Full Coverage Film-Cooled Blading in High Temperature Gas Turbines: Cooling Effectiveness, Profile Loss and Thermal Efficiency

1980 ◽  
Vol 102 (4) ◽  
pp. 957-963 ◽  
Author(s):  
H. Hempel ◽  
R. Friedrich ◽  
S. Wittig
Keyword(s):  
Thermal Efficiency ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Specific Work ◽  
Cooling Effectiveness ◽  
Common Component ◽  
Full Coverage ◽  
Cooling Air Flow ◽  
Cooling Air ◽  
Profile Loss

Extending data obtained from hot gas cascade measurements on the cooling effectiveness and profile loss coefficients of full coverage film-cooled blading, use is made of similarity considerations to determine the heat transfer characteristics under actual engine conditions. Of primary interest are stationary gas turbines. Calculations are made for a four-stage single shaft gas turbine with air preheat and common component efficiencies. As a representative result it is found that for a pressure ratio of π = 10 a relative cooling air flow of approximately 8 percent will be required in rising the temperature from 1173 to 1573 K. The resulting relative improvement of the thermal efficiency is 24 percent and that of the specific work about 70 percent.

Modified Brayton Cycles Utilizing Alcohol Fuels

1982 ◽  
Vol 104 (2) ◽  
pp. 341-348 ◽  
Author(s):  
M. F. Bardon
Keyword(s):  
Thermal Efficiency ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Inlet Temperature ◽  
Specific Work ◽  
Brayton Cycle ◽  
Compression Process ◽  
Turbine Inlet Temperature ◽  
Optimum Pressure ◽  
Alcohol Fuels

It is already well known that alcohols can be burned in open-cycle gas turbines by direct firing in the combustor. This paper demonstrates however, that there are significant improvements in thermal efficiency possible by modifying the manner in which alcohols are used in Brayton cycle engines. It is shown that injection of the alcohol during the compression process can materially improve both thermal efficiency and specific work because of the intercooling effect of evaporation. Calculations are given which demonstrate the improvement theoretically possible at representative values of peak turbine inlet temperature. It is also shown that the optimum pressure ratio for both regenerated and unregenerated cycles is different when such compressor evaporative intercooling is used rather than simply injecting the fuel into the combustor.

Experimental and Numerical Investigations of the NEKOMIMI Film Cooling Technology

2012 ◽  
Author(s):  
Karsten Kusterer ◽  
Nurettin Tekin ◽  
Dieter Bohn ◽  
Takao Sugimoto ◽  
Ryozo Tanaka ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
Film Cooling ◽  
Gas Turbines ◽  
Mixing Processes ◽  
Cooling Effectiveness ◽  
Numerical Investigations ◽  
Hot Gas ◽  
Cooling Technology ◽  
Lift Off ◽  
Cooling Air

The improvement of the thermal efficiency of modern gas turbines can be achieved by reducing the required cooling air amount. Therefore, it is necessary to increase the cooling effectiveness, so that the available cooling air fulfils the cooling task even if the amount has been reduced. Due to experimental and numerical efforts, it is well understood today that aerodynamic mixing processes are enhanced by counter rotating vortices (CRV) in the cooling jets and lead to jet liftoff effects. Novel film cooling technologies focus on establishing anti-counter-rotating-vortices (ACRV) inside the cooling jet that prevent the hot gas from flowing underneath the jet and, thus, avoid the lift-off effect. One of these technologies is the NEKOMIMI film cooling, which is derived from the original double-jet film cooling (DJFC).

Optimization of Regenerated Gas Turbines

1996 ◽  
Vol 118 (3) ◽  
pp. 654-660 ◽  
Author(s):  
D. S. Beck
Keyword(s):  
Optimization Algorithm ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Automotive Applications

An algorithm for the optimization of regenerated gas turbines is given. For sets of inputs that are typical for automotive applications, the optimum cycle pressure ratio and a set of optimized regenerator parameters that maximize thermal efficiency are given. A second algorithm, an algorithm for sizing regenerators based on outputs of the optimization algorithm, is given. With this sizing algorithm, unique regenerator designs can be determined for many applications based on the presented optimization data. Results of example sizings are given. The data indicate that one core (instead of two cores) should be used to maximize thermal efficiency. The data also indicate that thermal efficiencies of over 50 percent should be achievable for automotive applications if ceramic turbines are used.

