Impact of β‐glucan on debittering, bioaccessibility and storage stability of skim milk fortified with shrimp oil nanoliposomes

2019 ◽  
Vol 55 (5) ◽  
pp. 2092-2103 ◽  
Author(s):  
Saqib Gulzar ◽  
Soottawat Benjakul ◽  
Wael N. Hozzein
2018 ◽  
Vol 3 (4) ◽  
pp. 41-49
Author(s):  
Adnan Khaliq ◽  
◽  
Moazzam Rafiq Khan ◽  
Samreen Ahsan ◽  
Muhammad Farhan Jahangir Chughtai ◽  
...  

2020 ◽  
Vol 278 ◽  
pp. 109922 ◽  
Author(s):  
Morten Vormsborg Christiansen ◽  
Troels Bjerregaard Pedersen ◽  
Jesper Nagstrup Brønd ◽  
Leif H. Skibsted ◽  
Lilia Ahrné

Molecules ◽  
2021 ◽  
Vol 26 (8) ◽  
pp. 2339
Author(s):  
So-Yul Yun ◽  
Jee-Young Imm

Age gelation is a major quality defect in ultra-high-temperature (UHT) pasteurized milk during extended storage. Changes in plasmin (PL)-induced sedimentation were investigated during storage (23 °C and 37 °C, four weeks) of UHT skim milk treated with PL (2.5, 10, and 15 U/L). The increase in particle size and broadening of the particle size distribution of samples during storage were dependent on the PL concentration, storage period, and storage temperature. Sediment analysis indicated that elevated storage temperature accelerated protein sedimentation. The initial PL concentration was positively correlated with the amount of protein sediment in samples stored at 23 °C for four weeks (r = 0.615; p < 0.01), whereas this correlation was negative in samples stored at 37 °C for the same time (r = −0.358; p < 0.01) due to extensive proteolysis. SDS-PAGE revealed that whey proteins remained soluble over storage at 23 °C for four weeks, but they mostly disappeared from the soluble phase of PL-added samples after two weeks’ storage at 37 °C. Transmission electron micrographs of PL-containing UHT skim milk during storage at different temperatures supported the trend of sediment analysis well. Based on the Fourier transform infrared spectra of UHT skim milk stored at 23 °C for three weeks, PL-induced particle size enlargement was due to protein aggregation and the formation of intermolecular β-sheet structures, which contributed to casein destabilization, leading to sediment formation.


Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1397
Author(s):  
Nappaphan Kunanusont ◽  
Boonchai Sangpetngam ◽  
Anongnat Somwangthanaroj

Plastic waste has been incorporated with asphalt to improve the physical properties of asphalt and alleviate the increasing trend of plastic waste being introduced into the environment. However, plastic waste comes in different types such as thermoplastic or thermoset, which results in varied properties of polymer modified asphalt (PMA). In this work, four thermoplastic vulcanizates (TPVs) were prepared using different peroxide concentrations to produce four formulations of gel content (with varying extent of crosslinked part) in order to imitate the variation of plastic waste. All four TPVs were then mixed with asphalt at 5 wt% thus producing four formulations of PMA, which went through physical, rheological, and storage stability assessments. PMA with higher gel content possessed lower penetration and higher softening temperature, indicating physically harder appearance of PMA. Superpave parameters remained unchanged among different gel content PMA at temperatures of 64, 70, and 76 °C. PMA with any level of gel content had lower Brookfield viscosity than PMA without gel content at a temperature of 135 °C. Higher gel content resulted in shorter storage stability measured with greater different softening temperatures between top and bottom layers of PMA after 5 days of 163 °C storage. This study shows that asphalt with thermoset plastic waste is harder and easier to pave, thus making the non-recycling thermoset plastic waste more useful and friendly to the environment.


Sign in / Sign up

Export Citation Format

Share Document