high power LED heat dissipation simulation analysis via heat sink fin variation

2014 ◽  
Author(s):  
V. Retnasamy ◽  
Z. Sauli ◽  
R. Vairavan ◽  
S. Taniselass ◽  
H. Mamat
Keyword(s):  
High Power ◽  
Heat Sink ◽  
Heat Dissipation ◽  
Simulation Analysis ◽  
High Power Led

Heat Dissipation Analysis of High Power LED Connected to Copper Coated Heat Sink by Soldering

2011 ◽  
Vol 32 (11) ◽  
pp. 1171-1175 ◽  
Author(s):  
柴伟伟 CHAI Wei-wei ◽  
陈清华 CHEN Qing-hua ◽  
李琳红 LI Ling-hong ◽  
唐文勇 TANG Wen-yong ◽  
张学清 ZHANG Xue-qing ◽  
...  
Keyword(s):  
High Power ◽  
Heat Sink ◽  
Heat Dissipation ◽  
High Power Led

Heat Dissipation Simulation Analysis of High Power LED via Heat Slug Geometry Variation

2014 ◽  
Vol 1082 ◽  
pp. 344-347
Author(s):  
Vithyacharan Retnasamy ◽  
Zaliman Sauli ◽  
Rajendaran Vairavan ◽  
Hussin Kamarudin ◽  
Mukhzeer Mohamad Shahimin ◽  
...  
Keyword(s):  
High Power ◽  
Heat Dissipation ◽  
Simulation Analysis ◽  
Life Time ◽  
Junction Temperature ◽  
Von Mises Stress ◽  
Potential Development ◽  
High Power Led ◽  
Superior Surface ◽  
Von Mises

High power LEDs are currently being plagued by heat dissipation challenges due to its high power density thus limiting its further potential development and fulfillment. Exercising proper selection of packaging component could improve the life time of high power LED. In this work, the significance of the heat slug geometry on the heat dissipation of high power LED was addressed through simulation analysis. The heat slug geometries were varied in order to compare the heat dissipation of the high power LED. Ansys version 11 was utilized for the simulation. The heat dissipation of the high power LED was evaluated in terms of junction temperature, von Mises stress and thermal resistance. The key results of the analysis showed that a superior surface area is preferred for an enhanced heat dissipation of high power LED

Thermal Simulation Analysis of High Power LED with Varied Heat Sink Fin Design

2014 ◽  
Vol 1082 ◽  
pp. 332-335
Author(s):  
Vithyacharan Retnasamy ◽  
Zaliman Sauli ◽  
Hussin Kamarudin ◽  
Muammar Mohamad Isa ◽  
Gan Meng Kuan
Keyword(s):  
High Power ◽  
Heat Sink ◽  
Simulation Analysis ◽  
Input Power ◽  
Junction Temperature ◽  
Single Chip ◽  
Pin Fin ◽  
High Power Led ◽  
Different Shapes ◽  
Fin Design

In this paper, the heat distribution for single chip high power LED package attached with varied heat sink fin shapes were analyzed through simulation. The main focus of this study was to scrutinize the fluctuation of junction temperature with different shapes of heat sink fin designs. The simulation was done using Ansys version 11. The single chip LED was loaded with input power of 0.5 W and 1 W . Simulation was done at ambient temperature of 25°C under three convection coefficient of 5, 10 and 15 W/m2.oC respectively. The obtained results showed that the LED package with pyramid pin fin heat sink has demonstrated a better thermal performance compared to the LED package with cylindrical pin fin heat sink.

scholarly journals Finite Element Simulation of the Machining Process of Boiling Structures in a Novel Radial Heat Sink for High-Power LEDs

Materials ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 3958
Author(s):  
Jianhua Xiang ◽  
Zeyu Liu ◽  
Chunliang Zhang ◽  
Chao Zhou ◽  
Conggui Chen
Keyword(s):  
Heat Transfer ◽  
Plastic Deformation ◽  
Finite Element ◽  
Phase Change ◽  
High Power ◽  
Heat Sink ◽  
Heat Dissipation ◽  
Machining Process ◽  
High Power Led ◽  
Radial Heat