Pulsed Impingement Turbine Cooling and its Effect on the Efficiency of Gas Turbines With Pressure Gain Combustion

2020 ◽  
Author(s):  
Nicolai Neumann ◽  
Dieter Peitsch ◽  
Arne Berthold ◽  
Frank Haucke ◽  
Panagiotis Stathopoulos
Keyword(s):  
Gas Turbine ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Turbine Blades ◽  
Impingement Cooling ◽  
Turbine Cooling ◽  
Pressure Gain Combustion ◽  
Cooling Air ◽  
Gas Turbine Cycle ◽  
Cycle Efficiency

Abstract Performance improvements of conventional gas turbines are becoming increasingly difficult and costly to achieve. Pressure Gain Combustion (PGC) has emerged as a promising technology in this respect, due to the higher thermal efficiency of the respective ideal gas turbine cycle. Previous cycle analyses considering turbine cooling methods have shown that the application of pressure gain combustion may require more turbine cooling air. This has a direct impact on the cycle efficiency and reduces the possible efficiency gain that can potentially be harvested from the new combustion technology. Novel cooling techniques could unlock an existing potential for a further increase in efficiency. Such a novel turbine cooling approach is the application of pulsed impingement jets inside the turbine blades. In the first part of this paper, results of pulsed impingement cooling experiments on a curved plate are presented. The potential of this novel cooling approach to increase the convective heat transfer in the inner side of turbine blades is quantified. The second part of this paper presents a gas turbine cycle analysis where the improved cooling approach is incorporated in the cooling air calculation. The effect of pulsed impingement cooling on the overall cycle efficiency is shown for both Joule and PGC cycles. In contrast to the authors’ anticipation, the results suggest that for relevant thermodynamic cycles pulsed impingement cooling increases the thermal efficiency of Joule cycles more significantly than it does in the case of PGC cycles. Thermal efficiency improvements of 1.0 p.p. for pure convective cooling and 0.5 p.p. for combined convective and film with TBC are observed for Joule cycles. But just up to 0.5 p.p. for pure convective cooling and 0.3 p.p. for combined convective and film cooling with TBC are recorded for PGC cycles.

Advanced Gas Turbine and High Performance Gas-Steam Combined Cycle Plant With Blade Cooling Air Controlling

2006 ◽  
Author(s):  
Tadashi Tsuji
Keyword(s):  
Power Generation ◽  
Heat Exchanger ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Hot Water ◽  
Blade Cooling ◽  
Combined Cycle Plant ◽  
Cooling Air

Air cooling blades are usually applied to gas turbines as a basic specification. This blade cooling air is almost 20% of compressor suction air and it means that a great deal of compression load is not converted effectively to turbine power generation. This paper proposes the CCM (Cascade Cooling Module) system of turbine blade air line and the consequent improvement of power generation, which is achieved by the reduction of cooling air consumption with effective use of recovered heat. With this technology, current gas turbines (TIT: turbine inlet temperature: 1350°C) can be up-rated to have a relative high efficiency increase. The increase ratio has a potential to be equivalent to that of 1500°C Class GT/CC against 1350°C Class. The CCM system is designed to enable the reduction of blade cooling air consumption by the low air temperature of 15°C instead of the usual 200–400°C. It causes the turbine operating air to increase at the constant suction air condition, which results in the enhancement of power and thermal efficiency. The CCM is installed in the cooling air line and is composed of three stage coolers: steam generator/fuel preheater stage, heat exchanger stage for hot water supplying and cooler stage with chilled water. The coolant (chilled water) for downstream cooler is produced by an absorption refrigerator operated by the hot water of the upstream heat exchanger. The proposed CCM system requires the modification of cooling air flow network in the gas turbine but produces the direct effect on performance enhancement. When the CCM system is applied to a 700MW Class CC (Combined Cycle) plant (GT TIT: 135°C Class), it is expected that there will be a 40–80MW increase in power and +2–5% relative increase in thermal efficiency.

