Assessment of URANS and DES for Prediction of Leading Edge Film Cooling

2011 ◽  
Vol 134 (3) ◽  
Author(s):  
Toshihiko Takahashi ◽  
Ken-ichi Funazaki ◽  
Hamidon Bin Salleh ◽  
Eiji Sakai ◽  
Kazunori Watanabe
Keyword(s):  
Turbulence Model ◽  
Film Cooling ◽  
Turbulence Modeling ◽  
Turbine Blades ◽  
Leading Edge ◽  
Vortex Structures ◽  
Temperature Fields ◽  
Detached Eddy Simulation ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness

This paper describes the assessment of CFD simulations for the film cooling on the blade leading edge with circular cooling holes in order to contribute durability assessment of the turbine blades. Unsteady RANS applying a k-ε-v2-f turbulence model and the Spalart and Allmaras turbulence model and detached-eddy simulation (DES) based on the Spalart and Allmaras turbulence model are addressed to solve thermal convection. The CFD calculations were conducted by simulating a semicircular model in the wind tunnel experiments. The DES and also the k-ε-v2-f model evaluate explicitly the unsteady fluctuation of local temperature by the vortex structures, so that the predicted film cooling effectiveness is comparatively in agreement with the measurements. On the other hand, the predicted temperature fields by the Spalart and Allmaras model are less diffusive than the DES and the k-ε-v2-f model. In the present turbulence modeling, the DES only predicts the penetration of main flow into the film cooling hole but the Spalart and Allmaras model is not able to evaluate the unsteadiness and the vortex structures clearly, and overpredict film cooling effectiveness on the partial surface.

Assessment of URANS and DES for Prediction of Leading Edge Film Cooling

2010 ◽  
Author(s):  
Toshihiko Takahashi ◽  
Ken-ich Funazaki ◽  
Hamidon Bin Salleh ◽  
Eiji Sakai ◽  
Kazunori Watanabe
Keyword(s):  
Turbulence Model ◽  
Film Cooling ◽  
Turbine Blades ◽  
Leading Edge ◽  
Vortex Structures ◽  
Temperature Fields ◽  
Detached Eddy Simulation ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Circular Model

This paper describes assessment of CFD simulations for the film-cooling on the blade leading edge with circular cooling holes in order to contribute durability assessment of the turbine blades. Unsteady RANS (URANS) applying a k–ε–v2–f turbulence model and the Spallart and Allmaras turbulence model, and Detached-Eddy Simulation (DES) based on the Spallart and Allmaras turbulence model are addressed to solve thermal convection. The CFD calculations were conducted by simulating a semi-circular model in the wind tunnel experiments. The DES and also the k–ε–v2–f model evaluate explicitly unsteady fluctuation of local temperature by the vortex structures, so that the predicted film cooling effectiveness comparatively in agreement with measurements. On the other hand, the predicted temperature fields by the Spallart and Allmaras model are less diffusive than the DES and the k–ε–v2–f model. In the present turbulence modeling, the DES only predicts penetration of main flow into the film cooling hole, but the Spallart and Allmaras model is not able to evaluate the unsteadiness and the vortex structures clearly, and over-predict film cooling effectiveness on the partial surface.

Experimental Study of Leakage Flow on Flow Field and Film Cooling of High Pressure Turbine Blade Platform

2015 ◽  
Author(s):  
Kenichiro Takeishi ◽  
Yutaka Oda ◽  
Shintaro Kozono
Keyword(s):  
High Pressure ◽  
Film Cooling ◽  
Turbine Blades ◽  
Leading Edge ◽  
Horseshoe Vortex ◽  
Temperature Fields ◽  
Leakage Flow ◽  
High Pressure Turbine ◽  
Film Cooling Effectiveness ◽  
Injection Angle

