogonal array - result. [1] .Material Removal Rate was studied along with S/N ratio of Main effect plot, Means and Interaction Plot.[2] From software the main effect plots, residual plots, S/N ratio interaction plots and means was obtained The rapid increase with pulse on for MRR is resulted due to addition of nano powder and linearly increase with peak current. The optimal parameters combination was determined as CNT (1%), Pulse on (10 µs), Pulse off (2.5 µs) and Peak Current (50A) i.e. 1 4 4 2. The experimental results were checked with predicted results and a positive agreement was found. Comparing old studies the optimization values found by this experiment results with more MRR.

Sign in / Sign up

Export Citation Format

Share Document