Injection Characteristics of Coal-Water Slurries in Medium-Speed Diesel Equipment

1992 ◽  
Vol 114 (3) ◽  
pp. 522-527 ◽  
Author(s):  
L. G. Dodge ◽  
T. J. Callahan ◽  
T. W. Ryan ◽  
J. A. Schwalb ◽  
C. E. Benson ◽  
...  
Keyword(s):  
Diesel Fuel ◽  
Cone Angle ◽  
Injection Pressure ◽  
Elevated Pressure ◽  
Injection System ◽  
Spray Characteristics ◽  
Minimal Impact ◽  
Jet Mixing ◽  
High Injection ◽  
Injection Pressures

The injection characteristics of several micronized coal-water slurries (CWSs, where “s” implies plural) were investigated at high injection pressures (40 to 140 MPa, or 6,000 to 20,000 psi). Detailed spray characteristics including drop-size distributions and cone angles were measured using a continuous, high-pressure injection system spraying through various hole shapes and sizes into a continuous, elevated-pressure air flow. Penetration and cone angle were also measured using intermittent injection into an elevated-pressure quiescent chamber. Cone angles and fuel-air mixing increased rapidly with the relatively constant cone angles of diesel fuel. However, even at high injection pressures the CWSs mixed with air more slowly than diesel fuel at the same pressure. The narrower CWS sprays penetrated more rapidly than diesel fuel at the same injection pressures. Increasing injection pressure dramatically reduced drop sizes in the CWS sprays, while increasing injection pressure reduced drop sizes in the diesel fuel sprays more gradually. The CWSs produced larger average drop sizes than the diesel fuel at all conditions, except for some hole shapes at the highest injection pressures where the average sizes were about the same. Varying the hole shape using converging and diverging holes had a minimal impact on the spray characteristics. A turbulent jet mixing model was used to predict the penetration rate of the CWS fuel jets through different orifice sizes and into different air densities. The jet model also computes the liquid fuel-air ratio through the jet. The work reported here was abstracted from the more complete report by Schwalb et al. (1991).

Effect of Injection Parameters on the Spray Characteristics of DME Fuel

2006 ◽  
Author(s):  
Bong Woo Ryu ◽  
Seung Hwan Bang ◽  
Hyun Kyu Suh ◽  
Chang Sik Lee
Keyword(s):  
Dimethyl Ether ◽  
Diesel Fuel ◽  
Cone Angle ◽  
Injection Pressure ◽  
Injection Rate ◽  
Spray Characteristics ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Injection Duration ◽  
Injection Parameters

The purpose of this study is to investigate the effect of injection parameters on the injection and spray characteristics of dimethyl ether and diesel fuel. In order to analyze the injection and spray characteristics of dimethyl ether and diesel fuel with employing high-pressure common-rail injection system, the injection characteristics such as injection delay, injection duration, and injection rate, spray cone angle and spray tip penetration was investigated by using the injection rate measuring system and the spray visualization system. In this work, the experiments of injection rate and spray visualization are performed at various injection parameters. It was found that injection quantity was decreased with the increase of injection pressure at the same energizing duration and injection pressure In the case of injection characteristics, dimethyl ether showed shorter of injection delay, longer injection duration and lower injected mass flow rate than diesel fuel in accordance with various energizing durations and injection pressures. Also, spray development of dimethyl ether had larger spray cone angle than that of diesel fuel at various injection pressures. Spray tip penetration was almost same development and tendency regardless of injection angles.

