Some Implications of Noncoaxiality in Finite Deformations

1973 ◽  
Vol 95 (2) ◽  
pp. 87-93
Author(s):  
T. C. Hsu

Two-dimensional finite deformations are analyzed by factoring and multiplying the matrices of the linear transformations representing them. A general linear transformation consists of a pure shear, a uniform dilation, and a rigid-body rotation. Coaxiality is defined for finite deformations and its effect on the resultant distortion discussed. Tests for coaxiality are devised for use on rectangular grids which are often employed in metal forming research. Formulas are derived for the initial and final directions of the resultant major principal axis in both equal and unequal noncoaxial pure shears and, in particular, conditions are found for the constancy of distortion in the second deformation.

1971 ◽  
Vol 10 (58) ◽  
pp. 31-37 ◽  
Author(s):  
J. Weertman

AbstractThe value of the basal shear stress is derived for two-dimensional and three-dimensional cirque glaciers. It is assumed that a cirque glacier moves primarily by a rigid-body rotation over a bed of cylindrical or spherical shape. In the region of maximum ice thickness the new value of the basal shear stress is only about one half that derived from equations in common use in the literature. The new expression for the basal shear stress of a cirque glacier is used to correct a data point in Paterson’s recent compilation of measured sliding velocities and basal shear stresses of glaciers.


1971 ◽  
Vol 10 (58) ◽  
pp. 31-37 ◽  
Author(s):  
J. Weertman

The value of the basal shear stress is derived for two-dimensional and three-dimensional cirque glaciers. It is assumed that a cirque glacier moves primarily by a rigid-body rotation over a bed of cylindrical or spherical shape. In the region of maximum ice thickness the new value of the basal shear stress is only about one half that derived from equations in common use in the literature. The new expression for the basal shear stress of a cirque glacier is used to correct a data point in Paterson’s recent compilation of measured sliding velocities and basal shear stresses of glaciers.


Biology ◽  
2021 ◽  
Vol 10 (1) ◽  
pp. 45
Author(s):  
Fanwen Meng ◽  
Jacqueline Jonklaas ◽  
Melvin Khee-Shing Leow

Clinicians often encounter thyroid function tests (TFT) comprising serum/plasma free thyroxine (FT4) and thyroid stimulating hormone (TSH) measured using different assay platforms during the course of follow-up evaluations which complicates reliable comparison and interpretation of TFT changes. Although interconversion between concentration units is straightforward, the validity of interconversion of FT4/TSH values from one assay platform to another with different reference intervals remains questionable. This study aims to establish an accurate and reliable methodology of interconverting FT4 by any laboratory to an equivalent FT4 value scaled to a reference range of interest via linear transformation methods. As a proof-of-concept, FT4 was simultaneously assayed by direct analog immunoassay, tandem mass spectrometry and equilibrium dialysis. Both linear and piecewise linear transformations proved relatively accurate for FT4 inter-scale conversion. Linear transformation performs better when FT4 are converted from a more accurate to a less accurate assay platform. The converse is true, whereby piecewise linear transformation is superior to linear transformation when converting values from a less accurate method to a more robust assay platform. Such transformations can potentially apply to other biochemical analytes scale conversions, including TSH. This aids interpretation of TFT trends while monitoring the treatment of patients with thyroid disorders.


2021 ◽  
pp. 464-469
Author(s):  
Dominik Péus ◽  
Dominik Straumann ◽  
Alexander Huber ◽  
Christopher J. Bockisch ◽  
Vincent Wettstein

Downbeat nystagmus (DBN) observed in head-hanging positions, may be of central or peripheral origin. Central DBN in head-hanging positions is mostly due to a disorder of the vestibulo-cerebellum, whereas peripheral DBN is usually attributed to canalolithiasis of an anterior semicircular canal. Here, we describe an atypical case of a patient who, after head trauma, experienced severe and stereotypic vertigo attacks after being placed in various head-hanging positions. Vertigo lasted 10–15 s and was always associated with a robust DBN. The provocation of transient vertigo and DBN, which both showed no decrease upon repetition of maneuvers, depended on the yaw orientation relative to the trunk and the angle of backward pitch. On a motorized, multi-axis turntable, we identified the two-dimensional Helmholtz coordinates of head positions at which vertigo and DBN occurred (<i>y</i>-axis: horizontal, space-fixed; <i>z</i>-axis: vertical, and head-fixed; <i>x</i>-axis: torsional, head-fixed, and unchanged). This two-dimensional area of DBN-associated head positions did not change when whole-body rotations took different paths (e.g., by forwarding pitch) or were executed with different velocities. Moreover, the intensity of DBN was also independent of whole-body rotation paths and velocities. So far, therapeutic approaches with repeated liberation maneuvers and cranial vibrations were not successful. We speculate that vertigo and DBN in this patient are due to macular damage, possibly an unstable otolithic membrane that, in specific orientations relative to gravity, slips into a position causing paroxysmal stimulation or inhibition of macular hair cells.


2011 ◽  
Vol 24 (5) ◽  
pp. 548-555 ◽  
Author(s):  
Bas M. van Dalen ◽  
Kadir Caliskan ◽  
Osama I.I. Soliman ◽  
Floris Kauer ◽  
Heleen B. van der Zwaan ◽  
...  

