Using Transient Inflow Performance Relationships to Model the Dynamic Interaction Between Reservoir and Wellbore During Pressure Testing

2008 ◽  
Vol 130 (4) ◽  
Author(s):  
Aldo Costantini ◽  
Gioia Falcone ◽  
Geoffrey F. Hewitt ◽  
Claudio Alimonti
Keyword(s):  
Multiphase Flow ◽  
Flow Rate ◽  
Flow Behavior ◽  
Dynamic Interaction ◽  
Published Data ◽  
Preliminary Evaluation ◽  
Well Test ◽  
Inflow Performance ◽  
Transient Multiphase Flow ◽  
Bottomhole Pressure

The fundamental understanding of the dynamic interactions between multiphase flow in the reservoir and that in the wellbore remains surprisingly weak. The classical way of dealing with these interactions is via inflow performance relationships (IPRs), where the inflow from the reservoir is related to the pressure at the bottom of the well, which is a function of the multiphase flow behavior in the well. A steady-state IPRs are normally adopted, but their use may be erroneous when transient multiphase flow conditions occur. The transient multiphase flow in the wellbore causes problems in well test interpretation when the well is shut-in at the surface and the bottomhole pressure is measured. The pressure buildup (PBU) data recorded during a test can be dominated by transient wellbore effects (e.g., phase change, flow reversal, and re-entry of the denser phase into the producing zone), making it difficult to distinguish between true reservoir features and transient wellbore artifacts. This paper introduces a method to derive the transient IPRs at bottomhole conditions in order to link the wellbore to the reservoir during PBU. A commercial numerical simulator was used to build a simplified reservoir model (single well, radial coordinates, homogeneous rock properties) using published data from a gas condensate field in the North Sea. In order to exclude wellbore effects from the investigation of the transient inflow from the reservoir, the simulation of the wellbore was omitted from the model. Rather than the traditional flow rate at surface conditions, bottomhole pressure was imposed to constrain the simulation. This procedure allowed the flow rate at the sand face to be different from zero during the early times of the PBU, even if the surface flow rate is equal to zero. As a result, a transient IPR at bottomhole conditions was obtained for the given field case and for a specific set of time intervals, time steps, and bottomhole pressure. In order to validate the above simulation approach, a preliminary evaluation of the required experimental setup was carried out. The setup would allow the investigation of the dynamic interaction between the reservoir, the near-wellbore region, and the well, represented by a pressured vessel, a cylindrical porous medium, and a vertical pipe, respectively.

Using Transient Inflow Performance Relationships to Model the Dynamic Interaction Between Reservoir and Wellbore During Pressure Testing

2007 ◽  
Author(s):  
Aldo Costantini ◽  
Gioia Falcone ◽  
Geoffrey F. Hewitt ◽  
Claudio Alimonti
Keyword(s):  
Multiphase Flow ◽  
Flow Rate ◽  
Dynamic Interaction ◽  
Published Data ◽  
Preliminary Evaluation ◽  
Well Test ◽  
Set Up ◽  
Inflow Performance ◽  
Transient Multiphase Flow ◽  
Bottomhole Pressure

The fundamental understanding of the dynamic interactions between multiphase flow in the reservoir and that in the wellbore remains surprisingly weak. The classical way of dealing with these interactions is via inflow performance relationships (IPR’s), where the inflow from the reservoir is related to the pressure at the bottom of the well, which is a function of the multiphase flow behaviour in the well. Steady-state IPR’s are normally adopted, but their use may be erroneous when transient multiphase flow conditions occur. Transient multiphase flow in the wellbore causes problems in well test interpretation when the well is shut-in at surface and the bottomhole pressure is measured. Pressure build-up (PBU) data recorded during a test can be dominated by transient wellbore effects (e.g. phase change, flow reversal and re-entry of the denser phase into the producing zone), making it difficult to distinguish between true reservoir features and transient wellbore artefacts. This paper introduces a method to derive the transient IPR’s at bottomhole conditions in order to link the wellbore to the reservoir during PBU. A commercial numerical simulator was used to build a simplified reservoir model (single well, radial co-ordinates, homogeneous rock properties) using published data from a gas condensate field in the North Sea. In order to exclude wellbore effects from the investigation of the transient inflow from the reservoir, the simulation of the wellbore was omitted from the model. Rather than the traditional flow rate at surface conditions, bottomhole pressure was imposed to constrain the simulation. This procedure allowed the flow rate at the sand face to be different from zero during the early times of the PBU, even if the surface flow rate is equal to zero. As a result, a transient IPR at bottomhole conditions was obtained for the given field case and for a specific set of time intervals, time steps and bottomhole pressure. In order to validate the above simulation approach, a preliminary evaluation of the required experimental set-up was carried out. The set-up would allow the investigation of the dynamic interaction between the reservoir, the near-wellbore region and the well, represented by a pressured vessel, a cylindrical porous medium and a vertical pipe, respectively.

