Advanced Gas Turbine and High Performance Gas-Steam Combined Cycle Plant With Blade Cooling Air Controlling

2006 ◽  
Author(s):  
Tadashi Tsuji
Keyword(s):  
Power Generation ◽  
Heat Exchanger ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Hot Water ◽  
Blade Cooling ◽  
Combined Cycle Plant ◽  
Cooling Air

Air cooling blades are usually applied to gas turbines as a basic specification. This blade cooling air is almost 20% of compressor suction air and it means that a great deal of compression load is not converted effectively to turbine power generation. This paper proposes the CCM (Cascade Cooling Module) system of turbine blade air line and the consequent improvement of power generation, which is achieved by the reduction of cooling air consumption with effective use of recovered heat. With this technology, current gas turbines (TIT: turbine inlet temperature: 1350°C) can be up-rated to have a relative high efficiency increase. The increase ratio has a potential to be equivalent to that of 1500°C Class GT/CC against 1350°C Class. The CCM system is designed to enable the reduction of blade cooling air consumption by the low air temperature of 15°C instead of the usual 200–400°C. It causes the turbine operating air to increase at the constant suction air condition, which results in the enhancement of power and thermal efficiency. The CCM is installed in the cooling air line and is composed of three stage coolers: steam generator/fuel preheater stage, heat exchanger stage for hot water supplying and cooler stage with chilled water. The coolant (chilled water) for downstream cooler is produced by an absorption refrigerator operated by the hot water of the upstream heat exchanger. The proposed CCM system requires the modification of cooling air flow network in the gas turbine but produces the direct effect on performance enhancement. When the CCM system is applied to a 700MW Class CC (Combined Cycle) plant (GT TIT: 135°C Class), it is expected that there will be a 40–80MW increase in power and +2–5% relative increase in thermal efficiency.

Gas Turbine Systems Designed for Coal Water Slurries

1984 ◽  
Author(s):  
A. J. Giramonti ◽  
F. L. Robson
Keyword(s):  
Power Generation ◽  
Corrosion Resistance ◽  
Power Systems ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Ceramic Coatings ◽  
Combined Cycle ◽  
Coal Powder ◽  
Combined Cycle Plant ◽  
Power Generation Systems

Numerous attempts have been made during the past two decades to develop advanced power generation systems which could burn coal or coal-derived fuels both economically and in an environmentally acceptable manner. Although much valuable technology has been derived from these programs, commercially viable power generation alternatives have not yet appeared. One prospective way to expedite the commercialization of advanced coal-fired power systems is to meld the latest gas turbine technology with the emerging technology for producing slurries of water and ultra clean coal. This paper describes a DOE-sponsored program to identify the most attractive gas turbine power system that can operate on slurry fuels. The approach is to use slurries produced from finely ground (<10 microns) coal powder from which most of the ash and sulfur has been removed. The gas turbines will incorporate a rich-burn, quick-quench combustor to minimize conversion of fuel-bound nitrogen to NOx, advanced single crystal alloys with improved hot corrosion resistance and strength, advanced metallic and ceramic coatings with improved erosion and corrosion resistance, and more effective hot section cooling. Two different power plant configurations are covered: a large (nominally 400 MW) combined cycle plant designed for base load applications; and a small (nominally 12 MW) simple-cycle plant designed for peaking, industrial, and cogeneration applications.

Cycle Optimization and High Performance Analysis of Gas Engine-Gas Turbine Combined Cycles

2005 ◽  
Author(s):  
Tadashi Tsuji
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Compound System ◽  
Generation Efficiency ◽  
Engine Exhaust ◽  
Gas Engine ◽  
Exhaust Temperature

The reciprocating engine operates with a maximum pressure and temperature in its cylinders that is higher than that in conventional gas turbines. When a gas engine is integrated with a gas turbine instead of a turbocharger, it is an ETCS (Engine-Turbo Compound System). We have developed the concept of a compound system with ERGT (Engine Reheat Gas Turbine) and propose it as a system with potentially high thermal efficiency. A natural gas firing gas turbine combined cycle (CC) is selected as the standard system for a thermal power plant. A higher TIT (Turbine Inlet Temperature) of gas turbine usually enables higher power generation efficiency. Focusing on the effect of engine exhaust temperature, we found that the ETCS cycle with a ERGT has the potential to achieve higher thermal efficiency than that of a gas turbine combined cycle, with no change in TIT. An engine exhaust temperature of 1173K increases the system power generation efficiency from 46 to 50%LHV (TIT 1150°C) and 54 to 57%LHV (TIT 1350°C), respectively. The gas engine–gas turbine combined cycle has the potential to achieve a significant efficiency increase of +4.1%LHV (TIT 1150°C) and +2.8%LHV (TIT 1350°C), making it a promising system for future power plants. Efficiency is expected to be improved by +8.7% (TIT 1150°C) and +5.6% (TIT 1350°C), relatively.