Highest-Efficient Film Cooling by Improved NEKOMIMI Film Cooling Holes: Part 1 — Ambient Air Flow Conditions

2013 ◽  
Author(s):  
Karsten Kusterer ◽  
Nurettin Tekin ◽  
Frederieke Reiners ◽  
Dieter Bohn ◽  
Takao Sugimoto ◽  
...  
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Air Flow ◽  
Ambient Air ◽  
Flow Conditions ◽  
Test Rig ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Technology ◽  
Cooling Air

In modern gas turbines, the film cooling technology is essential for the protection of the hot parts, in particular of the first stage vanes and blades of the turbine, against the hot gases from the combustion process in order to reach an acceptable life span of the components. As the cooling air is usually extracted from the compressor, the reduction of the cooling effort would directly result to an increased thermal efficiency of the gas turbine. Understanding of the fundamental physics of film cooling is necessary for the improvement of the state-of-the-art. Thus, huge research efforts by industry as well as research organizations have been undertaken to establish high efficient film cooling technologies. It is a today common knowledge that film cooling effectiveness degradation is caused by secondary flows inside the cooling jets, i.e. the Counter-Rotating Vortices (CRV) or sometimes also mentioned as kidney-vortices, which induce a lift-off of the jet. Further understanding of the secondary flow development inside the jet and how this could be influenced, has led to hole configurations, which can induce Anti-Counter-Rotating Vortices (ACRV) in the cooling jets. As a result, the cooling air remains close to the wall and is additionally distributed flatly along the surface. Beside different other technologies, the NEKOMIMI cooling technology is a promising approach to establish the desired ACRV. It consists of a combination of two holes in just one configuration so that the air is distributed mainly on two cooling air streaks following the special shape of the generated geometry. The original configuration was found to be difficult for manufacturing even by advanced manufacturing processes. Thus, the improvement of this configuration has been reached by a set of geometry parameters, which lead to configurations much easier to be manufactured but preserving the principle of the NEKOMIMI technology. Within a numerical parametric study several advanced configurations have been obtained and investigated under ambient air flow conditions similar to conditions for a wind tunnel test rig. By systematic variation of the parameters a further optimization with respect to highest film cooling effectiveness has been performed. A set of most promising configurations has been also investigated experimentally in the test rig. The best configuration outperforms the basic configuration by 17% regarding the overall averaged adiabatic film cooling effectiveness under the experimental conditions.

One-Dimensional Model to Quantify NOx Reduction in Gas Turbines Using EGR

1998 ◽  
Author(s):  
K. K. Botros ◽  
M. J. de Boer ◽  
G. Kibrya
Keyword(s):  
Gas Turbine ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Nox Reduction ◽  
Simulation Software ◽  
Specific Work ◽  
Dimensional Model ◽  
Nox Formation ◽  
One Dimensional ◽  
Thermal Nox

A one dimensional model based on fundamental principles of gas turbine thermodynamics and combustion processes was constructed to quantify the principle of exhaust gas recirculation (EGR) for NOx reduction. The model utilizes the commercial process simulation software ASPEN PLUS®. Employing a set of 8 reactions including the Zeldovich mechanism, the model predicted thermal NOx formation as function of amount of recirculation and the degree of recirculate cooling. Results show that addition of sufficient quantities of uncooled recirculate to the inlet air (i.e. EGR>∼4%) could significantly decrease NOx emissions but at a cost of lower thermal efficiency and specific work. Cooling the recirculate also reduced NOx at lower quantities of recirculation. This has also the benefit of decreasing losses in the thermal efficiency and in the specific work output. Comparison of a ‘rubber’ and ‘non-rubber’ gas turbine confirmed that residence time is one important factor in NOx formation.

Application of “H Gas Turbine” Design Technology to Increase Thermal Efficiency and Output Capability of the Mitsubishi M701G2 Gas Turbine

2005 ◽  
Vol 127 (2) ◽  
pp. 369-374 ◽  
Author(s):  
Y. Fukuizumi ◽  
J. Masada ◽  
V. Kallianpur ◽  
Y. Iwasaki
Keyword(s):  
Gas Turbine ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Turbine Blades ◽  
Combined Cycle ◽  
Load Test ◽  
Air Cooling ◽  
Load Testing ◽  
Design Development

