Kinematics and Optimization of a Spatial 3-UPU Parallel Manipulator

1999 ◽  
Vol 122 (4) ◽  
pp. 439-446 ◽  
Author(s):  
Lung-Wen Tsai ◽  
Sameer Joshi
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Structural Characteristics ◽  
Translational Motion ◽  
Parallel Manipulators ◽  
Condition Index ◽  
Mirror Image ◽  
Geometric Conditions ◽  
Design Variables ◽  
Opposite Limb

The structural characteristics associated with parallel manipulators are investigated. Using these characteristics a class of 3 degree-of-freedom parallel manipulators are enumerated. Several parallel manipulators with only translational degrees of freedom are identified and the 3-UPU parallel manipulator is chosen for design analysis and optimization. The kinematics of this 3-UPU parallel manipulator is studied. Two geometric conditions that lead to pure translational motion of the moving platform are described. Due to the simple kinematic structure, the inverse kinematics yields two equal and opposite limb lengths whereas the direct kinematics produces two possible manipulator postures with one being the mirror image of the other. The Jacobian matrix is derived and several singular conditions are discussed. Furthermore the conditions for existence of an isotropic point within the workspace are discussed and equations to compute the isotropic configurations of a 3-UPU manipulator are derived. Finally, we undertake architecture optimization and show that certain values of design variables maximize the global condition index of the 3-UPU manipulator. [S1050-0472(00)01404-5]

A novel class of generalized parallel manipulators with high rotational capability

2020 ◽  
Vol 234 (23) ◽  
pp. 4599-4619
Author(s):  
Chunxu Tian ◽  
Dan Zhang ◽  
Jian Liu
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Structural Characteristics ◽  
Synthesis Method ◽  
Parallel Manipulators ◽  
Rigid Bodies ◽  
Kinematic Chains ◽  
Moving Platforms ◽  
Moving Platform ◽  
Limb Structure

A conventional parallel manipulator is characterized by connecting one moving platform with two or more serial kinematic limbs. Since each limb is independently supporting one moving platform, the moving platform must be a rigid body with several kinematic pairs fixed on it. However, for generalized parallel manipulators with articulated moving platforms, the moving platforms are not limited to rigid bodies but including serial kinematic chains or internal kinematic joints. The introduction of articulated moving platforms allows for improving the kinematic performance of generalized parallel manipulators, especially for rotational capability. On account of the structural characteristics of the moving platforms, it also poses a significant challenge in the construction of the structures of manipulators. This research raises a new method for the type synthesis of generalized parallel manipulators with novel articulated moving platforms. The proposed method introduces a striking shortcut for the limb structure analysis of mechanisms with high rotational capability. In this paper, a class of generalized parallel manipulator with different degrees of freedom from 3 to 6 are constructed by using the constraint synthesis method, and several examples are provided to demonstrate the feasibility of the advocated method. At last, the 3T3R generalized parallel manipulator is taken as an example to analyze the inverse kinematics, and the evaluation of the workspace is conducted to verify the rotational capacity.

Determination of the Workspace of a Three-Degrees-of-Freedom Parallel Manipulator Using a Three-Dimensional Computer-Aided-Design Software Package and the Concept of Virtual Chains1

2015 ◽  
Vol 8 (2) ◽  
Author(s):  
Andrew Johnson ◽  
Xianwen Kong ◽  
James Ritchie
Keyword(s):  
Computer Aided Design ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Graphical Representation ◽  
Three Dimensional ◽  
Parallel Manipulators ◽  
Workspace Analysis ◽  
Computer Aided ◽  
Aided Design

The determination of workspace is an essential step in the development of parallel manipulators. By extending the virtual-chain (VC) approach to the type synthesis of parallel manipulators, this technical brief proposes a VC approach to the workspace analysis of parallel manipulators. This method is first outlined before being illustrated by the production of a three-dimensional (3D) computer-aided-design (CAD) model of a 3-RPS parallel manipulator and evaluating it for the workspace of the manipulator. Here, R, P and S denote revolute, prismatic and spherical joints respectively. The VC represents the motion capability of moving platform of a manipulator and is shown to be very useful in the production of a graphical representation of the workspace. Using this approach, the link interferences and certain transmission indices can be easily taken into consideration in determining the workspace of a parallel manipulator.