Unloading Frac Hits in Gas Wells: How Does the Nitrogen Injection Rate and Pressure Affect the Unloading Process?

2021 ◽  
Author(s):  
Miguel Angel Cedeno
Keyword(s):  
Multiphase Flow ◽  
Flow Rate ◽  
Injection Pressure ◽  
Injection Rate ◽  
Gas Wells ◽  
Eagle Ford Shale ◽  
Eagle Ford ◽  
Nitrogen Injection ◽  
Injection Flow ◽  
Transient Multiphase Flow

Abstract The unconventional resources development has grown tremendously as a result of the advancement in horizontal drilling technology coupled with hydraulic fracturing. However, as more wells are drilled and fractured close to each other, frac hits have become a major challenge in these wells. The aim of this work is to investigate the effect of nitrogen injection flow rate and pressure on unloading frac hits gas wells in transient multiphase flow. A numerical simulation model was created using a transient multiphase flow simulator to mimic the unloading process of frac hits by injecting nitrogen from the surface through the annulus section of the well. Many simulation cases were created and analyzed to comprehend the effect of the nitrogen injection rate and pressure on the unloading of frac hits. The model mimicked real field data from currently active well in the Eagle Ford Shale. The results showed that as the nitrogen injection pressure increases, the nitrogen volume and the time to unload the frac hits decrease. On the other hand, increasing the injection rate of nitrogen will increase the nitrogen volume required to unload the frac hits. In addition, the time to unload frac hits will be decreased as the nitrogen injection rate increases. These results indicate that the time required to unload frac hits will be minimized if higher flow rates of nitrogen were utilized. Nonetheless, the volume of nitrogen required to unload the frac hits will be maximized. An important observation to highlight is that the operators can save money by reducing the time for injecting nitrogen. This observation was verified when increasing the injection pressure in the frac hit well in the Eagle Ford Shale, the time of injection was reduced 20%. This study presents the effects of nitrogen injection flow rate and injection pressure for unloading frac hits in gas wells. Due to the lack of published studies about this topic, this work can serve as a practical guideline for unloading frac hits in gas wells.

scholarly journals Analisis Performance Sumur X Menggunakan Metode Standing Dari Data Pressure Build Up Testing

2016 ◽  
Vol 5 (2) ◽  
pp. 57-61
Author(s):  
Novrianti Novrianti
Keyword(s):  
Flow Rate ◽  
Maximum Flow ◽  
Maximum Flow Rate ◽  
Well Test ◽  
Time Data ◽  
Constant Flow Rate ◽  
Optimal Flow ◽  
Production Wells ◽  
Inflow Performance

The number of production wells refers to the performance of the well, which is shown in the graph of inflow performance relationship (IPR). Reservoir characteristics influence on performance of the well, type of welltest and methods that be used in the determination of IPR. By using the IPR curves, maximum flow rate and the optimal flow rate of the well will be known. Pressure Build Up test is used to know performance and a maximum flow rate of the X well. Well test conducted for 15 hours. The well produced at a constant flow rate than close the wellhead. The Pressure data and time data obtained from the well test. The result of Pressure build-up testing analysis among permeability, skin and flow efficiency. After analyzing the Pressure build-up testing permeability obtained 190 mD, skin + 1,68 and 0,83 flow efficiency. Based on the value of flow efficiency Standing method is the most appropriate method is used to analyze the productivity of X well. Standing appropriate method for wells with skin ≠ 0 and flow efficiency ≠ 1. The maximum flow rate of the X well using Standing Method on the 0,83 flow efficiency was 13,91 MMSCFD