A phase change heat sink has higher heat transfer efficiency compared to a traditional metal solid heat sink, and is thus more preferred for the heat dissipation of high-power light-emitting diodes (LEDs) with very high heat flux. The boiling structure at the evaporation surface is the biggest factor that affects heat sink resistance. It is necessary to investigate the plastic deformation law during the machining process of boiling structures. In this study, a novel phase change radial heat sink was developed for high-power LED heat dissipation. First, a working principle and a fabrication process for the heat sink were introduced. Subsequently, to achieve an excellent heat dissipation performance, the machining process of boiling structures was numerically simulated and investigated. To be specific, plastic deformation generated during the formation was analyzed, and key parameters related to the morphology of the boiling structures were discussed including feeding angles and machining depths. Moreover, the finite element (FE) simulation results were compared with those of experiments. Last but not least, the heat transfer performance of the fabricated heat sink was tested. Results showed that the developed heat sink was well suited for a high-power LED application.

The Application of Heat Pipe Heat Sink for High Power LED Lamps

2014 ◽  
Vol 602-605 ◽  
pp. 2713-2716 ◽  
Author(s):  
Xin Rui Ding ◽  
Yu Ji Li ◽  
Zong Tao Li ◽  
Yong Tang ◽  
Bin Hai Yu ◽  
...  
Keyword(s):  
Heat Pipe ◽  
Thermal Performance ◽  
High Power ◽  
Heat Sink ◽  
Heat Dissipation ◽  
Heat Sinks ◽  
Practical Significance ◽  
Heat Accumulation ◽  
Element Analysis ◽  
High Power Led

LED has been regarded as the next generation lighting source. As for high power LED lamps, heat accumulation will cause a series of problems. Therefore, thermal management is very important for designing a high power LED lamp. Three types of heat sinks are designed by using the finite element analysis (FEA) method for an 180W high power LED lamp. Then the optimized heat sinks are developed and experiments are performed to demonstrate the simulated results. At the same time, the thermal performances with different working angles are investigated experimentally. The heat sink with heat pipe has a better heat dissipation performance than the conventional heat sink under the same input power. The working angles of the lamps greatly influence the thermal performance of each heat sink. For the same heat sink, the temperature varies with different install directions and working angles. Finally, the heat sink with the best thermal performance is recommended. The results have practical significance in designing high power LED lamps.

High Power LED Heat Dissipation Comparison Analysis via Aluminum and Copper Slug

2014 ◽  
Vol 893 ◽  
pp. 811-814
Author(s):  
Rajendaran Vairavan ◽  
Zaliman Sauli ◽  
Vithyacharan Retnasamy
Keyword(s):  
High Power ◽  
Heat Dissipation ◽  
Simulation Analysis ◽  
Input Power ◽  
Junction Temperature ◽  
Von Mises Stress ◽  
Comparison Analysis ◽  
Single Chip ◽  
High Power Led ◽  
Von Mises

The vast development of the LED industry has created contemporary set of thermal issues with limits the reliability of the high power LEDs. Thus, this paper reports a simulation analysis done on single chip high power LED package to evalute the effects of heat slug material on the heat dissipation of the LED package. The heat dissipation of two types of heat slug material, aluminum (Al) and copper (Cu) were compared in terms of junction temperature, von Mises stress and thermal resistance of the LED chip at varied input power of 0.1 W and 1W. Results of the analysis showed that the copper heat slug exhibits a better heat dissipation due to its superior thermal conductivity.

