Failure Diagnosis of a Gear Box by Recurrences

2012 ◽  
Vol 134 (4) ◽  
Author(s):  
Arkadiusz Syta ◽  
Józef Jonak ◽  
Łukasz Jedliński ◽  
Grzegorz Litak

The recurrence analysis method is used in the mechanical diagnosis of a gear transmission system using time domain data. The recurrence is a natural behavior of a periodic motion system, which tells the state of the system, after running some time, and will approach a certain past state. In this paper, some statistical parameters of recurrence qualification analysis are extensively evaluated for the use of mechanical diagnosis, based on fairly short acceleration time series; recurrence results are compared with those obtained from Fourier analysis, and the identification procedures for the failure gear transmission by recurrences is also presented. It is found that, using only fairly short time series, some statistical parameters in quantification recurrence analysis can give clear-cut distinction between a healthy and damaged state.

Author(s):  
Tie Liang ◽  
Qingyu Zhang ◽  
Xiaoguang Liu ◽  
Bin Dong ◽  
Xiuling Liu ◽  
...  

Abstract Background The key challenge to constructing functional corticomuscular coupling (FCMC) is to accurately identify the direction and strength of the information flow between scalp electroencephalography (EEG) and surface electromyography (SEMG). Traditional TE and TDMI methods have difficulty in identifying the information interaction for short time series as they tend to rely on long and stable data, so we propose a time-delayed maximal information coefficient (TDMIC) method. With this method, we aim to investigate the directional specificity of bidirectional total and nonlinear information flow on FCMC, and to explore the neural mechanisms underlying motor dysfunction in stroke patients. Methods We introduced a time-delayed parameter in the maximal information coefficient to capture the direction of information interaction between two time series. We employed the linear and non-linear system model based on short data to verify the validity of our algorithm. We then used the TDMIC method to study the characteristics of total and nonlinear information flow in FCMC during a dorsiflexion task for healthy controls and stroke patients. Results The simulation results showed that the TDMIC method can better detect the direction of information interaction compared with TE and TDMI methods. For healthy controls, the beta band (14–30 Hz) had higher information flow in FCMC than the gamma band (31–45 Hz). Furthermore, the beta-band total and nonlinear information flow in the descending direction (EEG to EMG) was significantly higher than that in the ascending direction (EMG to EEG), whereas in the gamma band the ascending direction had significantly higher information flow than the descending direction. Additionally, we found that the strong bidirectional information flow mainly acted on Cz, C3, CP3, P3 and CPz. Compared to controls, both the beta-and gamma-band bidirectional total and nonlinear information flows of the stroke group were significantly weaker. There is no significant difference in the direction of beta- and gamma-band information flow in stroke group. Conclusions The proposed method could effectively identify the information interaction between short time series. According to our experiment, the beta band mainly passes downward motor control information while the gamma band features upward sensory feedback information delivery. Our observation demonstrate that the center and contralateral sensorimotor cortex play a major role in lower limb motor control. The study further demonstrates that brain damage caused by stroke disrupts the bidirectional information interaction between cortex and effector muscles in the sensorimotor system, leading to motor dysfunction.


2021 ◽  
Vol 104 (3) ◽  
pp. 003685042110356
Author(s):  
Hexu Yang ◽  
Xiaopeng Li ◽  
Jinchi Xu ◽  
Zemin Yang ◽  
Renzhen Chen

According to the working characteristics of a 1.5 MW wind turbine planetary gear system under complex and random wind load, a two-parameter Weibull distribution model is used to describe the distribution of random wind speed, and the time-varying load caused by random wind speed is obtained. The nonlinear dynamic model of planetary gear transmission system is established by using the lumped parameter method, and the relative relations among various components are derived by using Lagrange method. Then, the relative relationship between the components is solved by Runge Kutta method. Considering the influence of random load and stiffness ratio on the planetary gear transmission system, the nonlinear dynamic response of cyclic load and random wind load on the transmission system is analyzed. The analysis results show that the variation of the stiffness ratio makes the planetary gear have abundant nonlinear dynamics behavior and the planetary gear can get rid of chaos and enter into stable periodic motion by changing the stiffness ratio properly on the premise of ensuring transmission efficiency. For the variable pitch wind turbine, the random change of external load increases the instability of the system.


2011 ◽  
Vol 65 ◽  
pp. 177-181
Author(s):  
Jia Hong Zheng ◽  
Min Li

The inherent characteristics of the wind generators growth gearbox were solved, then the reasons which caused the gear transmission system generating dynamic incentive was analyzed, and also internal incentive and external incentive were given to 2MW wind generators gear transmission system quantitatively. On the basis of these, 2MW wind generators growth gearbox system’s vibration response caused under internal incentive and external incentive was solved and analyzed.


2004 ◽  
Vol 471-472 ◽  
pp. 269-272
Author(s):  
Sheng Sheng Zhang ◽  
J.Z. Zheng ◽  
L. Cheng

Gear profile modification is an important method for reducing system vibration and noise of a gear transmission. In this paper, three kinds of gear profile modification curves are studied, and relevant experiments are conducted. Some useful conclusions based on the theoretical analysis and experimental results have been obtained. Line, parabola and sinusoid modification curves are very useful in improving the dynamic performance of a gear transmission system by reducing system vibration and noise. In order to design the optimal tooth profile modification curve, the curve type must be decided firstly according to the specific working condition, and the curve parameters can be determined by means of optimum programming.


Author(s):  
Christian Herff ◽  
Dean J. Krusienski

AbstractClinical data is often collected and processed as time series: a sequence of data indexed by successive time points. Such time series can be from sources that are sampled over short time intervals to represent continuous biophysical wave-(one word waveforms) forms such as the voltage measurements representing the electrocardiogram, to measurements that are sampled daily, weekly, yearly, etc. such as patient weight, blood triglyceride levels, etc. When analyzing clinical data or designing biomedical systems for measurements, interventions, or diagnostic aids, it is important to represent the information contained within such time series in a more compact or meaningful form (e.g., noise filtering), amenable to interpretation by a human or computer. This process is known as feature extraction. This chapter will discuss some fundamental techniques for extracting features from time series representing general forms of clinical data.


Author(s):  
Jingyue Wang ◽  
Haotian Wang ◽  
Lixin Guo

AbstractIn order to study the different backlash, gear damping ratio and random disturbance on dynamic behavior of gear transmission system, stochastic dynamic equations of the three-degree-of-freedom spur gear transmission system are established considering random disturbances of a low-frequency external excitation induced by torque fluctuation, gear damping ratio, gear backlash, excitation frequency and meshing stiffness. Using bifurcation diagram, phase diagram, time course diagram, Poincaré map and power spectrum of the system, the dynamic characteristics of the gear transmission system with different backlash under gear damping ratio changing, and the influence of the random disturbance of gear damping ratio on the bifurcation characteristic of system are analyzed. Numerical simulation shows that the gear transmission system will be from periodic motion with a noisy disturbance to chaotic-like motion by period-doubling bifurcation with decreasing gear damping ratio. In the small damping ratio range, the backlash has great effect on the motion characteristics. Random disturbance has an important effect on the bifurcation characteristics.


Sign in / Sign up

Export Citation Format

Share Document