Research on Failure Mechanism for Distributed Drive Vehicle Based on Co-simulation of Carsim and Matlab

2020 ◽  
Author(s):  
Li Gang ◽  
Ge Pingshu ◽  
Zhang Jiaqi ◽  
Zhang Tao ◽  
Zhao Kailan ◽  
...  
Keyword(s):  
Failure Mechanism

On the role of tin underlays for the prevention of thermal grooving in thin gold films

1986 ◽  
Vol 44 ◽  
pp. 732-733
Author(s):  
Jin Young Kim ◽  
R. E. Hummel ◽  
R. T. DeHoff
Keyword(s):  
Thin Film ◽  
Free Surface ◽  
Grain Boundary ◽  
Beneficial Effect ◽  
Failure Mechanism ◽  
Failure Mechanisms ◽  
Distinct Advantage ◽  
Gold Films ◽  
Gold Thin Film

Gold thin film metallizations in microelectronic circuits have a distinct advantage over those consisting of aluminum because they are less susceptible to electromigration. When electromigration is no longer the principal failure mechanism, other failure mechanisms caused by d.c. stressing might become important. In gold thin-film metallizations, grain boundary grooving is the principal failure mechanism.Previous studies have shown that grain boundary grooving in gold films can be prevented by an indium underlay between the substrate and gold. The beneficial effect of the In/Au composite film is mainly due to roughening of the surface of the gold films, redistribution of indium on the gold films and formation of In2O3 on the free surface and along the grain boundaries of the gold films during air annealing.

Influence of Air Entrappment on Flood Embankment Failure Mechanism - Model Tests

2008 ◽  
Vol 11 (-1) ◽  
pp. 188-201 ◽  
Author(s):  
Piotr Bogacz ◽  
Jarosława Kaczmarek ◽  
Danuta Leśniewska
Keyword(s):  
Failure Mechanism ◽  
Model Tests ◽  
Mechanism Model

Application of Lock-in Thermography on PCB for Fault Localization and Validation of Failure Mechanism Due to External Discrete Component Variation

2010 ◽  
Author(s):  
William Ng ◽  
Kevin Weaver ◽  
Zachary Gemmill ◽  
Herve Deslandes ◽  
Rudolf Schlangen
Keyword(s):  
Failure Mechanism ◽  
Integrated Circuit ◽  
Printed Circuit Board ◽  
Hot Spot ◽  
Circuit Board ◽  
Discrete Component ◽  
Printed Circuit ◽  
Thermal Signature ◽  
Lock In

Abstract This paper demonstrates the use of a real time lock-in thermography (LIT) system to non-destructively characterize thermal events prior to the failing of an integrated circuit (IC) device. A case study using a packaged IC mounted on printed circuit board (PCB) is presented. The result validated the failing model by observing the thermal signature on the package. Subsequent analysis from the backside of the IC identified a hot spot in internal circuitry sensitive to varying value of external discrete component (inductor) on PCB.

Case Study in Fault Isolation of a Metal Short for Yield Enhancement

2010 ◽  
Author(s):  
Sarven Ipek ◽  
David Grosjean
Keyword(s):  
Failure Analysis ◽  
Failure Mechanism ◽  
Photon Emission ◽  
Fault Isolation ◽  
Yield Enhancement ◽  
Analysis Technique ◽  
Laser Signal ◽  
Signal Injection ◽  
Microscopy Techniques

Abstract The application of an individual failure analysis technique rarely provides the failure mechanism. More typically, the results of numerous techniques need to be combined and considered to locate and verify the correct failure mechanism. This paper describes a particular case in which different microscopy techniques (photon emission, laser signal injection, and current imaging) gave clues to the problem, which then needed to be combined with manual probing and a thorough understanding of the circuit to locate the defect. By combining probing of that circuit block with the mapping and emission results, the authors were able to understand the photon emission spots and the laser signal injection microscopy (LSIM) signatures to be effects of the defect. It also helped them narrow down the search for the defect so that LSIM on a small part of the circuit could lead to the actual defect.

Unique Autoclave Stress Induced Failure Mechanism

2005 ◽  
Author(s):  
John Butchko ◽  
Bruce T. Gillette
Keyword(s):  
Corrosion Rate ◽  
Grain Boundary ◽  
Failure Analysis ◽  
Failure Mechanism ◽  
Metal Corrosion ◽  
Corrosion Mechanism ◽  
Reliability Testing ◽  
Process Change ◽  
Transistor Reliability ◽  
Pass Through

Abstract Autoclave Stress failures were encountered at the 96 hour read during transistor reliability testing. A unique metal corrosion mechanism was found during the failure analysis, which was creating a contamination path to the drain source junction, resulting in high Idss and Igss leakage. The Al(Si) top metal was oxidizing along the grain boundaries at a faster rate than at the surface. There was subsurface blistering of the Al(Si), along with the grain boundary corrosion. This blistering was creating a contamination path from the package to the Si surface. Several variations in the metal stack were evaluated to better understand the cause of the failures and to provide a process solution. The prevention of intergranular metal corrosion and subsurface blistering during autoclave testing required a materials change from Al(Si) to Al(Si)(Cu). This change resulted in a reduced corrosion rate and consequently prevented Si contamination due to blistering. The process change resulted in a successful pass through the autoclave testing.