A Study of Cycle Performance of Ceramic Gas Turbines

1997 ◽  
Author(s):  
H. Sugishita ◽  
H. Mori ◽  
R. Chikami ◽  
Y. Tsukuda ◽  
S. Yoshino ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Performance Improvement ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Cycle Performance ◽  
Gas Temperature ◽  
Blade Cooling ◽  
Combined Cycles ◽  
Cooling Air

A study has been carried out to assess the performance improvement of a combined cycle used for an industrial power plant when ceramic turbine components are employed. This paper presents the details of this study. Performance improvement is obtained as a result of reduced blade cooling air. In this study four different kinds of combined cycles were investigated and these are listed below: A. Combined cycle with a simple gas turbine. B. Combined cycle with an inter-cooled gas turbine. C. Combined cycle with a reheat gas turbine. D. Combined cycle with an inter-cooled reheat gas turbine. Results of this study indicate that the combined cycle with a simple gas turbine is the most practical of the four cycles studied with an efficiency of higher than 60%. The combined cycle with reheat gas turbine has the highest efficiency if a higher compressor exit air temperature and a high gas temperature (over 1000°C) to reheat the combustion system are used. A higher pressure ratio is required to optimize the cycle performance of the combined cycle with the ceramic turbine components than that with the metal turbine components because of reduced blade cooling air. To minimize leakage air for these higher pressure ratios, advanced seal technology should be applied to the gas turbines.

Performance Analysis of a Combined Cycle Power Plant Through Exergetic and Environmental Indices

2017 ◽  
Author(s):  
Edgar Vicente Torres González ◽  
Raúl Lugo Leyte ◽  
Martín Salazar Pereyra ◽  
Helen Denise Lugo Méndez ◽  
Miguel Toledo Velázquez ◽  
...  
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Environmental Indices ◽  
Combined Cycle Power Plant ◽  
Combustion Gases ◽  
Combined Cycle Plant ◽  
Exergetic Analysis ◽  
Gas Turbine Power Plant

In this paper is carried out a comparison between a gas turbine power plant and a combined cycle power plant through exergetic and environmental indices in order to determine performance and sustainability aspects of a gas turbine and combined cycle plant. First of all, an exergetic analysis of the gas turbine and the combined is carried out then the exergetic and environmental indices are calculated for the gas turbine (case A) and the combined cycle (case B). The exergetic indices are exergetic efficiency, waste exergy ratio, exergy destruction factor, recoverable exergy ratio, environmental effect factor and exergetic sustainability. Besides, the environmental indices are global warming, smog formation and acid rain indices. In the case A, the two gas turbines generate 278.4 MW; whereas 415.19 MW of electricity power is generated by the combined cycle (case B). The results show that exergetic sustainability index for cases A and B are 0.02888 and 0.1058 respectively. The steam turbine cycle improves the overall efficiency, as well as, the reviewed exergetic indexes. Besides, the environmental indices of the gas turbines (case A) are lower than the combined cycle environmental indices (case B), since the combustion gases are only generated in the combustion chamber.

scholarly journals Development of a Low-NOx LBG Combustor for Coal Gasification Combined Cycle Power Generation Systems

1989 ◽  
Author(s):  
M. Sato ◽  
T. Abe ◽  
T. Ninomiya ◽  
T. Nakata ◽  
T. Yoshine ◽  
...  
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Coal Gasification ◽  
Combined Cycle ◽  
Generation System ◽  
Combustion Technology ◽  
Power Generation System ◽  
Combustion Tests ◽  
Power Generation Systems