Investigation on the control of multiphase flow behavior in a continuous casting tundish during ladle change

2020 ◽  
Vol 117 (6) ◽  
pp. 619
Author(s):  
Rui Xu ◽  
Haitao Ling ◽  
Haijun Wang ◽  
Lizhong Chang ◽  
Shengtao Qiu
Keyword(s):  
Multiphase Flow ◽  
Flow Behavior ◽  
Rolled Strip ◽  
Impact Zone ◽  
Steel Cleanliness ◽  
Carry Over ◽  
Slag Carry Over ◽  
Hot Rolled ◽  
Turbulence Inhibitor ◽  
The Impact

The transient multiphase flow behavior in a single-strand tundish during ladle change was studied using physical modeling. The water and silicon oil were employed to simulate the liquid steel and slag. The effect of the turbulence inhibitor on the slag entrainment and the steel exposure during ladle change were evaluated and discussed. The effect of the slag carry-over on the water-oil-air flow was also analyzed. For the original tundish, the top oil phase in the impact zone was continuously dragged into the tundish bath and opened during ladle change, forming an emulsification phenomenon. By decreasing the liquid velocities in the upper part of the impact zone, the turbulence inhibitor decreased considerably the amount of entrained slag and the steel exposure during ladle change, thereby eliminating the emulsification phenomenon. Furthermore, the use of the TI-2 effectively lowered the effect of the slag carry-over on the steel cleanliness by controlling the movement of slag droplets. The results from industrial trials indicated that the application of the TI-2 reduced considerably the number of linear inclusions caused by ladle change in hot-rolled strip coils.

scholarly journals Computational Investigation of Inclusion Removal in the Steel-Refining Ladle Process

Processes ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 1048
Author(s):  
Xipeng Guo ◽  
Joel Godinez ◽  
Nicholas J. Walla ◽  
Armin K. Silaen ◽  
Helmut Oltmann ◽  
...  
Keyword(s):  
Multiphase Flow ◽  
Porous Plug ◽  
Cfd Modeling ◽  
Balance Model ◽  
Computational Investigation ◽  
Inclusion Removal ◽  
Inclusion Interaction ◽  
Computational Fluid Dynamics Cfd ◽  
Steel Refining ◽  
Transient Multiphase Flow

In a steel-refining ladle, the properties of manufactured steel can be notably degraded due to the presence of excessive inclusions. Stirring via gas injection through a porous plug is often used as part of the steel-refining process to reduce these inclusions. In this paper, 3D computational fluid dynamics (CFD) modeling is used to analyze transient multiphase flow and inclusion removal in a gas-stirred ladle. The effects of gas stirring with bubble-inclusion interaction are analyzed using the Euler–Euler approach for multiphase flow modeling, while the effects of inclusions aggregation and removal are modeled via a population balance model (PBM).

Effect of Surface State of Die on Flow Rate of Steamed Bamboo Powder in Thermal Flow Test Using Capillary Rheometer

2015 ◽  
Vol 651-653 ◽  
pp. 830-835
Author(s):  
Shohei Kajikawa ◽  
Riku Sakagami ◽  
Takashi Iizuka
Keyword(s):  
Particle Size ◽  
Flow Rate ◽  
Surface State ◽  
Flow Behavior ◽  
Thermal Flow ◽  
Average Roughness ◽  
Arithmetic Average ◽  
Flow Test ◽  
Die Surface ◽  
Bamboo Powder

Thermal flow tests were performed on steamed bamboo powder using capillaries that were processed under different conditions in order to investigate the effect of the die surface state on the fluidity of the woody powder. The capillaries were processed by wire-cut electric discharge machining, reaming or drilling, and the arithmetic average roughness (Ra) varied from 0.5 to 2.5 μm. The bamboo powder was first steamed at 200 °C for 20 min, and its particle size was then controlled using different mesh screens. The thermal flow temperature was set at 200 °C. The results indicated that the flow behavior improved with increasing particle size. For the capillaries processed by WEDM, the flow rate for samples with particle sizes of 75~150 and 150~300 μm decreased with increasing Ra. On the other hand, when reaming or drilling was used to process the capillaries, the flow rate was almost independent of Ra, regardless of the particle size.

