Effects of a Low Octane Gasoline Blended Fuel on Negative Valve Overlap Enabled HCCI Load Limit, Combustion Phasing and Burn Duration

2013 ◽  
Vol 135 (7) ◽  
Author(s):  
Luke M. Hagen ◽  
Laura Manofsky Olesky ◽  
Stanislav V. Bohac ◽  
George Lavoie ◽  
Dennis Assanis
Keyword(s):  
Maximum Load ◽  
Heating Value ◽  
Hcci Combustion ◽  
Fuel Flow ◽  
Load Limit ◽  
Lower Heating Value ◽  
O2 Concentration ◽  
Negative Valve Overlap ◽  
Valve Overlap ◽  
Lower Heating

Homogeneous charge compression iginition (HCCI) combustion allows for the use of fuels with octane requirements below that of spark-ignited engines. A reference gasoline was compared with iso-octane and a low octane blend of gasoline and 40% n-heptane, NH40. Experiments were conducted on a single cylinder engine operating with negative valve overlap (NVO). The fuel flow rate per cycle was compensated based on the lower heating value to maintain a constant energy addition across fuels. Iso-octane and gasoline demonstrated similar maximum load, achieving a gross IMEPg of ~430 kPa, whereas the NH40 demonstrated an increased IMEPg of ~460 kPa. The NH40 could be operated at a later phasing compared with the higher octane fuels, and exhibited a shorter burn duration at a given fueling rate and phasing. These results could be due to compositional differences, as NH40 required less NVO compared to iso-octane and gasoline, leading to less thermal and compositional stratification, as well as a higher O2 concentration and less residual gas. Additionally, the NH40 fuel demonstrated a higher intermediate temperature heat release than the higher octane fuels, potentially contributing to the shorter burn duration. Overall, these results demonstrate clear benefits to NVO enabled HCCI combustion with low octane fuels.

Effects of a Low Octane Gasoline Blended Fuel on NVO Enabled HCCI Load Limit, Combustion Phasing and Burn Duration

2012 ◽  
Author(s):  
Luke M. Hagen ◽  
Laura Manofsky Olesky ◽  
Stanislav V. Bohac ◽  
George Lavoie ◽  
Dennis Assanis
Keyword(s):  
Maximum Load ◽  
Heating Value ◽  
Hcci Combustion ◽  
Fuel Flow ◽  
Load Limit ◽  
Lower Heating Value ◽  
O2 Concentration ◽  
Negative Valve Overlap ◽  
Valve Overlap ◽  
Lower Heating

Homogeneous Charge Compression Ignition (HCCI) combustion allows for the use of fuels with octane requirements below that of spark-ignited engines. A reference gasoline was compared with iso-octane and a low octane blend of gasoline and 40% n-heptane, NH40. Experiments were conducted on a single cylinder engine operating with negative valve overlap (NVO). The fuel flow rate per cycle was compensated based on the lower heating value to maintain a constant energy addition across fuels. Iso-octane and gasoline demonstrated similar maximum load, achieving a gross IMEPg of ∼430 kPa, whereas the NH40 demonstrated an increased IMEPg of ∼ 460kPa. The NH40 could be operated at a later phasing compared with the higher octane fuels, and exhibited a shorter burn duration at a given fueling rate and phasing. These results could be due to compositional differences, as NH40 required less NVO compared to iso-octane and gasoline, leading to less thermal and compositional stratification, as well as a higher O2 concentration and less residual gas. Additionally, the NH40 fuel demonstrated a higher intermediate temperature heat release than the higher octane fuels, potentially contributing to the shorter burn duration. Overall, these results demonstrate clear benefits to NVO enabled HCCI combustion with low octane fuels.

scholarly journals Comparative study of alternative biofuels on aircraft engine performance

2016 ◽  
Vol 231 (8) ◽  
pp. 1509-1521 ◽  
Author(s):  
Muhammad Hanafi Azami ◽  
Mark Savill
Keyword(s):  
Fuel Consumption ◽  
Engine Performance ◽  
Aircraft Engine ◽  
Specific Fuel Consumption ◽  
Energy Crisis ◽  
Mixing Ratio ◽  
Heating Value ◽  
Fuel Flow ◽  
Lower Heating Value ◽  
Lower Heating

