scholarly journals Experimental and Computational Investigation of the Tip Clearance Flow in a Transonic Axial Compressor Rotor

1996 ◽  
Vol 118 (2) ◽  
pp. 218-229 ◽  
Author(s):  
K. L. Suder ◽  
M. L. Celestina
Keyword(s):  
Axial Compressor ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Vortex Interaction ◽  
Peak Efficiency ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Transonic Axial Compressor ◽  
Design Speed

Experimental and computational techniques are used to investigate tip clearance flows in a transonic axial compressor rotor at design and part-speed conditions. Laser anemometer data acquired in the endwall region are presented for operating conditions near peak efficiency and near stall at 100 percent design speed and at near peak efficiency at 60 percent design speed. The role of the passage shock/leakage vortex interaction in generating endwall blockage is discussed. As a result of the shock/vortex interaction at design speed, the radial influence of the tip clearance flow extends to 20 times the physical tip clearance height. At part speed, in the absence of the shock, the radial extent is only five times the tip clearance height. Both measurements and analysis indicate that under part-speed operating conditions a second vortex, which does not originate from the tip leakage flow, forms in the end-wall region within the blade passage and exits the passage near midpitch. Mixing of the leakage vortex with the primary flow downstream of the rotor at both design and part-speed conditions is also discussed.

scholarly journals Experimental and Computational Investigation of the Tip Clearance Flow in a Transonic Axial Compressor Rotor

1994 ◽  
Author(s):  
Kenneth L. Suder ◽  
Mark L. Celestina
Keyword(s):  
Axial Compressor ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Vortex Interaction ◽  
Peak Efficiency ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Transonic Axial Compressor ◽  
Design Speed

Experimental and computational techniques are used to investigate tip clearance flows in a transonic axial compressor rotor at design and part speed conditions. Laser anemometer data acquired in the endwall region are presented for operating conditions near peak efficiency and near stall at 100% design speed and at near peak efficiency at 60% design speed. The role of the passage shock / leakage vortex interaction in generating endwall blockage is discussed. As a result of the shock / vortex interaction at design speed, the radial influence of the tip clearance flow extends to 20 times the physical tip clearance height. At part speed, in the absence of the shock, the radial extent is only 5 times the tip clearance height. Both measurements and analysis indicate that under part-speed operating conditions a second vortex, which does not originate from the tip leakage flow, forms in the endwall region within the blade passage and exits the passage near midpitch. Mixing of the leakage vortex with the primary flow downstream of the rotor at both design and part speed conditions is also discussed.

Numerical Investigation of Relation Between Unsteady Behavior of Tip Leakage Vortex and Rotating Disturbance in a Transonic Axial Compressor Rotor

2008 ◽  
Author(s):  
K. Yamada ◽  
K. Funazaki ◽  
H. Sasaki
Keyword(s):  
Vortex Breakdown ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Tip Leakage Vortex ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Transonic Axial Compressor ◽  
Rotating Instability

The purpose of this study is to have a better understanding of the unsteady behavior of tip clearance flow at near-stall condition from a multi-passage simulation and to clarify the relation between such unsteadiness and rotating disturbance. This study is motivated by the following concern. A single passage simulation has revealed the occurrence of the tip leakage vortex breakdown at near-stall condition in a transonic axial compressor rotor, leading to the unsteadiness of the tip clearance flow field in the rotor passage. These unsteady flow phenomena were similar to those in the rotating instability, which is classified in one of the rotating disturbances. In other words it is possible that the tip leakage vortex breakdown produces a rotating disturbance such as the rotating instability. Three-dimensional unsteady RANS calculation was conducted to simulate the rotating disturbance in a transonic axial compressor rotor (NASA Rotor 37). The four-passage simulation was performed so as to capture a short length scale disturbance like the rotating instability and the spike-type stall inception. The simulation demonstrated that the unsteadiness of tip leakage vortex, which was derived from the vortex breakdown at near-stall condition, invoked the rotating disturbance in the rotor, which is similar to the rotating instability.

3-D Digital PIV Measurements of the Tip Clearance Flow in an Axial Compressor

2002 ◽  
Author(s):  
Mark P. Wernet ◽  
Dale Van Zante ◽  
Tony J. Strazisar ◽  
W. Trevor John ◽  
P. Susan Prahst
Keyword(s):  
Three Dimensional ◽  
Axial Compressor ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Image Velocimetry ◽  
Clearance Flow ◽  
Compressor Performance ◽  
Tip Clearance Vortex

The accurate characterization and simulation of rotor tip clearance flows has received much attention in recent years due to their impact on compressor-performance and stability. At NASA Glenn the first known three dimensional Digital Particle Image Velocimetry (DPIV) measurements of the tip region of a low speed compressor rotor have been acquired to characterize the behavior of the rotor tip clearance flow. The measurements were acquired phase-locked to the rotor position so that changes in the tip clearance vortex position relative to the rotor blade can be seen. The DPIV technique allows the magnitude and relative contributions of both the asynchronous motions of a coherent structure and the temporal unsteadiness to be evaluated. Comparison of measurements taken at the peak efficiency and at near stall operating conditions characterizes the mean position of the clearance vortex and the changes in the unsteady behavior of the vortex with blade loading. Comparisons of the 3-D DPIV measurements at the compressor design point to a 3D steady N-S solution are also done to assess the fidelity of steady, single-passage simulations to model an unsteady flow field.