Dynamic Modeling of a Parallel Manipulator With Three Translational Degrees of Freedom

1998 ◽  
Author(s):  
Richard Stamper ◽  
Lung-Wen Tsai
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Close Agreement ◽  
Jacobian Matrix ◽  
Parallel Manipulators ◽  
Kinematic Structure ◽  
End Effector ◽  
Moving Platform ◽  
Euler Approach ◽  
Computationally Intensive

Abstract The dynamics of a parallel manipulator with three translational degrees of freedom are considered. Two models are developed to characterize the dynamics of the manipulator. The first is a traditional Lagrangian based model, and is presented to provide a basis of comparison for the second approach. The second model is based on a simplified Newton-Euler formulation. This method takes advantage of the kinematic structure of this type of parallel manipulator that allows the actuators to be mounted directly on the base. Accordingly, the dynamics of the manipulator is dominated by the mass of the moving platform, end-effector, and payload rather than the mass of the actuators. This paper suggests a new method to approach the dynamics of parallel manipulators that takes advantage of this characteristic. Using this method the forces that define the motion of moving platform are mapped to the actuators using the Jacobian matrix, allowing a simplified Newton-Euler approach to be applied. This second method offers the advantage of characterizing the dynamics of the manipulator nearly as well as the Lagrangian approach while being less computationally intensive. A numerical example is presented to illustrate the close agreement between the two models.

A Family of 3-DOF Translational Parallel Manipulators1

2003 ◽  
Vol 125 (2) ◽  
pp. 302-307 ◽  
Author(s):  
Marco Carricato ◽  
Vincenzo Parenti-Castelli
Keyword(s):  
Degrees Of Freedom ◽  
Translational Motion ◽  
Parallel Manipulators ◽  
Geometric Interpretation ◽  
The Other ◽  
Six Degrees Of Freedom ◽  
Revolute Joints ◽  
Rotational Degrees Of Freedom

This article addresses parallel manipulators with fewer than six degrees of freedom, whose use may prove valuable in those applications in which a higher mobility is uncalled for. In particular, a family of 3-dof manipulators containing only revolute joints or at the most revolute and prismatic ones is studied. Design and assembly conditions sufficient to provide the travelling platform with a pure translational motion are determined and two sub-families that fulfill the imposed constraint are found: one is already known in the literature, while the other is original. The new architecture does not exhibit rotation singularities, i.e., configurations in which the platform gains rotational degrees of freedom. A geometric interpretation of the translation singularities is provided.

A Novel Parallel Mechanism With 3-RRUR Legs

2007 ◽  
Author(s):  
Yanwen Li ◽  
Yueyue Zhang ◽  
Lumin Wang ◽  
Zhen Huang
Keyword(s):  
Machine Tools ◽  
Parallel Mechanism ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Parallel Manipulators ◽  
Forward Kinematics ◽  
Symmetrical Structure ◽  
Forward Kinematic ◽  
Accumulated Error

This paper investigates a novel 4-DOF 3-RRUR parallel manipulator, the number and the characteristics of its degrees of freedom are determined firstly, the rational input plan and the invert and forward kinematic solutions are carried out then. The corresponding numeral example of the forward kinematics is given. This type of parallel manipulators has a symmetrical structure, less accumulated error, and can be used to construct virtual-axis machine tools. The analysis in this paper will play an important role in promoting the application of such manipulators.

A Measure for Evaluation of Maximum Acceleration of Redundant and Nonredundant Parallel Manipulators

2015 ◽  
Vol 8 (2) ◽  
Author(s):  
Jun Wu ◽  
Binbin Zhang ◽  
Liping Wang
Keyword(s):  
Dynamic Model ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Virtual Work ◽  
Parallel Manipulators ◽  
Maximum Acceleration ◽  
Virtual Work Principle ◽  
Joint Force ◽  
Joint Forces ◽  
Three Degrees Of Freedom

The paper deals with the evaluation of acceleration of redundant and nonredundant parallel manipulators. The dynamic model of three degrees-of-freedom (3DOF) parallel manipulator is derived by using the virtual work principle. Based on the dynamic model, a measure is proposed for the acceleration evaluation of the redundant parallel manipulator and its nonredundant counterpart. The measure is designed on the basis of the maximum acceleration of the mobile platform when one actuated joint force is unit and other actuated joint forces are less than or equal to a unit force. The measure for evaluation of acceleration can be used to evaluate the acceleration of both redundant parallel manipulators and nonredundant parallel manipulators. Furthermore, the acceleration of the 4-PSS-PU parallel manipulator and its nonredundant counterpart are compared.