Aviation industries are vulnerable to the energy crisis and simultaneously posed environmental concerns. Proposed engine technology advancements could reduce the environmental impact and energy consumption. Substituting the source of jet fuel from fossil-based fuel to biomass-based fuel will help reduce emissions and minimize the energy crisis. The present paper addresses the analysis of aircraft engine performance in terms of thrust, fuel flow and specific fuel consumption at different mixing ratio percentages (20%, 40%, 50%, 60% and 80%) of alternative biofuel blends already used in flight test (Algae biofuel, Camelina biofuel and Jatropha biofuel) at different flight conditions. In-house computer software codes, PYTHIA and TURBOMATCH, were used for the analysis and modeling of a three-shaft high-bypass-ratio engine which is similar to RB211-524. The engine model was verified and validated with open literature found in the test program of bio-synthetic paraffinic kerosene in commercial aircraft. The results indicated that lower heating value had a significant influence on thrust, fuel flow and specific fuel consumption at every flight condition and at all mixing ratio percentages. Wide lower heating value differences between two fuels give a large variation on the engine performances. Blended Kerosene–Jatropha biofuel and Kerosene–Camelina biofuel showed an improvement on gross thrust, net thrust, reduction of fuel flow and specific fuel consumption at every mixing ratio percentage and at different flight conditions. Moreover, the pure alternative of Jatropha biofuel and Camelina biofuel gave much better engine performances. This was not the case for the Kerosene–Algae blended biofuel. This study is a crucial step in understanding the influence of different blended alternative biofuels on the performance of aircraft engines.

scholarly journals Effects of Steam Injection and Stochiometry on Cyclone Gasification of Wood Powder

1996 ◽  
Author(s):  
Christian Fredriksson ◽  
Bengt Degerman ◽  
Björn Kjellström
Keyword(s):  
Theoretical Calculations ◽  
Steam Injection ◽  
Wood Powder ◽  
Heating Value ◽  
Fuel Flow ◽  
Lower Heating Value ◽  
Mass Flows ◽  
Equilibrium Calculations ◽  
Gasification Temperature ◽  
Lower Heating

Atmospheric gasification of wood powder in a cyclone has been studied. A cyclone gasifier has been designed where the wood powder is injected into the cyclone with air or air/steam as transport media. The effects of stochiometry and steam injection on the gasification temperature and gas composition are investigated. The experimental results are compared with theoretical equilibrium calculations. The fuel flow has been 26 kg/h corresponding to a thermal input of 140 kW. Equivalence ratio was varied between 0.15 and 0.4. Wood powder has been injected with steam mass flows of 50–80% of the fuel flow. The gas from the cyclone gasifier was analysed regarding CO, H2, CH4 and CO2. The lower heating value of the gas varies between 4 and 6 MJ/Nm3 with lower values for steam injected gasification. Compared to theoretical calculations the air/steam injected measurements showed better agreement with equilibrium predictions than only air injection.

scholarly journals Combustion Study of Polyoxymethylene Dimethyl Ethers and Diesel Blend Fuels on an Optical Engine

Energies ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4608
Author(s):  
Jingjing He ◽  
Hao Chen ◽  
Xin Su ◽  
Bin Xie ◽  
Quanwei Li
Keyword(s):  
Soot Formation ◽  
Comprehensive Evaluation ◽  
Chemical Properties ◽  
Heating Value ◽  
Optical Engine ◽  
Leading Role ◽  
Combustion Duration ◽  
Polyoxymethylene Dimethyl Ethers ◽  
Lower Heating Value ◽  
Lower Heating

Polyoxymethylene dimethyl ethers (PODE) are a newly appeared promising oxygenated alternative that can greatly reduce soot emissions of diesel engines. The combustion characteristics of the PODE and diesel blends (the blending ratios of PODE are 0%, 20%, 50% and 100% by volume, respectively) are investigated based on an optical engine under the injection timings of 6, 9, 12 and 15-degree crank angles before top dead center and injection pressures of 100 MPa, 120 MPa and 140 MPa in this study. The results show that both the ignition delay and combustion duration of the fuels decrease with the increasing of PODE ratio in the blends. However, in the case of the fuel supply of the optical engine being fixed, the heat release rate, cylinder pressure and temperature of the blend fuels decrease with the PODE addition due to the low lower heating value of PODE. The addition of PODE in diesel can significantly reduce the integrated natural flame luminosity and the soot formation under all injection conditions. When the proportion of the PODE addition is 50% and 100%, the chemical properties of the blends play a leading role in soot formation, while the change of the injection conditions have an inconspicuous effect on it. When the proportion of the PODE addition is 20%, the blend shows excellent characteristics in a comprehensive evaluation of combustion and soot reduction.

Biodiesel Effects on Influencing Parameters of Brake Fuel Conversion Efficiency in a Medium Duty Diesel Engine

2010 ◽  
Vol 132 (12) ◽  
Author(s):  
Joshua A. Bittle ◽  
Jesse K. Younger ◽  
Timothy J. Jacobs
Keyword(s):  
Conversion Efficiency ◽  
Energy Content ◽  
Combustion Efficiency ◽  
Operating Conditions ◽  
Biodiesel Fuel ◽  
Mass Energy ◽  
Fuel Conversion ◽  
Heating Value ◽  
Lower Heating Value ◽  
Lower Heating