From the view point of future coal utilization technology for the thermal power generation systems, the coal gasification combined cycle system has drawn special interest recently. In the coal gasification combined cycle power generation system, it is necessary to develop a high temperature gas turbine combustor using a low-BTU gas (LBG) which has high thermal efficiency and low emissions. In Japan a development program of the coal gasification combined cycle power generation system has started in 1985 by the national government and Japanese electric companies. In this program, 1300°C class gas turbines will be developed. If the fuel gas cleaning system is a hot type, the coal gaseous fuel to be supplied to gas turbines will contain ammonia. Ammonia will be converted to nitric oxides in the combustion process in gas turbines. Therefore, low fuel-NOx combustion technology will be one of the most important research subjects. This paper describes low fuel-NOx combustion technology for 1300°C class gas turbine combustors using coal gaseous low-BTU fuel as well as combustion characteristics and carbon monoxide emission characteristics. Combustion tests were conducted using a full-scale combustor used for the 150 MW gas turbine at the atmospheric pressure. Furthermore, high pressure combustion tests were conducted using a half-scale combustor used for the 1 50 MW gas turbine.

Pulsed Impingement Turbine Cooling and its Effect on the Efficiency of Gas Turbines With Pressure Gain Combustion

2020 ◽  
Author(s):  
Nicolai Neumann ◽  
Dieter Peitsch ◽  
Arne Berthold ◽  
Frank Haucke ◽  
Panagiotis Stathopoulos
Keyword(s):  
Gas Turbine ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Turbine Blades ◽  
Impingement Cooling ◽  
Turbine Cooling ◽  
Pressure Gain Combustion ◽  
Cooling Air ◽  
Gas Turbine Cycle ◽  
Cycle Efficiency

Abstract Performance improvements of conventional gas turbines are becoming increasingly difficult and costly to achieve. Pressure Gain Combustion (PGC) has emerged as a promising technology in this respect, due to the higher thermal efficiency of the respective ideal gas turbine cycle. Previous cycle analyses considering turbine cooling methods have shown that the application of pressure gain combustion may require more turbine cooling air. This has a direct impact on the cycle efficiency and reduces the possible efficiency gain that can potentially be harvested from the new combustion technology. Novel cooling techniques could unlock an existing potential for a further increase in efficiency. Such a novel turbine cooling approach is the application of pulsed impingement jets inside the turbine blades. In the first part of this paper, results of pulsed impingement cooling experiments on a curved plate are presented. The potential of this novel cooling approach to increase the convective heat transfer in the inner side of turbine blades is quantified. The second part of this paper presents a gas turbine cycle analysis where the improved cooling approach is incorporated in the cooling air calculation. The effect of pulsed impingement cooling on the overall cycle efficiency is shown for both Joule and PGC cycles. In contrast to the authors’ anticipation, the results suggest that for relevant thermodynamic cycles pulsed impingement cooling increases the thermal efficiency of Joule cycles more significantly than it does in the case of PGC cycles. Thermal efficiency improvements of 1.0 p.p. for pure convective cooling and 0.5 p.p. for combined convective and film with TBC are observed for Joule cycles. But just up to 0.5 p.p. for pure convective cooling and 0.3 p.p. for combined convective and film cooling with TBC are recorded for PGC cycles.

Operation Experiences of Siemens IGCC Gas Turbines Using Gasification Products From Coal and Refinery Residues

2000 ◽  
Author(s):  
M. Huth ◽  
A. Heilos ◽  
G. Gaio ◽  
J. Karg
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Strong Impact ◽  
Coal Gas ◽  
Operation Conditions ◽  
Wide Range ◽  
Commercial Operation ◽  
Burner Design

