Copper Based Heat Slug Structure Variation Analysis on Heat Dissipation of High Power LED

2014 ◽  
Vol 1082 ◽  
pp. 340-343
Author(s):  
Vithyacharan Retnasamy ◽  
Zaliman Sauli ◽  
Rajendaran Vairavan ◽  
Hussin Kamarudin ◽  
Mukhzeer Mohamad Shahimin ◽  
...  
Keyword(s):  
Surface Area ◽  
Light Source ◽  
High Power ◽  
Heat Dissipation ◽  
Simulation Analysis ◽  
Variation Analysis ◽  
Single Chip ◽  
Structure Variation ◽  
Excess Heat ◽  
High Power Led

Excess heat generated by the high power LED package significantly impacts the performance and reliability of the light source. Significance of heat dissipation are influenced by each packaging component of high power LED. This paper demonstrates simulation analysis on single chip high power LED where the significance of the copper based heat slug structure on the heat dissipation was analyzed. The simulation analysis was carried out by using Ansys version 11 and heat dissipation of two types of heat slug structure, rectangular and cylindrical were compared. The outcome exhibited that the structure of the heat slug significantly influences the heat dissipation of LED chip due to its surface area.

High Power LED Heat Dissipation Comparison Analysis via Aluminum and Copper Slug

2014 ◽  
Vol 893 ◽  
pp. 811-814
Author(s):  
Rajendaran Vairavan ◽  
Zaliman Sauli ◽  
Vithyacharan Retnasamy
Keyword(s):  
High Power ◽  
Heat Dissipation ◽  
Simulation Analysis ◽  
Input Power ◽  
Junction Temperature ◽  
Von Mises Stress ◽  
Comparison Analysis ◽  
Single Chip ◽  
High Power Led ◽  
Von Mises

The vast development of the LED industry has created contemporary set of thermal issues with limits the reliability of the high power LEDs. Thus, this paper reports a simulation analysis done on single chip high power LED package to evalute the effects of heat slug material on the heat dissipation of the LED package. The heat dissipation of two types of heat slug material, aluminum (Al) and copper (Cu) were compared in terms of junction temperature, von Mises stress and thermal resistance of the LED chip at varied input power of 0.1 W and 1W. Results of the analysis showed that the copper heat slug exhibits a better heat dissipation due to its superior thermal conductivity.

scholarly journals Analysis on High-Power Seaport LED Luminaire with Uniform Light Distribution Based on Optimized Lens and Heatsink

2021 ◽  
Vol 11 (9) ◽  
pp. 4035
Author(s):  
Jinsheon Kim ◽  
Jeungmo Kang ◽  
Woojin Jang
Keyword(s):  
Light Source ◽  
High Power ◽  
Heat Dissipation ◽  
Light Emitting Diode ◽  
Light Distribution ◽  
Light Sources ◽  
Led Light ◽  
High Power Led ◽  
Distribution Requirement ◽  
Lighting Application

In the case of light-emitting diode (LED) seaport luminaires, they should be designed in consideration of glare, average illuminance, and overall uniformity. Although it is possible to implement light distribution through auxiliary devices such as reflectors, it means increasing the weight and size of the luminaire, which reduces the feasibility. Considering the special environment of seaport luminaires, which are installed at a height of 30 m or more, it is necessary to reduce the weight of the device, facilitate replacement, and secure a light source with a long life. In this paper, an optimized lens design was investigated to provide uniform light distribution to meet the requirement in the seaport lighting application. Four types of lens were designed and fabricated to verify the uniform light distribution requirement for the seaport lighting application. Using numerical analysis, we optimized the lens that provides the required minimum overall uniformity for the seaport lighting application. A theoretical analysis for the heatsink structure and shape were conducted to reduce the heat from the high-power LED light sources up to 250 W. As a result of these analyses on the heat dissipation characteristics of the high-power LED light source used in the LED seaport luminaire, the heatsink with hexagonal-shape fins shows the best heat dissipation effect. Finally, a prototype LED seaport luminaire with an optimized lens and heat sink was fabricated and tested in a real seaport environment. The light distribution characteristics of this prototype LED seaport luminaire were compared with a commercial high-pressure sodium luminaire and metal halide luminaire.

Heat Dissipation Simulation Analysis of High Power LED via Heat Slug Geometry Variation

2014 ◽  
Vol 1082 ◽  
pp. 344-347
Author(s):  
Vithyacharan Retnasamy ◽  
Zaliman Sauli ◽  
Rajendaran Vairavan ◽  
Hussin Kamarudin ◽  
Mukhzeer Mohamad Shahimin ◽  
...  
Keyword(s):  
High Power ◽  
Heat Dissipation ◽  
Simulation Analysis ◽  
Life Time ◽  
Junction Temperature ◽  
Von Mises Stress ◽  
Potential Development ◽  
High Power Led ◽  
Superior Surface ◽  
Von Mises