Kinematic Synthesis of a Spatial 3-RPS Parallel Manipulator

2003 ◽  
Vol 125 (1) ◽  
pp. 92-97 ◽  
Author(s):  
Han Sung Kim ◽  
Lung-Wen Tsai
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Parallel Manipulators ◽  
Point Of View ◽  
Dimensional Synthesis ◽  
Kinematic Synthesis ◽  
End Effector ◽  
Solution Methods ◽  
Moving Platform ◽  
At Will

This paper presents the design of spatial 3-RPS parallel manipulators from dimensional synthesis point of view. Since a spatial 3-RPS manipulator has only 3 degrees of freedom, its end effector cannot be positioned arbitrarily in space. It is shown that at most six positions and orientations of the moving platform can be prescribed at will and, given six prescribed positions, there are at most ten RPS chains that can be used to construct up to 120 manipulators. Further, solution methods for fewer than six prescribed positions are also described.

A 2(3-RRPS) parallel manipulator inspired by Gough–Stewart platform

Robotica ◽  
2012 ◽  
Vol 31 (3) ◽  
pp. 381-388 ◽  
Author(s):  
Jaime Gallardo-Alvarado ◽  
Mario A. García-Murillo ◽  
Eduardo Castillo-Castaneda
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Screw Theory ◽  
Parallel Manipulators ◽  
Forward Kinematics ◽  
Triangular Prism ◽  
Input Output ◽  
Six Degrees Of Freedom ◽  
Moving Platform

SUMMARYThis study addresses the kinematics of a six-degrees-of-freedom parallel manipulator whose moving platform is a regular triangular prism. The moving and fixed platforms are connected to each other by means of two identical parallel manipulators. Simple forward kinematics and reduced singular regions are the main benefits offered by the proposed parallel manipulator. The Input–Output equations of velocity and acceleration are systematically obtained by resorting to reciprocal-screw theory. A case study, which is verified with the aid of commercially available software, is included with the purpose to exemplify the application of the method of kinematic analysis.

A new family of spherical parallel manipulators

Robotica ◽  
2002 ◽  
Vol 20 (4) ◽  
pp. 353-358 ◽  
Author(s):  
Raffaele Di Gregorio
Keyword(s):  
Parallel Manipulator ◽  
Parallel Manipulators ◽  
End Effector ◽  
Singular Configurations ◽  
New Family ◽  
Geometric Conditions ◽  
Singularity Locus ◽  
The Given ◽  
Spherical Parallel Manipulator ◽  
Spherical Motion

In the literature, 3-RRPRR architectures were proposed to obtain pure translation manipulators. Moreover, the geometric conditions, which 3-RRPRR architectures must match, in order to make the end-effector (platform) perform infinitesimal (elementary) spherical motion were enunciated. The ability to perform elementary spherical motion is a necessary but not sufficient condition to conclude that the platform is bound to accomplish finite spherical motion, i.e. that the mechanism is a spherical parallel manipulator (parallel wrist). This paper demonstrates that the 3-RRPRR architectures matching the geometric conditions for elementary spherical motion make the platform accomplish finite spherical motion, i.e. they are parallel wrists (3-RRPRR wrist), provided that some singular configurations, named translation singularities, are not reached. Moreover, it shows that 3-RRPRR wrists belong to a family of parallel wrists which share the same analytic expression of the constraints which the legs impose on the platform. Finally, the condition that identifies all the translation singularities of the mechanisms of this family is found and geometrically interpreted. The result of this analysis is that the translation singularity locus can be represented by a surface (singularity surface) in the configuration space of the mechanism. Singularity surfaces drawn by exploiting the given condition are useful tools in designing these wrists.

Workspace Analysis and Going through Singularities of 5-Bar Symmetric Planar Parallel Manipulator by Automated Selective Actuation Mechanism

2012 ◽  
Vol 588-589 ◽  
pp. 1664-1668
Author(s):  
Syam Sundar ◽  
Vijay S. Rathore ◽  
Manoj K. Sahi ◽  
V. Upendran ◽  
Anjan Kumar Dash
Keyword(s):  
Closed Form ◽  
Parallel Manipulator ◽  
Parallel Manipulators ◽  
New Approach ◽  
Serial Manipulators ◽  
Actuation Mechanism ◽  
Geometric Conditions ◽  
Workspace Analysis ◽  
Planar Parallel Manipulator ◽  
Planar Parallel Manipulators

In this article‚ a new approach is presented to determine the various shapes of workspaces of 5 bar symmetric planar parallel manipulators. Here the shape of the workspace is determined by the number of ways the workspaces of the two serial manipulators intersect with each other. Geometric conditions are established in each case and area of each shape of workspace is determined in closed form. Singularity is another important consideration in the design of parallel manipulators. In this paper, an approach is presented to go through the singularity points using an automatic selective actuation mechanism. A prototype 5-bar planar manipulator is fabricated along with an automatic selective actuation mechanism demonstrating the manipulator going through the singularity points.

Sign in / Sign up

Export Citation Format

Share Document