The Use of TMAH to Etch Silicon and Expose Metal Bridging Failures

2000 ◽  
Author(s):  
Mark Morris ◽  
James Mohr ◽  
Esteban Ortiz ◽  
Steven Englebretson
Keyword(s):  
Failure Mechanism ◽  
Schottky Diodes ◽  
Tetramethylammonium Hydroxide ◽  
Novel Approach ◽  
Failure Location ◽  
Metal Etching ◽  
Plastic Mold

Abstract Determination of metal bridging failures on plastic encapsulated devices is difficult due to the metal etching effects that occur while removing many of the plastic mold compounds. Typically, the acids used to remove the encapsulation are corrosive to the metals that are found within the device. Thus, decapsulation can result in removal of the failure mechanism. Mechanical techniques are often not successful due to damage that results in destruction of the die and failure mechanism. This paper discusses a novel approach to these types of failures using a silicon etch and a backside evaluation. The desirable characteristics of the technique would be to remove the silicon and leave typical device metals unaffected. It would also be preferable that the device passivation and oxides not be etched so that the failure location is not disturbed. The use of Tetramethylammonium Hydroxide (TMAH), was found to fit these prerequisites. The technique was tested on clip attached Schottky diodes that exhibited resistive shorting. The use of the TMAH technique was successful at exposing thin solder bridges that extruded over the edge of the die resulting in failure.

Electromigration and Electrochemical Reaction Mixed Failure Mechanism in Gold Interconnection System

1999 ◽  
Author(s):  
Hide Murayama ◽  
Makoto Yamazaki ◽  
Shigeru Nakajima
Keyword(s):  
Failure Mechanism ◽  
Failure Rate ◽  
Electrochemical Reaction ◽  
Dielectric Films ◽  
Failure Rates ◽  
Interlayer Dielectric ◽  
Bipolar Devices ◽  
Gold Metallization

Abstract Power bipolar devices with gold metallization experience high failure rates. The failures are characterized as shorts, detected during LSI testing at burn-in. Many of these shorted locations are the same for the failed devices. From a statistical lot analysis, it is found that the short failure rate is higher for devices with thinner interlayer dielectric films. Based upon these results, a new electromigration and electrochemical reaction mixed failure mechanism is proposed for the failure.

Investigation of High Frequency Failures on a 0.35μm CMOS IC

1999 ◽  
Author(s):  
Alan Kennen ◽  
John F. Guravage ◽  
Lauren Foster ◽  
John Kornblum
Keyword(s):  
Failure Analysis ◽  
Failure Mechanism ◽  
Integrated Circuit ◽  
Metal Layer ◽  
Ion Beam ◽  
Stress Test ◽  
Design For Test ◽  
Interface Failure ◽  
Serial Interface ◽  
High Impedance

Abstract Rapidly changing technology highlights the necessity of developing new failure analysis methodologies. This paper will discuss the combination of two techniques, Design for Test (DFT) and Focused Ion Beam (FIB) analysis, as a means for successfully isolating and identifying a series of high impedance failure sites in a 0.35 μm CMOS design. Although DFT was designed for production testing, the failure mechanism discussed in this paper may not have been isolated without this technique. The device of interest is a mixed signal integrated circuit that provides a digital up-convert function and quadrature modulation. The majority of the circuit functions are digital and as such the majority of the die area is digital. For this analysis, Built In Self Test (BIST) circuitry, an evaluation board for bench testing and FIB techniques were used to successfully identify an unusual failure mechanism. Samples were subjected to Highly Accelerated Stress Test (HAST) as part of the device qualification effort. Post-HAST electrical testing at 200MHz indicated that two units were non-functional. Several different functional blocks on the chip failed electrical testing. One part of the circuitry that failed was the serial interface. The failure analysis team decided to look at the serial interface failure mode first because of the simplicity of the test. After thorough analysis the FA team discovered increasing the data setup time at the serial port input allowed the device to work properly. SEM and FIB techniques were performed which identified a high impedance connection between a metal layer and the underlying via layer. The circuit was modified using a FIB edit, after which all vectors were read back correctly, without the additional set-up time.

Sign in / Sign up

Export Citation Format

Share Document