Periodic Unsteadiness of Tip Clearance Vortex in an Axial Compressor Rotor

2021 ◽  
Author(s):  
Fan Yang ◽  
Yanhui Wu ◽  
Ziyun Zhang ◽  
Zhenyang Wang
Keyword(s):  
Axial Compressor ◽  
Tip Clearance ◽  
Compressor Rotor ◽  
Tip Clearance Vortex

3-D Digital PIV Measurements of the Tip Clearance Flow in an Axial Compressor

2002 ◽  
Author(s):  
Mark P. Wernet ◽  
Dale Van Zante ◽  
Tony J. Strazisar ◽  
W. Trevor John ◽  
P. Susan Prahst
Keyword(s):  
Three Dimensional ◽  
Axial Compressor ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Image Velocimetry ◽  
Clearance Flow ◽  
Compressor Performance ◽  
Tip Clearance Vortex

The accurate characterization and simulation of rotor tip clearance flows has received much attention in recent years due to their impact on compressor-performance and stability. At NASA Glenn the first known three dimensional Digital Particle Image Velocimetry (DPIV) measurements of the tip region of a low speed compressor rotor have been acquired to characterize the behavior of the rotor tip clearance flow. The measurements were acquired phase-locked to the rotor position so that changes in the tip clearance vortex position relative to the rotor blade can be seen. The DPIV technique allows the magnitude and relative contributions of both the asynchronous motions of a coherent structure and the temporal unsteadiness to be evaluated. Comparison of measurements taken at the peak efficiency and at near stall operating conditions characterizes the mean position of the clearance vortex and the changes in the unsteady behavior of the vortex with blade loading. Comparisons of the 3-D DPIV measurements at the compressor design point to a 3D steady N-S solution are also done to assess the fidelity of steady, single-passage simulations to model an unsteady flow field.

Periodic Unsteadiness of Tip Clearance Vortex in an Axial Compressor Rotor

2020 ◽  
Author(s):  
Fan Yang ◽  
Yanhui Wu ◽  
Ziyun Zhang ◽  
Zhenyang Wang
Keyword(s):  
Vortex Core ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Small Range ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Blade Tip ◽  
Periodic Fluctuations ◽  
Tip Clearance Vortex

Abstract A series of unsteady simulations, supported by experimental data, are used to characterize the periodic unsteadiness of the tip clearance vortex in an axial compressor rotor. The numerical probes detect significant periodic fluctuations in the blade tip region at near stall conditions. A reduced frequency at different condition is limited to a small range although there exist a large difference on the natural frequency. Physical explanations of the periodic fluctuations are made in terms of vortex-core identification, contour, etc. The nature of the periodic unsteadiness in the tip region is the periodic bubble-type breakdown of the tip leakage vortex induced by the broken vortex core generated by the previous breakdown. The life cycle of the broken vortex core can be summarized as three processes, generation, propagation and inducing breakdown of tip leakage vortex. The broken vortex core arrives at mid-chord of the adjacent blade, resulting in change of momentum in the tip clearance and pressure in the leading edge of the adjacent blade. The flow in this blade tip region is similarly affected by another adjacent blade. The tip leakage vortex core is bent, then the breakdown of tip clearance happens and a new broken vortex core appears accompanied by a back flow region.

Experimental Investigation Into the Effects of the Steady Wake-Tip Clearance Vortex Interaction in a Compressor Cascade

2015 ◽  
Vol 137 (6) ◽  
Author(s):  
Andreas Krug ◽  
Peter Busse ◽  
Konrad Vogeler
Keyword(s):  
Flow Field ◽  
Experimental Studies ◽  
Axial Compressor ◽  
Field Measurements ◽  
Tip Clearance ◽  
Compressor Cascade ◽  
Unsteady Interaction ◽  
Linear Compressor Cascade ◽  
Tip Clearance Vortex ◽  
The Impact

An important aspect of the aerodynamic flow field in the tip region of axial compressor rotors is the unsteady interaction between the tip clearance vortex (TCV) and the incoming stator wakes. In order to gain an improved understanding of the mechanics involved, systematic studies need to be performed. As a first step toward the characterization of the dynamic effects caused by the relative movement of the blade rows, the impact of a stationary wake-induced inlet disturbance on a linear compressor cascade with tip clearance will be analyzed. The wakes were generated by a fixed grid of cylindrical bars with variable pitch being placed at discrete pitchwise positions. This paper focuses on experimental studies conducted at the newly designed low-speed cascade wind tunnel in Dresden. The general tunnel configuration and details on the specific cascade setup will be presented. Steady state flow field measurements were carried out using five-hole probe traverses up- and downstream of the cascade and accompanied by static wall pressure readings. 2D-particle image velocimetry (PIV) measurements complemented these results by visualizing the blade-to-blade flow field. Hence, the structure of the evolving secondary flow system is evaluated and compared for all tested configurations.