An experiment has been conducted to study stator/rotor disc cavity leakage flow on the platform of a highly loaded stationary linear blade cascade. The linear cascade consists of a scaled-up model of the high-pressure turbine blades of an E3 (Energy efficient engine) and leakage slot models installed under the platform. Experiments have been conducted to investigate the effect of the slot injection angle, leakage flow rates, distance between the leading edge of the blade and the slot, and spacing of the blades. The film-cooling effectiveness was measured by pressure sensitive paint (PSP), and the temperature fields and flow fields were investigated using laser-induced fluorescence (LIF) and particle image velocimetry (PIV), respectively. It was observed from the experiments that the leakage flow covered the surface of the blade platform when the distance between the leading edge and the slot was zero; however, with increasing distance, the horseshoe vortex dominates near the junction of the blade leading edge, and the leakage flow could not cover the region. It was also found that the leakage flow has an effect that promotes the formation of the horseshoe vortex for some experimental conditions.

Experimental Study of Oscillating Freestream Effect on the Spatiotemporal Distributions of Leading-Edge Film Cooling

2020 ◽  
Vol 143 (1) ◽  
Author(s):  
Hongyi Shao ◽  
Mohamed Qenawy ◽  
Tianlun Zhang ◽  
Di Peng ◽  
Yingzheng Liu ◽  
...  
Keyword(s):  
Experimental Study ◽  
Strouhal Number ◽  
Film Cooling ◽  
Turbine Blades ◽  
Leading Edge ◽  
Fast Response ◽  
Frame Rate ◽  
Cooling Effectiveness ◽  
Oscillation Effect ◽  
Film Cooling Effectiveness

Abstract An experimental study was conducted to investigate the influence of mainstream oscillations on spatio-temporal variation of leading-edge film cooling effectiveness. The investigation utilized fast-response pressure-sensitive paint (Fast-PSP) technique at high frame rate. During the experiment, coolant (i.e., CO2, DR = 1.53) was discharged into three rows of cylindrical holes. Various blowing ratios (i.e., M = 0.50, 0.75, 1.00, and 1.50) were tested under the steady (i.e., f = 0 Hz) and oscillating (i.e., f = 7 Hz and 25 Hz) conditions. The measured instantaneous effectiveness was analyzed in terms of time-averaged and phase-averaged results. The results revealed that the mainstream oscillation, consisting of simultaneous pressure and velocity oscillation, significantly influences the behavior of the film cooling effectiveness. The time-averaged effectiveness significantly decreased at high oscillating frequency (i.e., 13.0–19.8% reduction at M = 0.50, f = 25 Hz compared with f = 0 Hz), especially at low blowing ratios (i.e., M = 0.50 and 0.75). The phase-averaged results captured significant decay in the film distributions associated with backflow caused by negative pressure gradients in coolant holes at certain phases. However, the mainstream oscillation effect was relatively insignificant at high blowing ratios (i.e., M = 1.00 and 1.50), which revealed the robustness of coolant coverage at low coolant Strouhal number (i.e., high blowing ratio) under the same oscillating frequency. Furthermore, the unsteady coolant intermittency showed highly unstable film coverage at high coolant Strouhal number. The coolant decay associated with backflow at high coolant Strouhal number should be considered by the gas-turbine designers in order to improve the lifecycle of turbine blades.

scholarly journals Experimental Investigation of Disc Cavity Leakage Flow and Hub Endwall Contouring in a Linear Rotor Cascade

2011 ◽  
Author(s):  
Ryan D. Erickson ◽  
Terrence W. Simon ◽  
Luzeng Zhang ◽  
Hee-Koo Moon
Keyword(s):  
Thermal Performance ◽  
Film Cooling ◽  
Leading Edge ◽  
Turbine Rotor ◽  
Secondary Flows ◽  
Temperature Fields ◽  
Leakage Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Endwall Contouring

An experimental study is carried out in a stationary linear cascade which simulates a turbine rotor to compare the thermal performance of two new axisymmetric endwall contour geometries. Measurements of endwall adiabatic film cooling effectiveness and near-endwall passage temperature fields are made for this purpose. In addition to documenting endwall contouring effects, a range of disc cavity leakage flow rates is investigated. This information is meant to quantify, over the range tested, the benefits and penalties of introducing leakage flow into the passage using the designated endwall contouring. Special attention is paid to determine whether the endwall curvature has any effect on the interaction between mainstream and secondary flows within the passage. Results indicate improved thermal performance when strong endwall curvature exists near the blade leading edge. The strong curvature causes cavity leakage flow to remain closer to the endwall, thereby increasing cooling effectiveness.