The Behavior of Tip Clearance Flow at Near-Stall Condition in a Transonic Axial Compressor Rotor

2007 ◽  
Author(s):  
K. Yamada ◽  
K. Funazaki ◽  
M. Furukawa
Keyword(s):  
Boundary Layer ◽  
Shock Wave ◽  
Axial Compressor ◽  
Boundary Layer Separation ◽  
Tip Clearance ◽  
Suction Surface ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Transonic Axial Compressor

It is known that the tip clearance flow is dominant and very important flow phenomena in axial compressor aerodynamics because the tip clearance flow has a great influence on the stability as well as aerodynamic loss of compressors. Our goal is to clarify the behavior of tip clearance flow at near-stall condition in a transonic axial compressor rotor (NASA Rotor 37). In the present work, steady and unsteady RANS simulations were performed to investigate vortical flow structures and separated flow field near the tip for several different clearance cases. Boundary layer separation on the casing wall and blade suction surface was investigated in detail for near-stall and stall condition. In order to understand such complicated flow field, vortex cores were identified using the critical point theory and a topology of the three-dimensional separated and vortical flows was analyzed. In the nominal clearance case, the breakdown of tip leakage vortex has occurred at a near-stall operating condition because of the interaction of the vortex with the shock wave, leading to a large blockage and unsteadiness in the rotor tip. On the other hand, the calculation with no clearance suggested that the separation on the suction surface was different from that with the nominal clearance. Since the shock wave induced the boundary layer separation on the blade suction surface in the transonic axial compressor rotor, focal-type critical points appeared on the suction surface near the tip at near-stall condition.

Effect of tip clearance size on the performance of a low-reaction transonic axial compressor rotor

2019 ◽  
Vol 234 (2) ◽  
pp. 127-142
Author(s):  
Wei Zhu ◽  
Songtao Wang ◽  
Longxin Zhang ◽  
Jun Ding ◽  
Zhongqi Wang
Keyword(s):  
Numerical Simulations ◽  
Dynamic Balance ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Flow Phenomena

This study aimed to enhance the understanding of flow phenomena in low-reaction aspirated compressors. Three-dimensional, multi-passage steady and unsteady numerical simulations are performed to investigate the performance sensitivity to tip clearance variation on the first-stage rotor of a multistage low-reaction aspirated compressor. Three kinds of tip clearance sizes including 1.0τ, 2.0τ and 3.0τ are modeled, in which 1.0τ corresponds to the designed tip clearance size of 0.2 mm. The steady numerical simulations show that the overall performance of the rotor moves toward lower mass flow rate when the tip clearance size is increased. Moreover, energy losses, efficiency reduction and stall margin decrease are also observed with increasing tip clearance size. This can be mostly attributed to the damaging impact of intense tip clearance flow. For unsteady simulation, the result shows periodical oscillation of the tip leakage vortex and a “two-passage periodic structure” in the tip region at the near-stall point. The occurrence of the periodical oscillation is due to the severe interaction between the tip clearance flow and the shock wave. However, the rotor operating state is still stable at this working point because a dynamic balance is established between the tip clearance flow and incoming flow.

Unsteady tip clearance flow pattern in an isolated axial compressor rotor with micro tip injection

2007 ◽  
Vol 16 (4) ◽  
pp. 309-320 ◽  
Author(s):  
Shaojuan Geng ◽  
Hongwu Zhang ◽  
Jingyi Chen ◽  
Weiguang Huang
Keyword(s):  
Flow Pattern ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Tip Injection

Numerical simulation of unsteady tip clearance flow in an isolated axial compressor rotor blades row

2011 ◽  
Vol 226 (1) ◽  
pp. 82-93 ◽  
Author(s):  
R Taghavi-Zenouz ◽  
S Eslami
Keyword(s):  
Experimental Data ◽  
Axial Compressor ◽  
Rotor Blades ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Clearance Flow

Three-dimensional unsteady numerical simulations were carried out to analyse tip clearance flow in a low-speed isolated axial compressor rotor blades row. A flow solver has been used for the current study utilizing the large eddy simulation (LES) technique. Periodic tip leakage flow and its propagation trajectories were simulated in detail. A number of pseudo pressure transducers were imposed on the pressure side of the blade for detection of unsteady surface pressures to provide a calculation of tip leakage flow frequencies. Two different sizes of tip clearance were considered for simulations and analyses. Non-dimensional frequencies of the tip leakage flow were calculated and final results were compared to those of existing numerical and experimental data. Final results demonstrated that in contrast to the Reynolds averaged Navier–Stokes (RANS) model, the LES method shows considerable dependency of frequency characteristics of the tip leakage flow to the gap size and can detect different frequency spectrums along the blade surface. All the results obtained through the current numerical approach were in close agreement with those of existing experimental data.