Design and Simulation of a Hybrid Entrained-Flow and Fluidized Bed Mild Gasifier: Part 2—Case Study and Analysis

2011 ◽  
Author(s):  
A. K. M. Monayem Mazumder ◽  
Ting Wang ◽  
Jobaidur R. Khan
Keyword(s):  
Multiphase Flow ◽  
Fluidized Bed ◽  
Flow Behavior ◽  
Flame Temperature ◽  
Heterogeneous Reactions ◽  
Thermal Flow ◽  
Entrained Flow ◽  
Progressive Development ◽  
Gasification Process ◽  
Flow And Heat Transfer

To help design a mild-gasifier, a reactive multiphase flow computational model has been developed in Part 1 using Eulerian-Eulerian method to investigate the thermal-flow and gasification process inside a conceptual, hybrid entrained-flow and fluidized-bed mild-gasifier. In Part 2, the results of the verifications and the progressive development from simple conditions without particles and reactions to complicated conditions with full reactive multiphase flow are presented. Development of the model starts from simulating single-phase turbulent flow and heat transfer in order to understand the thermal-flow behavior, followed by introducing seven global, homogeneous gasification reactions progressively added one equation at a time. Finally, the particles are introduced, and heterogeneous reactions are added in a granular flow field. The mass-weighted, adiabatic flame temperature is validated through theoretical calculation and the minimum fluidization velocity is found to be close to Ergun’s correlation. Furthermore, the predicted exit species composition is consistent with the equilibrium values.

PRELIMINARY EVALUATION OF PATIENT RADIATION DOSES DURING RADIONUCLIDE DIAGNOSTIC WITH MONOCLONAL ANTIBODIES LABELED WITH 89Zr

2021 ◽  
Author(s):  
Larisa A. Chipiga ◽  
Anna E. Petrova ◽  
Artem A. Mosunov ◽  
Laura T. Naurzbaeva ◽  
Stanislaus M. Kushnarenko ◽  
...  
Keyword(s):  
Monoclonal Antibodies ◽  
Dose Assessment ◽  
Published Data ◽  
Radiation Doses ◽  
Preliminary Evaluation ◽  
Software Products ◽  
Absorbed Doses ◽  
Order Of Magnitude ◽  
Effective Doses

In connection with the constantly increasing use of monoclonal antibodies labeled with 89Zr, in clinical practice, it is urgent to study their pharmacokinetics with the determination, based on the data obtained, of absorbed doses in tumor foci, as well as intact organs and tissues, and effective doses of patients. To date, there are a limited number of studies that provide patient doses for diagnostic examinations using 89Zr-labeled monoclonal antibodies. In this regard, the purpose of this work was to assess the biodistribution of various monoclonal antibodies (ramucirumab, trastuzumab, atezolizumab) labeled with 89Zr, based on published data, with subsequent calculation of absorbed doses in radiosensitive organs and tissues and effective doses of patients. Based on the analysis of experimental data on the biodistribution of monoclonal antibodies labeled with 89Zr for the diagnosis of oncological diseases from the available literature sources and our own assessments, it has been concluded that the results of the determination of absorbed in organs and tissues and effective doses are inconsistent. The absorbed doses in organs, according to different literature sources, vary up to an order of magnitude within one organ and reach 440 mGy per examination, the effective dose varies from 3 to 112 mSv per examination. This may be due to differences in study design, radiometry and dose assessment methods. Comparison with doses obtained on the basis of a general model of biodistribution of monoclonal antibodies demonstrates the possibility of using this model for a rough estimate of internal doses of patients. However, for a more accurate assessment, it is necessary to standardize approaches to the determination of internal radiation doses using the most effective methodological solutions and software products.

Modelling Complex Well Behaviour in the Field Using a Transient Multiphase Flow Simulator (Russian)

2018 ◽  
Author(s):  
Kanat Karatayev ◽  
Beibit Bissakayev ◽  
Tamer Saada ◽  
Benjamin Madeley ◽  
Alberto Brancolini ◽  
...  
Keyword(s):  
Multiphase Flow ◽  
Flow Simulator ◽  
Transient Multiphase Flow ◽  
Complex Well
Sign in / Sign up

Export Citation Format

Share Document