Radiative-Collisional Models in Non-Equilibrium Aerothermodynamics of Entry Probes

2012 ◽  
Vol 134 (3) ◽  
Author(s):  
Sergey T. Surzhikov

To design space vehicles aimed for returning payloads from a geostationary orbit, the Moon and other large or small planets of Solar system, a knowledge of the total (convective and radiative) heating from an environment is required. It is well known that the radiative heat load on a space vehicle moving through the atmosphere increases as the speed and the size increase, therefore, in many of these missions the large part of the trajectory will pass at high altitude, where the low atmospheric density can lead to significant thermal, chemical and physical nonequilibrium effects. Physical models and computational codes used to predict the aerothermodynamics must account for not only high temperature equilibrium thermodynamics (as a rule, within the framework of the local thermodynamic equilibrium (LTE) approach), but also for nonequilibrium one. Therefore, an accurate prediction of radiative heating as well as convective one under both equilibrium and nonequilibrium conditions becomes important to designers and space mission planners. To develop a prediction computational fluid dynamics (CFD) tool for reentry flows, where dissociation, ionization and radiation are important, some major areas are addressed. The most significant of them are following: (1) physical-chemical kinetics of high temperature dissociated and ionized gases, (2) transport properties of the gas mixtures, (3) spectral radiation properties of high temperature gases and low-temperature plasmas, (4) numerical simulation algorithms for prediction of nonequilibrium gas mixtures dynamics and radiation heat transfer in volumes of various geometry, and (5) models of physical and chemical processes accompanied by interaction of gas flows and radiation with thermoprotection systems (TPS) of space vehicles (including their thermochemical destruction, ablation, sublimation, etc.). In literatures (See Refs. (Park, C, 1990, Nonequilibrium Hypersonic Aerothermodynamics, Willey-Interscience Publication, J. Wiley & Sons, New York; Park, C., 1993, “Review of Chemical Kinetic Problems of Future NASA Missions. I: Earth Entries,” J. Thermophys. Heat Transfer, 7(3), pp. 385–398; Park, et al., 1994, “Review of Chemical-Kinetic Problems of Future NASA Missions, II: Mars Entries,” J. Thermophys. Heat Transfer, 8(1), pp. 9–23; Sarma, G., 2000, “Physico-Chemical Modelling in Hypersonic Flow Simulation,” Prog. Aerosp. Sci., 36, pp. 281–349; Huo, and Thuemmel, 1995, Electron-Air Molecule Collisions in Hypersonic Flows. Molecular Physics and Hypersonic Flows, Capitelli M., ed., Kluwer Academic Publishers, pp. 115–138.)) one can find reviews of governing equations used in the aerophysics, boundary conditions and the associated inputs using the physical-chemical models and their partially successful applications. This article presents the states of the art of models of electronic kinetics in the nonequilibrium low-temperature plasma of complex chemical compositions (air and carbon dioxide mixtures) widely met in various aerospace applications. Special attention is given to electronic kinetics of atoms and diatomic molecules within the framework of the radiative-collisional models.

2007 ◽  
Vol 550 ◽  
pp. 381-386 ◽  
Author(s):  
B. Decreus ◽  
Hatem S. Zurob ◽  
John Dunlop ◽  
Yves Bréchet

The effect of low temperature recovery treatments on the recrystallization kinetics during subsequent high temperature annealing was investigated in three Al-2.5%Mg alloys with various Fe additions. Recovery treatments were carried out at 190oC for times ranging from 0.25 to 65 hrs. Recrystallization treatments were carried out at 280oC. The kinetics of recrystallization was followed using the techniques of hardness measurement, optical metallography and calorimetry.