Factors Affecting Measured Axial Compressor Tip Clearance Vortex Circulation

1995 ◽  
Vol 117 (3) ◽  
pp. 487-490 ◽  
Author(s):  
S. A. Khalid
Keyword(s):  
Viscous Flow ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Radial Transport ◽  
Factors Affecting ◽  
Blade Tip ◽  
Tip Clearance Vortex ◽  
The Relationship ◽  
Principal Contributor

The relationship between turbomachinery blade circulation and tip clearance vortex circulation measured experimentally is examined using three-dimensional viscous flow computations. It is shown that the clearance vortex circulation one would measure is dependent on the placement of the fluid contour around which the circulation measurement is taken. Radial transport of vorticity results in the magnitude of the measured clearance vortex circulation generally being less than the blade circulation. For compressors, radial transport of vorticity shed from the blade tip in proximity to the endwall is the principal contributor to the discrepancy between the measured vortex circulation and blade circulation. Further, diffusion of vorticity shed at the blade tip toward the endwall makes it impossible in most practical cases to construct a fluid contour around the vortex that encloses all, and only, the vorticity shed from the blade tip. One should thus not expect agreement between measured tip clearance vortex circulation and circulation around the blade.

Behavior of Tip Leakage Flow Behind an Axial Compressor Rotor

1986 ◽  
Vol 108 (1) ◽  
pp. 7-14 ◽  
Author(s):  
M. Inoue ◽  
M. Kuroumaru ◽  
M. Fukuhara
Keyword(s):  
Incidence Angle ◽  
Axial Compressor ◽  
Performance Testing ◽  
Tip Clearance ◽  
Vortex Center ◽  
Tip Leakage Flow ◽  
Flow Measurements ◽  
Wall Boundary Layer ◽  
Compressor Rotor ◽  
Work Done

Performance testing and detailed flow measurements were made in an axial compressor rotor with various tip clearances. The experiments were conducted on the condition of the same incidence angle at midspan. Thus, the effect of tip clearance distinguished from that of incidence angle was investigated on the overall performance, work-done factor, blockage factor, and increases in displacement, momentum, and blade-force-deficit thicknesses of the casing wall boundary layer, The phase-locked flow patterns obtained by the multisampling technique show clear evidence of a leakage vortex core behind the rotor. Behavior of the leakage vortex was clarified for various tip clearances by examining loci of the vortex center, decay characteristics of the vorticity at the center, and the total amount of vorticity shed from the blade tip. These results were compared with the leakage vortex model presented by Lakshminarayana.

Effect of tip clearance size on the performance of a low-reaction transonic axial compressor rotor

2019 ◽  
Vol 234 (2) ◽  
pp. 127-142
Author(s):  
Wei Zhu ◽  
Songtao Wang ◽  
Longxin Zhang ◽  
Jun Ding ◽  
Zhongqi Wang
Keyword(s):  
Numerical Simulations ◽  
Dynamic Balance ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Flow Phenomena

This study aimed to enhance the understanding of flow phenomena in low-reaction aspirated compressors. Three-dimensional, multi-passage steady and unsteady numerical simulations are performed to investigate the performance sensitivity to tip clearance variation on the first-stage rotor of a multistage low-reaction aspirated compressor. Three kinds of tip clearance sizes including 1.0τ, 2.0τ and 3.0τ are modeled, in which 1.0τ corresponds to the designed tip clearance size of 0.2 mm. The steady numerical simulations show that the overall performance of the rotor moves toward lower mass flow rate when the tip clearance size is increased. Moreover, energy losses, efficiency reduction and stall margin decrease are also observed with increasing tip clearance size. This can be mostly attributed to the damaging impact of intense tip clearance flow. For unsteady simulation, the result shows periodical oscillation of the tip leakage vortex and a “two-passage periodic structure” in the tip region at the near-stall point. The occurrence of the periodical oscillation is due to the severe interaction between the tip clearance flow and the shock wave. However, the rotor operating state is still stable at this working point because a dynamic balance is established between the tip clearance flow and incoming flow.