Assessment of Steady State PSP and Transient Ir Measurement Techniques for Leading Edge Film Cooling

2005 ◽  
Author(s):  
Zhihong Gao ◽  
Lesley M. Wright ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Steady State ◽  
Film Cooling ◽  
Measurement Techniques ◽  
Turbine Blades ◽  
Leading Edge ◽  
Cooling Effectiveness ◽  
Stagnation Line ◽  
Film Cooling Effectiveness ◽  
Film Cooling Holes

Film cooling is commonly used on the leading edge of turbine blades to protect the blade surface from hot mainstream gases in the turbine. Obtaining detailed film cooling effectiveness distributions on the leading edge can be challenging. This paper considers two measurement techniques which can be applied to the leading edge (modeled by a cylinder) to obtain detailed distributions of the film effectiveness. A steady state pressure sensitive paint (PSP) technique and a transient infrared (IR) thermography technique are used to obtain detailed film cooling effectiveness distributions on the cylinder. The cylinder, 7.62 cm in diameter, is placed in a low speed wind tunnel, with the mainstream flow having a Reynolds number of 100,900 (based on the cylinder diameter). The cylinder has two rows of film cooling holes located at ±15° from the cylinder’s stagnation line. The pitch-to-diameter ratio of the film holes is 4, and holes are inclined 30° in spanwise direction. PSP continues to show promise for film cooling effectiveness measurements. Detailed distributions can be obtained near the film cooling holes because this technique relies on mass transfer rather than heat transfer. In order to reduce the error caused by conduction in heat transfer experiments, transient measurement techniques are favorable. Transient IR measurements are taken, and film cooling effectiveness is determined on the cylinder’s surface. Although the effect of conduction is reduced with the transient IR technique (compared to a steady state heat transfer experiment), heat conduction through the cylinder has not been eliminated (or even minimized). Without correction, the results obtained from transient heat transfer experiments must be used cautiously. For this reason, PSP is developing a niche within the gas turbine community for detailed film cooling effectiveness measurements.

Film Cooling Effectiveness From a Single Scaled-Up Fan-Shaped Hole: A CFD Simulation of Adiabatic and Conjugate Heat Transfer Models

2005 ◽  
Author(s):  
Mahmood Silieti ◽  
Alain J. Kassab ◽  
Eduardo Divo
Keyword(s):  
Heat Transfer ◽  
Turbulence Model ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Cfd Simulation ◽  
Temperature Fields ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
Transfer Models

This paper documents a computational investigation of the film cooling effectiveness of a 3-D gas turbine endwall with one fan-shaped cooling hole. The simulations were performed for adiabatic and conjugate heat transfer models. Turbulence closure was investigated using three different turbulence models; the realizable k-ε model, the SST k-ω model, as well as the v2–f turbulence model. Results were obtained for a blowing ratio of one, and a coolant-to-mainflow temperature ratio of 0.54. The simulations used a dense, high quality, O-type, hexahedral grid with three different schemes of meshing for the cooling hole: hexahedral-, hybrid-, and tetrahedral-topology grid. The computed flow/temperature fields are presented, in addition to local, two-dimensional distribution of film cooling effectiveness for the adiabatic and conjugate cases. Results are compared to experimental data in terms of centerline film cooling effectiveness downstream cooling-hole, the predictions with realizable k-ε turbulence model exhibited the best agreement especially in the region for (2 ≤ x/D ≤ 6). Also, the results show the effect of the conjugate heat transfer on the temperature (effectiveness) field in the film cooling hole region and, thus, the additional heating up of the cooling jet itself.