The Integrated Gasification Combined Cycle concept is an emerging technology that enables an efficient and clean use of coal as well as residuals in power generation. After several years of development and demonstration operation, now the technology has reached the status for commercial operation. SIEMENS is engaged in 3 IGCC plants in Europe which are currently in operation. Each of these plants has specific characteristics leading to a wide range of experiences in development and operation of IGCC gas turbines fired with low to medium LHV syngases. The worlds first IGCC plant of commercial size at Buggenum/Netherlands (Demkolec) has already demonstrated that IGCC is a very efficient power generation technology for a great variety of coals and with a great potential for future commercial market penetration. The end of the demonstration period of the Buggenum IGCC plant and the start of its commercial operation has been dated on January 1, 1998. After optimisations during the demonstration period the gas turbine is running with good performance and high availability and has exceeded 18000 hours of operation on coal gas. The air-side fully integrated Buggenum plant, equipped with a Siemens V94.2 gas turbine, has been the first field test for the Siemens syngas combustion concept, which enables operation with very low NOx emission levels between 120–600 g/MWh NOx corresponding to 6–30 ppm(v) (15%O2) and less than 5 ppm(v) CO at baseload. During early commissioning the syngas nozzle has been recognised as the most important part with strong impact on combustion behaviour. Consequently the burner design has been adjusted to enable quick and easy changes of the important syngas nozzle. This design feature enables fast and efficient optimisations of the combustion performance and the possibility for easy adjustments to different syngases with a large variation in composition and LHV. During several test runs the gas turbine proved the required degree of flexibility and the capability to handle transient operation conditions during emergency cases. The fully air-side integrated IGCC plant at Puertollano/Spain (Elcogas), using the advanced Siemens V94.3 gas turbine (enhanced efficiency), is now running successfully on coal gas. The coal gas composition at this plant is similar to the Buggenum example. The emission performance is comparable to Buggenum with its very low emission levels. Currently the gas turbine is running for the requirements of final optimization runs of the gasifier unit. The third IGCC plant (ISAB) equipped with Siemens gas turbine technology is located at Priolo near Siracusa at Sicilly/Italy. Two Siemens V94.2K (modified compressor) gas turbines are part of this “air side non-integrated” IGCC plant. The feedstock of the gasification process is a refinery residue (asphalt). The LHV is almost twice compared to the Buggenum or Puertollano case. For operation with this gas, the coal gas burner design was adjusted and extensively tested. IGCC operation without air extraction has been made possible by modifying the compressor, giving enhanced surge margins. Commissioning on syngas for the first of the two gas turbines started in mid of August 1999 and was almost finished at the end of August 1999. The second machine followed at the end of October 1999. Since this both machines are released for operation on syngas up to baseload.

300 MW Combined-Cycle Plant With Integrated Coal Gasification

1984 ◽  
Author(s):  
Rolf H. Kehlhofer
Keyword(s):  
Power Generation ◽  
Power Plant ◽  
Gas Turbines ◽  
Power Plants ◽  
Coal Gasification ◽  
District Heating ◽  
Combined Cycle ◽  
Liquid Fuels ◽  
Combined Cycle Plant ◽  
The Individual

In the past 15 years the combined-cycle (gas/steam turbine) power plant has come into its own in the power generation market. Today, approximately 30 000 MW of power are already installed or being built as combined-cycle units. Combined-cycle plants are therefore a proven technology, showing not only impressive thermal efficiency ratings of up to 50 percent in theory, but also proving them in practice and everyday operation (1) (2). Combined-cycle installations can be used for many purposes. They range from power plants for power generation only, to cogeneration plants for district heating or combined cycles with maximum additional firing (3). The main obstacle to further expansion of the combined cycle principle is its lack of fuel flexibility. To this day, gas turbines are still limited to gaseous or liquid fuels. This paper shows a viable way to add a cheap solid fuel, coal, to the list. The plant system in question is a 2 × 150 MW combined-cycle plant of BBC Brown Boveri with integrated coal gasification plant of British Gas/Lurgi. The main point of interest is that all the individual components of the power plant described in this paper have proven their worth commercially. It is therefore not a pilot plant but a viable commercial proposition.

Proposal of Innovative Gas Turbine Combined Cycle Power Generation System

2004 ◽  
Author(s):  
Hideto Moritsuka
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Generation System ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet ◽  
Power Generation System

In order to estimate the possibility to improve thermal efficiency of power generation use gas turbine combined cycle power generation system, benefits of employing the advanced gas turbine technologies proposed here have been made clear based on the recently developed 1500C-class steam cooling gas turbine and 1300C-class reheat cycle gas turbine combined cycle power generation systems. In addition, methane reforming cooling method and NO reducing catalytic reheater are proposed. Based on these findings, the Maximized efficiency Optimized Reheat cycle Innovative Gas Turbine Combined cycle (MORITC) Power Generation System with the most effective combination of advanced technologies and the new devices have been proposed. In case of the proposed reheat cycle gas turbine with pressure ratio being 55, the high pressure turbine inlet temperature being 1700C, the low pressure turbine inlet temperature being 800C, combined with the ultra super critical pressure, double reheat type heat recovery Rankine cycle, the thermal efficiency of combined cycle are expected approximately 66.7% (LHV, generator end).

Sign in / Sign up

Export Citation Format

Share Document