Author(s):  
S Choura

The reduction of residual vibrations for the position control of a flexible rotating beam carrying a payload mass is investigated. The common practice used to find the position control of a flexible multi-link arm is to assign a torque actuator to each joint while the payload mass is kept fixed relative to the end-link during the time of manoeuvre. This paper examines the stability of the system if either the payload is freed accidentally to move along the beam during the time of manoeuvre or is allowed to span the beam in a desired path for control purposes. A candidate Lyapunov function is constructed and its time rate of change is examined. It is shown that the use of a PD (proportional plus derivative) torque control yields a convergence of residual vibration to zero, an attainment of the rigid-body rotation to a prespecified desired angle of manoeuvre and a constant velocity of the payload mass as it moves relative to the beam. For manipulation purposes, an additional control force is added to the moving actuator in order to regulate its axial motion. It is shown that allowing the axial motion of the payload mass in a prescribed manner leads to a considerable reduction of its residual vibrations as compared to the case where the payload mass is fixed to the beam tip during the time of manoeuvre. Stability is also verified through simulations of rigid-body rotation and payload axial motion track prespecified reference trajectories.


VLSI Design ◽  
1998 ◽  
Vol 6 (1-4) ◽  
pp. 91-95 ◽  
Author(s):  
A. Asenov ◽  
A. R. Brown ◽  
S. Roy ◽  
J. R. Barker

Topologically rectangular grids offer simplicity and efficiency in the design of parallel semiconductor device simulators tailored for mesh connected MIMD platforms. This paper presents several approaches to the generation of topologically rectangular 2D and 3D grids. The effects of the partitioning of such grids on different processor configurations are studied. A simulated annealing algorithm is used to optimise the partitioning of 2D and 3D grids on two dimensional arrays of processors. Problems related to the discretization, parallel matrix generation and solution strategy are discussed. The use of topologically rectangular grids is illustrated through the example of power electronic device simulation.


Author(s):  
Rémi Vachon ◽  
Mohsen Bazargan ◽  
Christoph F Hieronymus ◽  
Erika Ronchin ◽  
Bjarne Almqvist

Summary Elongate inclusions immersed in a viscous fluid generally rotate at a rate that is different from the local angular velocity of the flow. Often, a net alignment of the inclusions develops, and the resulting shape preferred orientation (SPO) of the particle ensemble can then be used as a strain marker that allows reconstruction of the fluid’s velocity field. Much of the previous work on the dynamics of flow-induced particle rotations has focused on spatially homogeneous flows with large-scale tectonic deformations as the main application. Recently, the theory has been extended to spatially varying flows, such as magma with embedded crystals moving through a volcanic plumbing system. Additionally, an evolution equation has been introduced for the probability density function (PDF) of crystal orientations. Here, we apply this new theory to a number of simple, two-dimensional flow geometries commonly encountered in magmatic intrusions, such as flow from a dyke into a reservoir or from a reservoir into a dyke, flow inside an inflating or deflating reservoir, flow in a dyke with a sharp bend, and thermal convection in a magma chamber. The main purpose is to provide a guide for interpreting field observations and for setting up more complex flow models with embedded crystals. As a general rule, we find that a larger aspect ratio of the embedded crystals causes a more coherent alignment of the crystals, while it has only a minor effect on the geometry of the alignment pattern. Due to various perturbations in the crystal rotation equations that are expected in natural systems, we show that the time-periodic behavior found in idealized systems is probably short-lived in nature, and the crystal alignment is well described by the time-averaged solution. We also confirm some earlier findings. For example, near channel walls, fluid flow often follows the bounding surface and the resulting simple shear flow causes preferred crystal orientations that are approximately parallel to the boundary. Where pure shear deformation dominates, there is a tendency for crystals to orient themselves in the direction of the greatest tensile strain rate. Where flow impinges on a boundary, for example in an inflating magma chamber or as part of a thermal convection pattern, the stretching component of pure shear aligns with the boundary, and the crystals orient themselves in that direction. In the field, this local pattern may be difficult to distinguish from a boundary-parallel simple shear flow. Pure shear also dominates along the walls of a deflating magma chamber and in places where the flow turns away from the reservoir walls, but in these locations, the preferred crystal orientation is perpendicular to the wall. Overall, we find that our calculated patterns of crystal orientations agree well with results from analogue experiments where similar geometries are available.


2012 ◽  
Vol 490-495 ◽  
pp. 2156-2159
Author(s):  
Wu Gang Li

In order to find the principal axes of inertia and calculate their moment of inertia to any plane homogeneous rigid body for calculating easily the moment of inertia to any axis of this rigid body, the principal axes could be found and their moment of inertia could be calculated automatically by using the reading-image of MATLAB to read the image messages about the flat surface of the rigid body and by the procedures which ware made according to the logic relation about the principal axis and the moment of inertia of the rigid body. Applying this method in a homogeneous cube, a result was acquired, error of which is small compared with the theoretical value. So this method is reliable, convenient and practical


Sign in / Sign up

Export Citation Format

Share Document