Investigation of Unsteady Flow Field in a Low-Speed One and a Half Stage Axial Compressor: Effects of Tip Gap Size on the Tip Clearance Flow Structure at Near Stall Operation

2014 ◽  
Author(s):  
Chunill Hah ◽  
Michael Hathaway ◽  
Joseph Katz
Keyword(s):  
Unsteady Flow ◽  
Flow Structure ◽  
Flow Instability ◽  
Axial Compressor ◽  
Leading Edge ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Low Speed ◽  
Clearance Flow ◽  
Tip Clearance Vortex

The primary focus of this paper is to investigate the effect of rotor tip gap size on how the rotor unsteady tip clearance flow structure changes in a low speed one and half stage axial compressor at near stall operation (for example, where maximum pressure rise is obtained). A Large Eddy Simulation (LES) is applied to calculate the unsteady flow field at this flow condition with both a small and a large tip gaps. The numerically obtained flow fields at the small clearance matches fairly well with the available initial measurements obtained at the Johns Hopkins University with 3-D unsteady PIV in an index-matched test facility which renders the compressor blades and casing optically transparent. With this setup, the unsteady velocity field in the entire flow domain, including the flow inside the tip gap, can be measured. The numerical results are also compared with previously published measurements in a low speed single stage compressor (Maerz et al. [2002]). The current study shows that, with the smaller rotor tip gap, the tip clearance vortex moves to the leading edge plane at near stall operating condition, creating a nearly circumferentially aligned vortex that persists around the entire rotor. On the other hand, with a large tip gap, the clearance vortex stays inside the blade passage at near stall operation. With the large tip gap, flow instability and related large pressure fluctuation at the leading edge are observed in this one and a half stage compressor. Detailed examination of the unsteady flow structure in this compressor stage reveals that the flow instability is due to shed vortices near the leading edge, and not due to a three-dimensional separation vortex originating from the suction side of the blade, which is commonly referred to during a spike-type stall inception. The entire tip clearance flow is highly unsteady. Many vortex structures in the tip clearance flow, including the sheet vortex system near the casing, interact with each other. The core tip clearance vortex, which is formed with the rotor tip gap flows near the leading edge, is also highly unsteady or intermittent due to pressure oscillations near the leading edge and varies from passage to passage. For the current compressor stage, the evidence does not seem to support that a classical vortex breakup occurs in any organized way, even with the large tip gap. Although wakes from the IGV influence the tip clearance flow in the rotor, the major characteristics of rotor tip clearance flows in isolated or single stage rotors are observed in this one and a half stage axial compressor.

scholarly journals Blockage Development in a Transonic, Axial Compressor Rotor

1997 ◽  
Author(s):  
Kenneth L. Suder
Keyword(s):  
Boundary Layer ◽  
Axial Compressor ◽  
Flow Region ◽  
Tip Clearance ◽  
Surface Boundary ◽  
Core Flow ◽  
The Core ◽  
Compressor Rotor ◽  
Transonic Axial Compressor ◽  
The Impact

A detailed experimental investigation to understand and quantify the development of blockage in the flow field of a transonic, axial flow compressor rotor (NASA Rotor 37) has been undertaken. Detailed laser anemometer measurements were acquired upstream, within, and downstream of a transonic, axial compressor rotor operating at 100%, 85%, 80%, and 60% of design speed which provided inlet relative Mach numbers at the blade tip of 1.48, 1.26, 1.18, and 0.89 respectively. The impact of the shock on the blockage development, pertaining to both the shock / boundary layer interactions and the shock / tip clearance flow interactions, is discussed. The results indicate that for this rotor the blockage in the endwall region is 2–3 times that of the core flow region, and the blockage in the core flow region more than doubles when the shock strength is sufficient to separate the suction surface boundary layer.

Numerical Investigation of Relation Between Unsteady Behavior of Tip Leakage Vortex and Rotating Disturbance in a Transonic Axial Compressor Rotor

2008 ◽  
Author(s):  
K. Yamada ◽  
K. Funazaki ◽  
H. Sasaki
Keyword(s):  
Vortex Breakdown ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Tip Leakage Vortex ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Transonic Axial Compressor ◽  
Rotating Instability

The purpose of this study is to have a better understanding of the unsteady behavior of tip clearance flow at near-stall condition from a multi-passage simulation and to clarify the relation between such unsteadiness and rotating disturbance. This study is motivated by the following concern. A single passage simulation has revealed the occurrence of the tip leakage vortex breakdown at near-stall condition in a transonic axial compressor rotor, leading to the unsteadiness of the tip clearance flow field in the rotor passage. These unsteady flow phenomena were similar to those in the rotating instability, which is classified in one of the rotating disturbances. In other words it is possible that the tip leakage vortex breakdown produces a rotating disturbance such as the rotating instability. Three-dimensional unsteady RANS calculation was conducted to simulate the rotating disturbance in a transonic axial compressor rotor (NASA Rotor 37). The four-passage simulation was performed so as to capture a short length scale disturbance like the rotating instability and the spike-type stall inception. The simulation demonstrated that the unsteadiness of tip leakage vortex, which was derived from the vortex breakdown at near-stall condition, invoked the rotating disturbance in the rotor, which is similar to the rotating instability.

Sign in / Sign up

Export Citation Format

Share Document