A comparitive study of youla and PID control algorithms for regulation of output voltage of Buck converter

2014 ◽  
Author(s):  
Nivedita Pati
Keyword(s):  
Pid Control ◽  
Output Voltage ◽  
Buck Converter ◽  
Control Algorithms

Research of Practical Solar Energy Intelligent Regulated Power Supply

2013 ◽  
Vol 385-386 ◽  
pp. 1189-1192
Author(s):  
Hong Li Cheng ◽  
Wei Zhang ◽  
Geng Chuan Zhang
Keyword(s):  
Pid Control ◽  
Output Voltage ◽  
High Efficiency ◽  
Abrupt Change ◽  
Low Voltage ◽  
Buck Converter ◽  
Fuzzy Pid ◽  
Fuzzy Pid Control ◽  
Circuit Structure ◽  
Solar Powered

A solar-powered fuzzy PID control based DC/DC series the LDO method is suggested to take advantage of the performance of the DC/DC converter high efficiency while reduce the output ripple and low voltage is continuously adjustable. Fuzzy PID control according to the error of sampling the output voltage and the desired output voltage, the DC/DC output and LDO output with constant pressure difference control. The circuit structure, the dynamic response of output voltage in the process of abrupt change of load and starting is analyzed. Parameter selection and design considerations are given. A BUCK converter is used as an example to show the design steps. Simulation study are made on the supply, the results of which show that method is feasible

scholarly journals Analysis and Design for Output Voltage Regulation in Constant-on-Time-Controlled Fly-Buck Converter

Electronics ◽  
2021 ◽  
Vol 10 (16) ◽  
pp. 1886
Author(s):  
Younghoon Cho ◽  
Paul Jang
Keyword(s):  
Output Voltage ◽  
Voltage Regulation ◽  
Design Guidelines ◽  
Buck Converter ◽  
Design Guideline ◽  
Analysis And Design ◽  
Flyback Converter ◽  
Auxiliary Power ◽  
Primary Output ◽  
Output Capacitor

Fly-buck converter is a multi-output converter with the structure of a synchronous buck converter structure on the primary side and a flyback converter structure on the secondary side, and can be utilized in various applications due to its many advantages. In terms of control, the primary side of the fly-buck converter has the same structure as a synchronous buck converter, allowing the constant-on-time (COT) control to be applied to the fly-buck converter. However, due to the inherent energy transfer principle, the primary-side output voltage regulation of COT controlled fly-buck converters may be poor, which can deteriorate the overall converter performance. Therefore, the primary output capacitor must be carefully designed to improve the voltage regulation characteristics. In this paper, a theoretical analysis of the output voltage regulation in COT controlled fly-buck converter is conducted, and based on this, a design guideline for the primary output capacitor considering the output voltage regulation is presented. The validity of the analysis and design guidelines was verified using a 5 W prototype of the COT controlled fly-buck converter for telecommunication auxiliary power supply.

scholarly journals Smooth Tracking Trajectory Generation of Large Antenna

2016 ◽  
Vol 53 (1) ◽  
pp. 24-33 ◽  
Author(s):  
S. Upnere ◽  
N. Jekabsons ◽  
U. Locans
Keyword(s):  
Pid Control ◽  
Control Algorithm ◽  
Case Analysis ◽  
Control Algorithms ◽  
Control Methods ◽  
Antenna Feed ◽  
Feed Forward Control ◽  
Order Polynomial ◽  
Smooth Tracking ◽  
Tracking Trajectory

Abstract The current paper presents an engineering approach for studies of the control algorithm designed for a mechanically robust large antenna. Feed-forward control methods with the 3rd-order polynomial tracking algorithm are supplemented to the original feed-back PID control system. Dynamical model of the existing servo system of 32m radio telescope has been developed to widen a case analysis of observation sessions and efficiency of the control algorithms due to limited access to an antenna. Algorithms along with the results from the system implemented on a real antenna as well as model results are presented.

scholarly journals Fuzzy Logic Based Controller For Buck Converter

2019 ◽  
Vol 1 (3) ◽  
pp. 1-12
Author(s):  
Habibullah Salim ◽  
Irma Husnaini ◽  
Asnil Asnil
Keyword(s):  
Fuzzy Logic ◽  
Solar Cell ◽  
Output Voltage ◽  
Fuzzy Logic Controller ◽  
Pulse Generation ◽  
Buck Converter ◽  
Dc Voltage ◽  
Generation Technique ◽  
Fuzzy Logic Method ◽  
The Stability