2021 ◽  
Vol 10 (1) ◽  
pp. 24-35
Author(s):  
Andi Muhammad Irfan ◽  
Nunik Lestari ◽  
Arimansyah Arimansyah ◽  
A Ramli Rasyid

This study was aimed to determine the drying kinetics of chilies that have been pretreated with low temperature long time (LTLT) blanching. Drying chilies with LTLT blanching pretreatment at 60, 70, and 80 oC for 20 minutes was assigned as treatment in this research. Drying chillies with high temperature short time (HTST) blanching pretreatment, without blanching pretreatment in the dryer, and without blanching pretreatment in direct sunlight were also studied as the comparison. The results showed that chilies treated with blanching pretreatment, both LTLT and HTST, have a faster drying rate and achieve the target moisture content faster than chilies that were not blanched. The color of dried chilies that were dried in a dryer was also better than dried chilies that were dried in the sun. Of all the blanching treatments, chilies with LTLT blanching pretreatment at 80 oC for 20 minutes had the fastest drying rate, a drying time of 34 hours, and the attractive dried chilli color. The evaluation results also showed that the Page model was the most suitable model to describe the drying characteristics of chilies with LTLT pretreatment blanching, with R2 ranging from 0.9913-0.9935, X2 ranging from 0.0005-0.0009, and RSME ranging from 0.0221-0.0293. Keywords: Chili; blanching; color; drying; mathematical model   ABSTRAK Penelitian ini bertujuan untuk mengetahui kinetika pengeringan cabai yang diberi perlakuan awal low temperature long time (LTLT) blanching atau blansing pada suhu rendah dalam waktu yang relatif lama. Perlakuan pada penelitian ini yaitu pengeringan cabai dengan blansing metode LTLT pada suhu 60o, 70o, dan 80oC selama 20 menit. Sebagai pembanding, dilakukan juga pengeringan dengan perlakuan awal metode high temperature short time (HTST) blanching, pengeringan cabai tanpa perlakuan awal blansing di dalam alat pengering, serta pengeringan cabai tanpa perlakuan awal blansing di bawah sinar matahari secara langsung. Hasil penelitian menunjukkan bahwa cabai dengan perlakuan awal blansing, baik blansing metode LTLT maupun HTST, memiliki laju pengeringan yang lebih tinggi sehingga lebih cepat mencapai kadar air target dibandingkan dengan cabai tanpa perlakuan blansing. Warna cabai kering yang dihasilkan pada alat pengering juga lebih baik dari cabai kering yang dikeringkan langsung di bawah sinar matahari. Dari seluruh perlakuan yang melibatkan proses blansing, cabai dengan blansing metode LTLT pada suhu 80oC selama 20 menit merupakan perlakuan dengan laju pengeringan tercepat, dengan waktu pengeringan selama 34 jam, dan warna produk cabai kering yang menarik. Hasil evaluasi juga menunjukkan bahwa model Page adalah model yang paling sesuai untuk menggambarkan karakteristik pengeringan cabai dengan perlakuan awal blansing metode LTLT, dengan R2 berkisar antara 0.9913-0.9935, X2 berkisar antara 0.0005-0.0009, dan RSME berkisar antara 0.0221-0.0293. Kata kunci: Blansing; cabai; model matematika; pengeringan; warna


2020 ◽  
Vol 10 (17) ◽  
pp. 5890
Author(s):  
Jiyoung Yoon ◽  
Junkyu Park ◽  
Jinhyoung Park

When designing a hand caliber with a high-temperature, high-pressure internal fluid transport pipe, reliability, safe use, and performance must be considered. Reliability refers to the stress caused by thermo-mechanical load; safe use refers to the low-temperature burns that might occur upon contact, and high-temperature burns caused by gas leakage occurring in the cylinder gap; and performance refers to projectile velocity. In this study, numerical simulation methods for heat transfer, structure analysis, and gas leakage are proposed so that solutions can be designed to account for the above three criteria. Furthermore, a hand-caliber design guide is presented. For heat transfer and structural analysis, mesh size, the transient convective heat transfer coefficient, and boundary conditions are described. Regarding gas leakage, methods reflecting projectile motion and determination of the molecular weight of the propellant are described. As a result, a designed hand caliber will have a high reliability, because the thermo-mechanical stress is lower than the yield stress. There will be little risk of low-temperature burns, but there will be a high temperature-burn risk, owing to gas leakage in the cylinder gap. The larger the cylinder-gap size, the greater the gas leakage and the smaller projectile velocity. The presented numerical simulation method can be applied to evaluate various aspects of other structures that require high-temperature, high-pressure fluid-transport pipes.