Mitsubishi completed design development and verification load testing of a steam-cooled M501H gas turbine at a combined cycle power plant at Takasago, Japan in 2001. Several advanced technologies were specifically developed in addition to the steam-cooled components consisting of the combustor, turbine blades, vanes, and the rotor. Some of the other key technologies consisted of an advanced compressor with a pressure ratio of 25:1, active clearance control, and advanced seal technology. Prior to the M501H, Mitsubishi introduced cooling-steam in “G series” gas turbines in 1997 to cool combustor liners. Recently, some of the advanced design technologies from the M501H gas turbine were applied to the G series gas turbine resulting in significant improvement in output and thermal efficiency. A noteworthy aspect of the technology transfer is that the upgraded G series M701G2 gas turbine has an almost equivalent output and thermal efficiency as H class gas turbines while continuing to rely on conventional air cooling of turbine blades and vanes, and time-proven materials from industrial gas turbine experience. In this paper we describe the key design features of the M701G2 gas turbine that make this possible such as the advanced 21:1 compressor with 14 stages, an advanced premix DLN combustor, etc., as well as shop load test results that were completed in 2002 at Mitsubishi’s in-house facility.

scholarly journals Influences of Pressure ratio and Fluid Temperature on overall Cooling Performances of Ribbed Channel with Film Holes

2021 ◽  
Vol 2087 (1) ◽  
pp. 012043
Author(s):  
Yi Li ◽  
Jianhua Wang ◽  
Xu Wang ◽  
Weilong Wu ◽  
Hang Su
Keyword(s):  
Numerical Simulations ◽  
Pressure Ratio ◽  
Fluid Temperature ◽  
Temperature Ratio ◽  
Cooling Effectiveness ◽  
Real Gas ◽  
Outlet Pressure ◽  
Ribbed Channel ◽  
Similar Temperature ◽  
Cooling Air

Abstract The previous experiments of overall cooling performances were most conducted using simplified models and under the similar temperature ratio of mainstream to cooling air with real gas turbine operations, and ambient outlet pressure. To discuss the reliability of this type of experimental data, this paper exhibits two series of numerical simulations. Using a real E3 blade as model, which has two-pass rib-roughened channel with inclined film holes, numerical simulations are carried out at the same temperature ratio and pressure ratio, but different fluid temperatures including mainstream and cooling air, and different outlet pressure. The numerical results reveal two important conclusions: 1) At the same outlet pressure, the overall cooling effectiveness on PS is not sensitive to the fluid temperatures, but on SS in the region between two rows of film holes, a higher fluid temperature corresponds to a higher cooling effectiveness. 2) At the same pressure ratio of inlet to outlet, the overall cooling effectiveness on PS and SS is not sensitive to the outlet pressure and fluid temperature.

scholarly journals Development of a Flexible Turbine Cooling Prediction Tool for Preliminary Design of Gas Turbines

2018 ◽  
Vol 140 (9) ◽  
Author(s):  
Feijia Yin ◽  
Floris S. Tiemstra ◽  
Arvind G. Rao
Keyword(s):  
Gas Turbines ◽  
Pressure Ratio ◽  
Engine Performance ◽  
Thermodynamic Cycle ◽  
Specific Power ◽  
Inlet Temperature ◽  
Turbine Cooling ◽  
Engine Efficiency ◽  
Semi Empirical ◽  
Cooling Air

As the overall pressure ratio (OPR) and turbine inlet temperature (TIT) of modern gas turbines are constantly being increased in the pursuit of increasing efficiency and specific power, the effect of bleed cooling air on the engine performance is increasingly becoming important. During the thermodynamic cycle analysis and optimization phase, the cooling bleed air requirement is either neglected or is modeled by simplified correlations, which can lead to erroneous results. In this current research, a physics-based turbine cooling prediction model, based on semi-empirical correlations for heat transfer and pressure drop, is developed and verified with turbine cooling data available in the open literature. Based on the validated model, a parametric analysis is performed to understand the variation of turbine cooling requirement with variation in TIT and OPR of future advanced engine cycles. It is found that the existing method of calculating turbine cooling air mass flow with simplified correlation underpredicts the amount of turbine cooling air for higher OPR and TIT, thus overpredicting the estimated engine efficiency.

Sign in / Sign up

Export Citation Format

Share Document