CFD Code Validation and Qualitative Study of Effects of Tip Clearance Variation on Performance of Transonic Axial Compressor Rotor

2012 ◽  
Author(s):  
Aniket R. Patkar ◽  
Srinivethan Rangasamy ◽  
Sreekanth Raghunath ◽  
Vilas Kalamkar
Keyword(s):  
Pressure Ratio ◽  
Splitting Method ◽  
Flow Characteristics ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Maximum Pressure ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Transonic Axial Compressor ◽  
Multiple Frame

The main objective of this work is the validation of Computational Fluid Dynamics (CFD) code used for analysis of transonic axial compressors. NASA Rotor 35 is used here as test case for validation. In this work, computations are performed using parallelized RANS code, to predict the transonic axial compressor rotor flow characteristics. Advection Upstream Splitting Method (AUSM) scheme has been used. A Multiple Frame of Reference approach has been used to model the rotor passage. Spalart-Allmaras turbulence model is used to model turbulence. Multiblock Structured mesh is used. Performance characteristics for the entire range of operation, from maximum mass flow rate till maximum pressure ratio, have been simulated. The results obtained are comparable with experimental data within 5–10% error. Investigations have been carried out to study the effect of varying tip clearance in NASA Rotor 35. The present work is intended to study the clearance flow trajectory as a function of varying tip clearance. The effects of shock/vortex interaction in tip clearance region are also studied. The effects of tip clearance size on the generation and evolution of the end-wall vortical structures are discussed by investigating their evolutionary trajectories. By this study, it is observed that as tip clearance reduces, clearance flow trajectory moves downstream. From this it can be concluded that if tip clearance increases, tip clearance vortices expand. This may help in casing-treatment or tip-treatment to mitigate the loss in the performance, if the tip clearance increases.

Short Length-Scale Rotating Stall Inception in a Transonic Axial Compressor: Experimental Investigation

2006 ◽  
Author(s):  
Jo¨rg Bergner ◽  
Matthias Kinzel ◽  
Heinz-Peter Schiffer ◽  
Chunill Hah
Keyword(s):  
Experimental Investigation ◽  
Axial Compressor ◽  
Rotating Stall ◽  
Wall Pressure ◽  
Tip Clearance ◽  
Stall Inception ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
Contour Plots ◽  
Transonic Axial Compressor

To improve the understanding of spike-type stall inception of a transonic axial compressor, measurements of the unsteady static pressure in the rotor endwall region are analyzed. At design speed, a detailed experimental investigation of the unsteadiness of the pressure field at the rotor endwall at near stall condition shows a strong fluctuation of the tip clearance flow. Both vortex strength and -trajectory oscillate randomly. Analysis of the wall pressure time histories during stall inception suggests that spike-type disturbances of the flow field correlate with an upstream motion of one blade passages shock front. In addition, the evolution of a stall cell could be visualized by means of static wall-pressure contour plots.

The Flow Field in the Tip Clearance Region of an Axial Compressor Rotor

1999 ◽  
Author(s):  
Toshiyuki Arima ◽  
Masatoshi Shirotori ◽  
Yoshihiro Yamaguchi
Keyword(s):  
Flow Field ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Grid Topology ◽  
Clearance Flow ◽  
Inflow Condition ◽  
Blade Tip ◽  
Single Block

A three-dimensional, Reynolds-averaged, compressible Navier-Stokes analysis (using a multi-block grid with the grid embedded in the tip-clearance space) has been developed to study the tip-clearance flow of an axial compressor rotor. A low-Reynolds number k-ε model have been used to reproduce the effects of turbulence. In order to assess the effect of the tip-clearance-grid treatment on prediction for the tip-clearance flow, calculations using a single-block grid (pinched grid topology) and multi-block grid (embedded grid topology) have been performed to calculate the flow field of NASA Rotor 37. The results are compared with experimental data. It has been found that both the single-block and multi-block approaches give a good agreement with the experimental data regarding the overall performance map of the rotor. For the prediction of the spanwise distributions of averaged aerodynamic properties downstream of the rotor, however, the orderly grid over the blade tip associated with the embedded grid has produced accurate predictions particularly from 40% to 80% span. In order to investigate the tip-clearance flow for different operating conditions, calculations have been performed for conditions at 100% (transonic inflow condition) and 60% (subsonic inflow condition) of the design point speed. Computed limiting streamlines at the blade tip surface and particle traces released from the tip-clearance have been used to study the tip-clearance flow. At the 100% speed, both separation and reattachment lines have been observed and a separation bubble occurs. At the 60% speed, the separation line shifts to the blade pressure side and the reattachment line can be partly observed near the leading edge of the blade tip surface. In order to investigate the interaction of the leakage vortex from the tip clearance with the main flow, the computed secondary flows on the cross-flow sections have been analyzed at the 100% and the 60% speeds. At the 100% speed, the vortex core apparently increases in size, as it moves downstream. At 60% speed, the second vortex, first reported by Suder and Celestina in 1994, is barely observable. Furthermore, the trajectory of vortex core identified using a semi-analytical method has also been used to study the vortex motion in the flow field near the blade tip.

Sign in / Sign up

Export Citation Format

Share Document