Experimental study of spray characteristics of biodiesel blending with diethyl carbonate in a common rail injection system

2017 ◽  
Vol 233 (2) ◽  
pp. 249-262 ◽  
Author(s):  
Wei Fu ◽  
Lanbo Song ◽  
Tao Liu ◽  
Qizhao Lin
Keyword(s):  
Cone Angle ◽  
Injection Pressure ◽  
Injection System ◽  
Diethyl Carbonate ◽  
Spray Characteristics ◽  
Projected Area ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Common Rail Injection System ◽  
Common Rail Injection

The objective of this paper is to investigate the spray macroscopic characteristics of biodiesel, diethyl carbonate (DEC)-biodiesel blends and diesel fuel based on a common-rail injection system. The spray tip penetration, spray cone angle and the spray projected area were measured through a high-speed photography method. The experimental results reveal that injection pressure and ambient pressure have significant effects on the spray characteristics. Higher injection pressure makes the spray tip penetration increase, while higher back pressure inside the chamber leads to the enlargement of the spray cone angle. The addition of DEC causes the blends fuels to have a shorter penetration and larger spray projected area, which reveals the potential capacity to improve the atomization process compared with biodiesel. The estimation of spray droplet size indicates that DEC30 generates a smaller Sauter mean diameter (SMD) because of its lower surface tension and viscosity. Model predictions were illustrated and compared with current work.

Effect of ultra-high injection pressure up to 50 MPa on macroscopic spray characteristics of a multi-hole gasoline direct injection injector fueled with ethanol

2017 ◽  
Vol 232 (8) ◽  
pp. 1092-1104 ◽  
Author(s):  
Xiang Li ◽  
Yi-qiang Pei ◽  
Jing Qin ◽  
Dan Zhang ◽  
Kun Wang ◽  
...  
Keyword(s):  
High Speed ◽  
Direct Injection ◽  
Cone Angle ◽  
Injection Pressure ◽  
Fuel Mixture ◽  
Gasoline Direct Injection ◽  
Spray Characteristics ◽  
High Injection ◽  
High Injection Pressure ◽  
Wall Impingement

This research systematically studied the effect of injection pressure on macroscopic spray characteristics of a five-hole gasoline direct injection (GDI) injector fueled with ethanol, especially under ultra-high injection pressure up to 50 MPa. The front and side views of sprays were photographed by the schlieren method using a high-speed camera. Various parameters, including spray development stages, cone angle, penetration, area and irregular ratio, were fully analyzed to evaluate macroscopic characteristics of the whole spray and spray core with varying injection pressure. The results demonstrated that the effect of ultra-high injection pressure on macroscopic spray characteristics was significant. As injection pressure increased from 10 MPa to 50 MPa, the occurrence time of branch-like structure decreased; the cone angle increased little; the area increased significantly; the area ratio dropped by 6.4 and 5.8 percentage points on average for the front view and side view spray, respectively. There was a significant increase in the trend for penetration as the injection pressure rose from 10 MPa to 30 MPa. However, this trend became weak when the injection pressure further increased. The penetration ratio under ultra-high injection pressure was slightly higher than it was under 10 or 20 MPa. Ultra-high injection pressure would not obviously raise the possibility of spray/wall impingement, but led to the impingement quantity increasing to some extent. Increasing injection pressure could enhance the vortex scale, finally resulting in better air/fuel mixing quality. Ultra-high injection pressure was a potential way to improve air/fuel mixture homogeneity for a GDI injector fueled with ethanol.

SPRAY VISUALIZATION OF HYDROTREATED VEGETABLE OIL UNDER SIMULATED DIESEL ENGINE CONDITION

2020 ◽  
Vol 40 (04) ◽  
Author(s):  
VO TAN CHAU
Keyword(s):  
Vegetable Oil ◽  
Diesel Fuel ◽  
Alternative Fuels ◽  
Cone Angle ◽  
Injection Pressure ◽  
Fuel Properties ◽  
Spray Characteristics ◽  
Spray Cone Angle ◽  
Penetration Length ◽  
Spray Cone

The diversity of alternative fuels and the corresponding variation in their physical and chemical properties, coupled with simultaneous changes in advanced techniques for CI-engine, needed to improve engine efficiency and emissions. Hydrotreated Vegetable Oil (HVO), seen as a promising substitution for petrol-diesel, and diesel fuel (mixed of 7% palm-biodiesel or B7) were analyzed on fuel properties. Then, the influence of these fuel properties on spray characteristics in constant volume combustion chamber were evaluated under conditions of single hole injector of 200m diameter, injection pressure of 100MPa, constant back pressure of 4.0MPa and energizing time of 2.5ms. The results show that HVO had smaller in viscosity (18.48%), density (5.52%), sulfur content, distillation under T50, T90 and higher in derived cetane index (27.2%), heating value (2.2%), respectively, compared to diesel. Spray characteristics of HVO had the same propensity with diesel fuel. HVO revealed a slightly shorter in penetration length (5%) during fully developed zone, a larger spray cone angle (from 0.2 to 1.1 degree wider in quasi-steady state). Both fuels had a similar maximum spray velocity reaching at 5mm to 10mm from nozzle orifice. Also observed was an increase in spray volume of HVO.