Comparison of RANS and Detached Eddy Simulation Modeling Against Measurements of Leading Edge Film Cooling on a First-Stage Vane

2017 ◽  
Vol 139 (5) ◽  
Author(s):  
S. Ravelli ◽  
G. Barigozzi
Keyword(s):  
Film Cooling ◽  
Leading Edge ◽  
Intensity Level ◽  
Edge Region ◽  
Detached Eddy Simulation ◽  
Cooling Effectiveness ◽  
Stagnation Line ◽  
Film Cooling Effectiveness ◽  
Eddy Simulation ◽  
Adiabatic Effectiveness

The performance of a showerhead arrangement of film cooling in the leading edge region of a first-stage nozzle guide vane was experimentally and numerically evaluated. A six-vane linear cascade was tested at an isentropic exit Mach number of Ma2s = 0.42, with a high inlet turbulence intensity level of 9%. The showerhead cooling scheme consists of four staggered rows of cylindrical holes evenly distributed around the stagnation line, angled at 45 deg toward the tip. The blowing ratios tested are BR = 2.0, 3.0, and 4.0. Adiabatic film cooling effectiveness distributions on the vane surface around the leading edge region were measured by means of thermochromic liquid crystals (TLC) technique. Since the experimental contours of adiabatic effectiveness showed that there is no periodicity across the span, the computational fluid dynamics (CFD) calculations were conducted by simulating the whole vane. Within the Reynolds-averaged Navier–Stokes (RANS) framework, the very widely used realizable k–ε (Rke) and the shear stress transport k–ω (SST) turbulence models were chosen for simulating the effect of the BR on the surface distribution of adiabatic effectiveness. The turbulence model which provided the most accurate steady prediction, i.e., Rke, was selected for running detached eddy simulation (DES) at the intermediate value of BR = 3. Fluctuations of the local temperature were computed by DES, due to the vortex structures within the shear layers between the main flow and the coolant jets. Moreover, mixing was enhanced both in the wall-normal and spanwise directions, compared to RANS modeling. DES roughly halved the prediction error of laterally averaged film cooling effectiveness on the suction side of the leading edge. However, neither DES nor RANS provided the expected decay of effectiveness progressing downstream along the pressure side, with 15% overestimation of ηav at s/C = 0.2.

Aerothermal Effect of Cavity Welding Beads on a Transonic Squealer Tip

2020 ◽  
Author(s):  
Joao Vieira ◽  
John Coull ◽  
Peter Ireland ◽  
Eduardo Romero
Keyword(s):  
High Pressure ◽  
Film Cooling ◽  
Turbine Blades ◽  
Reynolds Numbers ◽  
High Pressure Turbine ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Aerodynamic Loss ◽  
Blade Tip ◽  
Mass Flow Rates

Abstract High pressure turbine blade tips are critical for gas turbine performance and are sensitive to small geometric variations. For this reason, it is increasingly important for experiments and simulations to consider real geometry features. One commonly absent detail is the presence of welding beads on the cavity of the blade tip, which are an inherent by-product of the blade manufacturing process. This paper therefore investigates how such welds affect the Nusselt number, film cooling effectiveness and aerodynamic performance. Measurements are performed on a linear cascade of high pressure turbine blades at engine realistic Mach and Reynolds numbers. Two cooled blade tip geometries were tested: a baseline squealer geometry without welding beads, and a case with representative welding beads added to the tip cavity. Combinations of two tip gaps and several coolant mass flow rates were analysed. Pressure sensitive paint was used to measure the adiabatic film cooling effectiveness on the tip, which is supplemented by heat transfer coefficient measurements obtained via infrared thermography. Drawing from all of this data, it is shown that the weld beads have a generally detrimental impact on thermal performance, but with local variations. Aerodynamic loss measured downstream of the cascade is shown to be largely insensitive to the weld beads.

Sign in / Sign up

Export Citation Format

Share Document