Thermally induced wrinkling of poly-L-lactic acid with palladium nanolayers

Author(s):  
Petr Jurik ◽  
Iva Michaljanicova ◽  
Zdenka Novotna ◽  
Petr Slepicka ◽  
Vaclav Svorcik ◽  
...  
2018 ◽  
Vol 33 (4) ◽  
pp. 397-415 ◽  
Author(s):  
Harish Chinnasami ◽  
Jeff Gimble ◽  
Ram V Devireddy

Thermally induced phase separation method was used to make porous three-dimensional poly (l-lactic acid) scaffolds. The effect of imposed thermal profile during freezing of the poly (l-lactic acid) in dioxane solution on the scaffold was characterized by their micro-structure, porosity (%), pore sizes’ distribution, and mechanical strength. The porosity (%) decreased considerably with increasing concentrations of poly (l-lactic acid) in the solution, while a decreasing trend was observed with increasing cooling rates. The mechanical strength increases with increase in poly (l-lactic acid) concentration and also with increase in the cooling rate for both types of solvents. Therefore, mechanical strength was increased by higher cooling rates while the porosity (%) remained relatively consistent. Scaffolds made using higher concentrations of poly (l-lactic acid; 7% and 10% w/v) in solvent showed better mechanical strength which improved relatively with increasing cooling rates (1°C–40°C/min). This phenomenon of enhanced structural integrity with increasing cooling rates was more prominent in scaffolds made from higher initial poly (l-lactic acid) concentrations. Human adipose–derived stem cells were cultured on these scaffold (7% and 10% w/v) prepared by thermally induced phase separation at all cooling rates to measure the cell proliferation efficiency as a function of their micro-structural properties. Mean pore sizes played a crucial role in cell proliferation than percent porosity since all scaffolds were >88% porous. The viability percent of human adipose tissue–derived adult stem cells increased consistently with longer periods of culture. Thus, poly (l-lactic acid) scaffolds prepared by thermally controlled thermally induced phase separation method could be a prime candidate for making ex vivo tissue-engineered grafts for surgical implantation.


2008 ◽  
Vol 16 (9) ◽  
pp. 597-604 ◽  
Author(s):  
Wang Ning ◽  
Zhang Xingxiang ◽  
Yu Jiugao ◽  
Fang Jianming

Poly(lactic acid) (PLA) is a biodegradable thermoplastic that can be produced from renewable resources, and so was considered as a major alternative to petroleum-based plastics for packaging applications. However, plasticisation of PLA was required in order to obtain films with sufficient flexibility. Poly(1, 3-butylene adipate) (PBA) was used as a novel plasticiser for PLA, and acetyltributyl citrate (ATBC) was used as the control. FTIR revealed that interaction took place between PLA and plasticiser. With an increasing plasticiser content, storage modulus and glass transition temperature decreased, but elongation at break increased. The elongation at break of PBA-plasticised PLA (PBA content 30 wt.%) could be above 600%, higher than that of ATBC-plasticised PLA (ATBC content 30 wt.%). Moreover, PBA was able to restrain thermally induced migration of plasticiser in plasticised PLA. It was also found that the migration rate of ATBC was directly proportional to the ATBC content in the blends. The rheology showed that the plasticiser could obviously decrease the shear viscosity and improve the fluidity of the blends. PBA was therefore recognised as a novel plasticiser for enhancing the properties of PLA. In particular, as a biodegradable polymer, PBA, when used as a plasticiser in PLA, can enhance migration resistance for its proper molecular weight. Moreover, the area of application of plasticised PLA is broadened.


2018 ◽  
Vol 2 (2) ◽  
pp. 313-322 ◽  
Author(s):  
Hailiang Mao ◽  
Chen Wang ◽  
Xiaohua Chang ◽  
Heqing Cao ◽  
Guorong Shan ◽  
...  

A novel thermogel exhibiting unique thermally-induced gel–sol–gel multiple phase transitions was obtained by controlling the compositions of PLA/PEG copolymers.


1984 ◽  
Vol 56 (5) ◽  
pp. 1302-1307 ◽  
Author(s):  
T. C. Boysen ◽  
S. Yanagawa ◽  
F. Sato ◽  
K. Sato

In an attempt to devise a method for collecting large volumes of thermally induced sweat with less epidermal contamination and evaporative water loss, we developed an anaerobic sweat collector by using a sheet of polyethylene film placed over a thin layer of Vaseline and paraffin oil on the skin. To test the validity of the new method, sweat samples collected every 5 min from the new collector (sweat A) were compared with those obtained from a second collector using no oil (sweat B) and scraped sweat for concentrations of adenosine 3′,5′-cyclic monophosphate (cAMP), protein, glucose, urea, lactic acid, calcium, sodium, potassium, and cholesterol. The concentration of sweat ingredients in scraped sweat was often far greater than could be expected from evaporative water loss alone. When compared with sweat A, sweat B also had higher concentrations of these ingredients in the initial samples, indicating epidermal contamination, which was especially marked in cAMP, protein, urea, cholesterol, and calcium. Concomitant with a rise in plasma glucose following the administration of a glucose bolus, the sweat glucose significantly increased, indicating the plasma as a major source of sweat glucose. We conclude that the new sweat collector is instrumental in collecting large volumes of the cleanest possible human sweat.


2005 ◽  
Vol 04 (04) ◽  
pp. 517-523
Author(s):  
WENJIAN WENG ◽  
YANBO GAO ◽  
LILI PAN ◽  
YANBAO LI ◽  
PIYI DU ◽  
...  

Biodegradable porous materials can serve as a scaffold in tissue engineering. In this work, highly porous nano-calcium phosphate (NCP)/poly(L-lactic acid)(PLLA) composites were prepared by a thermally induced phase separation technique. Five calcium phosphates with different biodegradation rate were selected, i.e. amorphous calcium phosphate, α-tricalcium phosphate, β-tricalcium phosphate and biphasic α/β-tricalcium phosphate. The results showed that the NCP particles could be homogenously incorporated into pore walls; the composites had a porosity of ~90%, and a pore size of ~200 μm. From the point of view of materials science, the obtained porous NCP/PLLA composites demonstrate to have a capability of applying in bone tissue engineering.


Sign in / Sign up

Export Citation Format

Share Document