High power LEDs are currently being plagued by heat dissipation challenges due to its high power density thus limiting its further potential development and fulfillment. Exercising proper selection of packaging component could improve the life time of high power LED. In this work, the significance of the heat slug geometry on the heat dissipation of high power LED was addressed through simulation analysis. The heat slug geometries were varied in order to compare the heat dissipation of the high power LED. Ansys version 11 was utilized for the simulation. The heat dissipation of the high power LED was evaluated in terms of junction temperature, von Mises stress and thermal resistance. The key results of the analysis showed that a superior surface area is preferred for an enhanced heat dissipation of high power LED

Thermal Simulation Analysis of High Power LED with Varied Heat Sink Fin Design

2014 ◽  
Vol 1082 ◽  
pp. 332-335
Author(s):  
Vithyacharan Retnasamy ◽  
Zaliman Sauli ◽  
Hussin Kamarudin ◽  
Muammar Mohamad Isa ◽  
Gan Meng Kuan
Keyword(s):  
High Power ◽  
Heat Sink ◽  
Simulation Analysis ◽  
Input Power ◽  
Junction Temperature ◽  
Single Chip ◽  
Pin Fin ◽  
High Power Led ◽  
Different Shapes ◽  
Fin Design

In this paper, the heat distribution for single chip high power LED package attached with varied heat sink fin shapes were analyzed through simulation. The main focus of this study was to scrutinize the fluctuation of junction temperature with different shapes of heat sink fin designs. The simulation was done using Ansys version 11. The single chip LED was loaded with input power of 0.5 W and 1 W . Simulation was done at ambient temperature of 25°C under three convection coefficient of 5, 10 and 15 W/m2.oC respectively. The obtained results showed that the LED package with pyramid pin fin heat sink has demonstrated a better thermal performance compared to the LED package with cylindrical pin fin heat sink.

CuDia Slug Size Variation Analysis on Heat Dissipation of High Power LED

2014 ◽  
Vol 487 ◽  
pp. 33-36 ◽  
Author(s):  
Rajendaran Vairavan ◽  
Vithyacharan Retnasamy ◽  
Zaliman Sauli
Keyword(s):  
Natural Convection ◽  
High Power ◽  
Heat Dissipation ◽  
Size Variation ◽  
Simulation Method ◽  
Point Of View ◽  
Junction Temperature ◽  
Variation Analysis ◽  
Single Chip ◽  
Simulation Results

The current advancement of LED has prompt thermal challenges from the packaging point of view. The reliability of the LED is significantly influenced by each of its packaging component. This paper presents the investigation of heat slug size effect on the junction temperature and stress of single chip LED through simulation method. Ansys version 11 was utilized and the analysis was done with copper diamond rectangular heat slug under natural convection condition at ambient temperature of 25 °C.The simulation results indicated that junction temperature and the stress of the single chip LED is influenced by the size of heat slug.

Heat Slug Material Variation Analysis on Thermal Dissipation of High Power LED

2014 ◽  
Vol 1082 ◽  
pp. 319-322
Author(s):  
Vithyacharan Retnasamy ◽  
Zaliman Sauli ◽  
Rajendaran Vairavan ◽  
Steven Taniselass ◽  
Hussin Kamarudin
Keyword(s):  
High Power ◽  
Heat Dissipation ◽  
Simulation Method ◽  
Packaging Material ◽  
Thermal Dissipation ◽  
Junction Temperature ◽  
Von Mises Stress ◽  
Variation Analysis ◽  
High Power Led ◽  
Von Mises

Accession of power in high power LED light source has resulted in thermal issue which causes reliability malfunction due to deficient heat dissipation. However, the heat disspation of high power LED can be enhance by improving packaging material selection.Thus, in this work, the connotation of heat slug material on the thermal performance of high power LED package was analyzed through simulation method. The significance of two heat slug materials, copper (Cu) and copper diamond (CuDia) were evaluated in terms of junction temperature, von Mises stress and thermal resistance. The simulation was executed using Ansys version 11 at ambient temperature of 25 °C with natural convection condition.

The Design Research of Single-Chip High Power LED Radiator

2011 ◽  
Vol 103 ◽  
pp. 219-224
Author(s):  
Yuan Luo ◽  
Ti Wei Wei ◽  
Zheng Wei Tang ◽  
Wei Xi Kong
Keyword(s):  
High Power ◽  
Thermal Effects ◽  
Heat Dissipation ◽  
Design Research ◽  
Junction Temperature ◽  
White Led ◽  
Single Chip ◽  
Finite Element Software ◽  
High Power Led ◽  
New Generation

As new generation of solid-state lighting source with green environmental protection, White LED has become the focus of attentions. Along with the development of high power LED, heat dissipation problems of LED become more and more important. This paper makes research on single-chip high power LED by ANSYS finite element software, and analyzes the thermal effects of parameters on the radiator. This paper believes that the influence of radiator materials’ thermal conductivity is not obvious, and the finned height and cooling area of radiator play an very important role in reducing chip junction temperature.

Analysis and Optimization of Heat Dissipation Characteristics of High-power LED

2021 ◽  
Author(s):  
Pingfeng Wu ◽  
Runji Fang ◽  
Xuanjun Dai ◽  
Anak Agung Ayu Putri
Keyword(s):  
High Power ◽  
Heat Dissipation ◽  
High Power Led
Sign in / Sign up

Export Citation Format

Share Document