1998 ◽  
Vol 552 ◽  
Author(s):  
D. C. Lu ◽  
T. M. Pollock

ABSTRACTThe kinetics of low temperature deformation were investigated in several different polycrystalline RuAl alloys with the use of strain rate change experiments at 77 K and 298 K. Compositions investigated include RuAl, RuAl+0.5%B, Ru51.5 A48.5, Ru52 Al48, RU53 A147+0.5%B, Ru54.5 Al45.5, and Ru52 Al43 Sc5. Flow stresses did not vary substantially with temperature between 77 K and 298 K. Rate sensitivities were low compared to other B2 compounds and similar in all compositions investigated. Analyses of dislocation substructures after low strain deformation were conducted. The deformation kinetics and substructural observations suggest a higher intrinsic deformability for RuAI alloys with respect to the other high temperature B2 aluminides.


1998 ◽  
Vol 513 ◽  
Author(s):  
S. E. Guthrie ◽  
G. J. Thomas ◽  
D. Noreus ◽  
E. Ronnebro

ABSTRACTIt has been established that Mg2NiH4 undergoes a phase change around 500°K in which the orientation of the NiH4 complex is quenched in a monoclinic distortion of the cubic high temperature phase. This results in the formation of domains in which the lattice distortion is accommodated by microtwinning. These effects can be absent when the hydride phase is formed below the transition temperature. Microscopic analysis verifies a similar basal cubic structure in the low temperature phase; however, the domains and microtwins are absent in this material and it can readily be destabilized by thermal stresses induced by the electron beam. It is of interest to measure and compare the effect of the lattice differences on the thermodynamic properties of the low temperature versus the high temperature hydride phases. We report the equilibrium PCT data and hydrogen desorption kinetics of the two hydrides in the temperature range of 450–570 K.


Author(s):  
R. A. A. Abdul Husain ◽  
G. E. Andrews

Transient cooling techniques were developed for the direct simultaneous measurement of full coverage multi-jet impingement heat transfer coefficient and cooling effectiveness under high temperature combustion convective wall heating conditions. A step change in the impingement coolant flow rate was made and the change in temperature recorded as a function of time, from which the heat transfer coefficient was calculated. A comparison between steady state and transient techniques was also made on a conventional low temperature electrically heated test facility and good agreement was found. There was reasonable agreement between the high temperature heat transfer coefficients and the low temperature results, using similar transient cooling techniques. There was little influence of the coolant to wall temperature ratio on the impingement heat transfer coefficient or the cooling effectiveness obtained from the high temperature test rig. The transient technique was used to study the influence of crossflow in the impingement gap on both the cooling effectiveness and the heat transfer coefficient for a range of low pressure loss impingement walls with an X/D of 1.9–11.


Author(s):  
К.Н. Волков ◽  
В.Н. Емельянов ◽  
А.Г. Карпенко

Рассматриваются вопросы, связанные с численным моделированием газодинамических и физико-химических процессов, сопровождающих гиперзвуковое обтекание тел различной формы. Математическая модель включает в себя уравнения газовой динамики, записанные для реального газа, и уравнения химической кинетики, описывающие равновесные процессы в высокотемпературном воздухе. Для дискретизации основных расчетных соотношений применяется метод конечных объемов и различные разностные схемы для дискретизации конвективных потоков. Возможности разработанной вычислительной процедуры показываются на примере решения ряда задач физико-химической газовой динамики. Расчеты проводятся с использованием графических процессоров общего назначения. Обсуждается время счета, достигнутое при использовании различных разностных схем и подходов к описанию свойств высокотемпературного воздуха. Numerical simulation of gas dynamic and physical-chemical processes in hypersonic flows past bodies of various shapes is considered. The mathematical model includes the gas dynamics equations of real gases and the equations of chemical kinetics describing equilibrium processes in high-temperature air. The finite volume method and various finite difference schemes for the discretization of convective fluxes are used to discretize the governing equations. The capabilities of the numerical procedure are demonstrated by the solution of a number of problems in physical-chemical gas dynamics. The calculations are performed using general-purpose graphics processor units. The computational time achieved with the use of various finite difference schemes and the approaches to describe the properties of high-temperature air are discussed.


Sign in / Sign up

Export Citation Format

Share Document