This research aims to make buck converter prototype for PLTS system by using fuzzy logic controller. Buck converter is required in the PLTS system if the required unidirectional voltage is smaller than the output voltage of the solar cell. Buck converter used to convert 24 Volt dc voltage to 12 Volt dc with 60 watt capability. While fuzzy logic controller is used to improve buck converter performance based on pulse generation technique for switching. The application of fuzzy logic method is expected to improve the performance of the system by maintaining the stability of buck converter output voltage of 12 volts and reduce the output ripple value. Atmega8535 microcontroller is used to generate PWM pulses for switching on power circuits. The results obtained from the test using a 100 Ohm 5 Watt load obtained the buck converter output voltage of 12.4 Volt.

scholarly journals Novel Step-Down DC–DC Converters Based on the Inductor–Diode and Inductor–Capacitor–Diode Structures in a Two-Stage Buck Converter

Energies ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 1131 ◽  
Author(s):  
Mauricio Dalla Vecchia ◽  
Giel Van den Broeck ◽  
Simon Ravyts ◽  
Johan Driesen
Keyword(s):  
Output Voltage ◽  
Buck Converter ◽  
Switching Frequency ◽  
Two Stage ◽  
Voltage Level ◽  
Multiple Strategies ◽  
Power Electronics Converters ◽  
Load Demand ◽  
Duty Cycles ◽  
Step Down

This paper explores and presents the application of the Inductor–Diode and Inductor-Capacitor-Diode structures in a DC–DC step-down configuration for systems that require voltage adjustments. DC micro/picogrids are becoming more popular nowadays and the study of power electronics converters to supply the load demand in different voltage levels is required. Multiple strategies to step-down voltages are proposed based on different approaches, e.g., high-frequency transformer and voltage multiplier/divider cells. The key question that motivates the research is the investigation of the aforementioned Inductor–Diode and Inductor–Capacitor–Diode, current multiplier/divider cells, in a step-down application. The two-stage buck converter is used as a study case to achieve the output voltage required. To extend the intermediate voltage level flexibility in the two-stage buck converter, a second switch was implemented replacing a diode, which gives an extra degree-of-freedom for the topology. Based on this modification, three regions of operation are theoretically defined, depending on the operational duty cycles δ2 and δ1 of switches S2 and S1. The intermediate and output voltage levels are defined based on the choice of the region of operation and are mapped herein, summarizing the possible voltage levels achieved by each configuration. The paper presents the theoretical analysis, simulation, implementation and experimental validation of a converter with the following specifications; 48 V/12 V input-to-output voltage, different intermediate voltage levels, 100 W power rating, and switching frequency of 300 kHz. Comparisons between mathematical, simulation, and experimental results are made with the objective of validating the statements herein introduced.

scholarly journals A Low EMI DC-DC Buck Converter with a Triangular Spread-Spectrum Mechanism

Energies ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 856
Author(s):  
Jing-Yuan Lin ◽  
Yi-Chieh Hsu ◽  
Yo-Da Lin
Keyword(s):  
Spread Spectrum ◽  
Electromagnetic Interference ◽  
Output Voltage ◽  
Buck Converter ◽  
Circuit Board ◽  
System Stability ◽  
Maximum Efficiency ◽  
Load Current ◽  
Voltage Range ◽  
Switching Regulators

In this paper, a triangular spread-spectrum mechanism is proposed to suppress the electromagnetic interference (EMI) of a DC-DC buck converter. The proposed triangular spread-spectrum mechanism, which is implemented in the chip, can avoid modifying the printed circuit board of switching regulators. In addition, a lower ripple of output voltage of switching regulators and a better system stability can be realized by the inductive DC resistance (DCR) current sensing circuit. The chip is fabricated by using TSMC 0.18-μm 1P6M CMOS technology. The chip area including PADs is 1.2 × 1.15 mm2. The input voltage range is 2.7~3.3 V and the output voltage is 1.8 V. The maximum load current is 700 mA. The off-chip inductor and capacitor are 3.3 μH and 10 μF, respectively. The experimental results demonstrate that the maximum spur of the proposed DC-DC buck converter with the triangular spread-spectrum mechanism improves to 14dBm. Moreover, the transient recovery time of step-up and step-down loads are both 5 μs. The measured maximum efficiency is 94% when the load current is 200 mA.

Sign in / Sign up

Export Citation Format

Share Document