An accurate electrical model for atmospheric pressure DBD plasma in air with experimental validation

Author(s):  
Vishal Jain ◽  
R. Srinivasan ◽  
Vivek Agarwal
2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Grittima Kongprawes ◽  
Doonyapong Wongsawaeng ◽  
Kanokwan Ngaosuwan ◽  
Worapon Kiatkittipong ◽  
Suttichai Assabumrungrat

AbstractPartially hydrogenated fatty acid methyl ester (H-FAME) is conventionally produced through partial hydrogenation under high pressure and elevated temperature in the presence of a catalyst. Herein, a novel green, catalyst-free, non-thermal and atmospheric pressure dielectric barrier discharge (DBD) plasma was employed instead of a conventional method to hydrogenate palm FAME. H-FAME became more saturated with the conversion of C18:2 and C18:3 of 47.4 and 100%, respectively, at 100 W input power, 1 mm gas-filled gap size and 80% H2 in the mixed gas at room temperature for 5 h, causing a reduction of the iodine value from 50.2 to 43.5. Oxidation stability increased from 12.8 to 20 h while a cloud point changed from 13.5 to 16 °C. Interestingly, DBD plasma hydrogenation resulted in no trans-fatty acid formation which provided a positive effect on the cloud point. This green DBD plasma system showed a superior performance to a conventional catalytic reaction. It is an alternative method that is safe from explosion due to the mild operating condition, as well as being highly environmentally friendly by reducing waste and energy utilization from the regeneration process required for a catalytic process. This novel green plasma hydrogenation technique could also be applied to other liquid-based processes.


2008 ◽  
Vol 202 (24) ◽  
pp. 6029-6033 ◽  
Author(s):  
Min Xi ◽  
Yu-Liang Li ◽  
Shu-yong Shang ◽  
Dai-Hong Li ◽  
Yong-Xiang Yin ◽  
...  

Author(s):  
Takehiko Segawa ◽  
Hiro Yoshida ◽  
Shinya Takekawa ◽  
Timothy Jukes ◽  
Kwing-So Choi

Properties of coaxial annular jets produced by a dielectric barrier discharge (DBD) plasma actuator with a doughnut shaped electrodes were investigated under atmospheric pressure and room temperature. The actuator consists of two circular electrodes sandwiching a thin dielectric layer. By applying 0 – ±3.3 kV between the electrodes at radio frequencies, the plasma jet is formed near the inner edge of the top electrode. The radial jet runs toward the center of the electrode and then impinges at the center to generate a wall normal annular jet. The evolution of the wall normal jet was observed precisely using particle image velocimetry (PIV) system. It was found that characteristic velocities increase in proportion to the bursting frequency and inversely proportional to the inner diameter of the electrode at the surging time of the voltage at 5.0 × 10−6sec.


2009 ◽  
Vol 37 (1) ◽  
pp. 128-134 ◽  
Author(s):  
Allan Flores-Fuentes ◽  
Rosendo Pena-Eguiluz ◽  
RÉgulo Lopez-Callejas ◽  
Antonio Mercado-Cabrera ◽  
RaÚl Valencia-Alvarado ◽  
...  

Holzforschung ◽  
2018 ◽  
Vol 72 (11) ◽  
pp. 979-991 ◽  
Author(s):  
Jure Žigon ◽  
Marko Petrič ◽  
Sebastian Dahle

AbstractThe treatment of wood surfaces with gas discharges is one of the methods to achieve better surface adhesion properties. Good penetration, spreading and wettability of the applied liquid adhesives and coatings is a crucial factor for their adequate mechanical properties. Plasmas are the result of electrical discharge and can be created in different ways. The plasma treatment (PT) is frequently executed prior to material bonding or coating via the so-called dielectric barrier discharges (DBD) at atmospheric pressure. This literature review summarizes the essential aspects of DBD PTs aiming at a better wettability and surface adhesion. After introduction of the principle of DBD, the individual effects of internal and external parameters of the process will be discussed, which influence the final properties of treated materials.


2018 ◽  
Vol 20 (6) ◽  
pp. 1199-1204 ◽  
Author(s):  
M. Borić ◽  
H. Puliyalil ◽  
U. Novak ◽  
B. Likozar

Atmospheric-pressure DBD plasma was used as a methodology for intensified protein removal from crustacean shell waste.


2010 ◽  
Vol 42 ◽  
pp. 228-231 ◽  
Author(s):  
Yan Zhang ◽  
Yin Ding Lv

In this paper, polypropylene (PP) melt blown non-woven fabric is treated by atmospheric pressure N2 or N2/CO2 dielectric barrier discharge (DBD) plasma. The variation of the surface hydrophilicity of PP sample is experimentally investigated by surface water contact angle, Fourier transform infrared reflectance spectroscopy (FTIR-ATR). The results show that the hydrophilicity of PP sample is considerably improved as long as the very short plasma treatment time (several seconds). However, the treatment effect of atmospheric N2/CO2 plasma is worse than that of atmospheric N2 plasma.


2008 ◽  
Vol 36 (4) ◽  
pp. 1352-1353 ◽  
Author(s):  
Gui-Min Xu ◽  
Yue Ma ◽  
Guan-Jun Zhang

2004 ◽  
Vol 29 (2) ◽  
pp. 173-180 ◽  
Author(s):  
N. Naudé ◽  
J.-P. Cambronne ◽  
N. Gherardi ◽  
F. Massines

Sign in / Sign up

Export Citation Format

Share Document