Copper Based Heat Slug Structure Variation Analysis on Heat Dissipation of High Power LED

2014 ◽  
Vol 1082 ◽  
pp. 340-343
Author(s):  
Vithyacharan Retnasamy ◽  
Zaliman Sauli ◽  
Rajendaran Vairavan ◽  
Hussin Kamarudin ◽  
Mukhzeer Mohamad Shahimin ◽  
...  
Keyword(s):  
Surface Area ◽  
Light Source ◽  
High Power ◽  
Heat Dissipation ◽  
Simulation Analysis ◽  
Variation Analysis ◽  
Single Chip ◽  
Structure Variation ◽  
Excess Heat ◽  
High Power Led

Excess heat generated by the high power LED package significantly impacts the performance and reliability of the light source. Significance of heat dissipation are influenced by each packaging component of high power LED. This paper demonstrates simulation analysis on single chip high power LED where the significance of the copper based heat slug structure on the heat dissipation was analyzed. The simulation analysis was carried out by using Ansys version 11 and heat dissipation of two types of heat slug structure, rectangular and cylindrical were compared. The outcome exhibited that the structure of the heat slug significantly influences the heat dissipation of LED chip due to its surface area.

Heat Sink Cooling Fan and Rotation Speed Effect Analysis on Heat Dissipation of High Power GaN LED Package

2014 ◽  
Vol 1082 ◽  
pp. 315-318
Author(s):  
Rajendaran Vairavan ◽  
Vithyacharan Retnasamy ◽  
Zaliman Sauli ◽  
Hussin Kamarudin ◽  
Muammar Mohamad Isa ◽  
...  
Keyword(s):  
Thermal Resistance ◽  
High Power ◽  
Heat Sink ◽  
Heat Dissipation ◽  
Rotation Speed ◽  
Junction Temperature ◽  
Von Mises Stress ◽  
Cooling Fan ◽  
High Power Led ◽  
Von Mises

In this work, thermal simulation analysis on high power LED is reported where the effect of the heat sink cooling fan and its rotation speed on the heat dissipation of the high power LED was evaluated. Ansys version 11 was utilized for the simulation. The thermal performance of the high power LED package was assessed in terms of operating junction temperature, von Mises stress and thermal resistance. The heat dissipation analysis was done under four types of convection condition:one natural convection conditionthree forced convection condition,. The forced convection condition was used to replicate the effect of a fan with various rotation speeds placed under the heat sink to increase the convective heat transfer coefficient. Results of the analysis showed that that the junction temperature, von Mises stress and thermal resistance of the GaN chip reduces with the increase of the fan rotation speed.

scholarly journals Analysis on High-Power Seaport LED Luminaire with Uniform Light Distribution Based on Optimized Lens and Heatsink

2021 ◽  
Vol 11 (9) ◽  
pp. 4035
Author(s):  
Jinsheon Kim ◽  
Jeungmo Kang ◽  
Woojin Jang
Keyword(s):  
Light Source ◽  
High Power ◽  
Heat Dissipation ◽  
Light Emitting Diode ◽  
Light Distribution ◽  
Light Sources ◽  
Led Light ◽  
High Power Led ◽  
Distribution Requirement ◽  
Lighting Application

In the case of light-emitting diode (LED) seaport luminaires, they should be designed in consideration of glare, average illuminance, and overall uniformity. Although it is possible to implement light distribution through auxiliary devices such as reflectors, it means increasing the weight and size of the luminaire, which reduces the feasibility. Considering the special environment of seaport luminaires, which are installed at a height of 30 m or more, it is necessary to reduce the weight of the device, facilitate replacement, and secure a light source with a long life. In this paper, an optimized lens design was investigated to provide uniform light distribution to meet the requirement in the seaport lighting application. Four types of lens were designed and fabricated to verify the uniform light distribution requirement for the seaport lighting application. Using numerical analysis, we optimized the lens that provides the required minimum overall uniformity for the seaport lighting application. A theoretical analysis for the heatsink structure and shape were conducted to reduce the heat from the high-power LED light sources up to 250 W. As a result of these analyses on the heat dissipation characteristics of the high-power LED light source used in the LED seaport luminaire, the heatsink with hexagonal-shape fins shows the best heat dissipation effect. Finally, a prototype LED seaport luminaire with an optimized lens and heat sink was fabricated and tested in a real seaport environment. The light distribution characteristics of this prototype LED seaport luminaire were compared with a commercial high-pressure sodium luminaire and metal halide luminaire.

Sign in / Sign up

Export Citation Format

Share Document