Spray Characterization of Palm Olein/Diesel Blends under Various Injection Pressures

2013 ◽  
Vol 647 ◽  
pp. 645-653
Author(s):  
M.H.A.R Mantari ◽  
Y.A. Eldrainy ◽  
Mohammad Nazri Mohd Jaafar
Keyword(s):  
Diesel Fuel ◽  
Palm Olein ◽  
Cone Angle ◽  
Atmospheric Condition ◽  
Injection Pressure ◽  
Spray Angle ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Swirl Atomizer ◽  
Injection Pressures

The Sauter Mean Diameter (SMD) and spray cone angle are two important parameters that characterize spray performance. The objective of this study is to characterize palm olein/diesel blends spray in terms of spray angle and SMD under different injection pressures using a hollow cone pressure swirl atomizer. The physical properties of five diesel/palm olein blends, namely B5, B10, B15, B20 and B25 were measured and their spray characteristics were tested at injection pressures of 0.8MPa, 1.0MPa, and 1.2MPa under ambient atmospheric condition. The results were compared to spray established using petroleum diesel fuel. The SMD was measured using a phase Doppler analyzer (PDA). The spray cone angle was visualized using a digital single-lens reflex (DSLR) camera. The results indicated that petroleum diesel fuel had the widest cone angle followed by B5, B10, B15, B20 and B25 under the same injection pressure. Additionally, when the injection pressure increases from 0.8MPa to 1.2MPa, the spray cone angle widen accordingly. It is concluded that high content of palm olein in the palm biofuel blends increases viscosity and surface tension and hence higher value of SMD and narrower spray cone angle was generated. An increase in injection pressure resulted in smaller droplet SMD and wider spray cone angle.

scholarly journals Experimental Study of Spray Characteristics of Kerosene-Ethanol Blends from a Pressure-Swirl Nozzle

2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
Tao Zhang ◽  
Bo Dong ◽  
Xun Zhou ◽  
Linan Guan ◽  
Weizhong Li ◽  
...  
Keyword(s):  
Discharge Coefficient ◽  
Cone Angle ◽  
Injection Pressure ◽  
Spray Characteristics ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Breakup Length ◽  
Ethanol Blends ◽  
Pressure Swirl ◽  
Spray Velocity

Partial replacement of kerosene by ethanol in a gas turbine is regarded as a good way to improve the spray quality and reduce the fossil energy consumption. The present work is aimed at studying the spray characteristics of kerosene-ethanol blends discharging from a pressure-swirl nozzle. The spray cone angle, discharge coefficient, breakup length, and velocity distribution are obtained by particle image velocimetry, while droplet size is acquired by particle/droplet imaging analysis. Kerosene, E10 (10% ethanol, 90% kerosene), E20 (20% ethanol, 80% kerosene), and E30 (30% ethanol, 70% kerosene) have been considered under the injection pressure of 0.1–1 MPa. The results show that as injection pressure is increased, the discharge coefficient and breakup length decrease, while the spray cone angle, drop size, and spray velocity increase. Meanwhile, the drop size decreases and the spray velocity increases with ethanol concentration when the injection pressure is lower than 0.8 MPa. However, the spray characteristics are not affected obviously by the ethanol concentration when the injection pressure exceeds 0.8 MPa. A relation to breakup length for kerosene-ethanol blends is obtained. The findings demonstrate that the adding of ethanol into kerosene can promote atomization performance.

Sign in / Sign up

Export Citation Format

Share Document