Biodiesel remains an alternative fuel of interest for use in diesel engines. A common characteristic of biodiesel, relative to petroleum diesel, is a lowered heating value (or per mass energy content of the fuel). For same torque engine comparisons, the lower heating value translates into a higher brake specific fuel consumption (amount of fuel consumed per unit of power produced). The efficiency at which fuel energy converts into work energy, however, may remain unchanged. In this experimental study, evaluating nine unique engine operating conditions, the brake fuel conversion efficiency (an assessor of fuel energy to work energy efficiency) remains unchanged between 100% petroleum diesel fuel and 100% biodiesel fuel (palm olein) at all conditions, except for high load conditions. Several parameters may affect the brake fuel conversion efficiency, including heat loss, mixture properties, pumping work, friction, combustion efficiency, and combustion timing. This article describes a study that evaluates how the aforementioned parameters may change with the use of biodiesel and petroleum diesel, and how these parameters may result in differences in the brake fuel conversion efficiency.

scholarly journals Lower Heating Value of Jet Fuel from Hydrocarbon Class Concentration Data and Thermo-Chemical Reference Data: An Uncertainty Quantification

2021 ◽  
Author(s):  
Randall Boehm ◽  
Zhibin Yang ◽  
David Bell ◽  
John Feldhausen ◽  
Joshua Heyne
Keyword(s):  
Jet Fuel ◽  
Confidence Bands ◽  
Heats Of Formation ◽  
Concentration Data ◽  
Heating Value ◽  
Accuracy And Precision ◽  
Lower Heating Value ◽  
Detailed Assessment ◽  
Value Net ◽  
Lower Heating

A detailed assessment is presented on the calculation and uncertainty of the lower heating value (net heat of combustion) of conventional and sustainable aviation fuels, from hydrocarbon class concentration measurements, reference molecular heats of formation, and the uncertainties of these reference heats of formation. Calculations using this paper’s method and estimations using ASTM D3338 are reported for 17 fuels of diverse compositions and compared against reported ASTM D4809 measurements. All the calculations made by this method and the reported ASTM D4809 measurements agree (i.e., within 95% confidence intervals). The 95% confidence interval of the lower heating value of fuel candidates that are comprised entirely of normal- and iso-alkanes is less than 0.1 MJ/kg by the method described here, while high cyclo-alkane content leads to 95% confidence bands that approach 0.2 MJ/kg. Taking a possible bias into account, the accuracy and precision of the method described in this work could be as high as 0.23 MJ/kg for some samples.

scholarly journals The Technological Investigations Of Manufacturing Of Energy Chips

2015 ◽  
Vol 1 ◽  
pp. 220
Author(s):  
Ziedonis Miklašēvičs
Keyword(s):  
Moisture Content ◽  
Dry Mass ◽  
Quality Parameters ◽  
Heating Value ◽  
Long Term Storage ◽  
Lower Heating Value ◽  
Term Storage ◽  
Lower Heating

The methodology in Latvia forest industry provide to determine the quality of energy chips only in long- term storage places before selling. Due to the lack of hard empirical data about the quality parameters of energy chips in different phases of manufacturing process, this research paper consists of: - the identification and analyses of the factors that influenced the values of energy chips quality features such as: bulk density, moisture content, ash content, higher and lower heating value according to actual moisture content and per dry mass of the chips; - the methodology for determination the quality parameters of energy chips by analysis the wood moisture content and by choice the method of the manufacturing of energy chips.

scholarly journals EXERGY-BASED INVESTIGATION OF A COAL-FIRED ALLAM CYCLE

2019 ◽  
Vol 137 ◽  
pp. 01018 ◽  
Author(s):  
Jing Luo ◽  
Ogechi Emelogu ◽  
Tatiana Morosuk ◽  
George Tsatsaronis
Keyword(s):  
Fossil Fuels ◽  
Coal Gasification ◽  
High Efficiency ◽  
Cycle Performance ◽  
Energetic Efficiency ◽  
Component Level ◽  
Lower Efficiency ◽  
Heating Value ◽  
Lower Heating Value ◽  
Lower Heating

Allam cycle is a novel cycle that capitalizes on the unique thermodynamic properties of supercritical CO2 and the advantages of oxy-combustion for power generation. It is a high-pressure supercritical carbon dioxide cycle designed to combust fossil fuels such as natural gas or syngas (from coal gasification systems) with complete CO2 separation at a high-efficiency and zero atmospheric emissions. This semi-closed cycle produces sequestration-ready/pipeline quality CO2 by-product, and thus eliminates the need for additional CO2-capture system. The Coal-fueled Allam cycle is targeted to deliver between 51-52% net efficiency (lower heating value) for coal gasification. In this study, the expected energetic efficiency is verified by simulating the system in Ebsilon professional software and the result showed that the net efficiency of the simulated coal-fired plant is 30.7%, which is significantly lower than the targeted value. The lower efficiency maybe as a result of the missing heat integration in the system, the high power demand of the oxidant compressor and CO2 compressors. And an exergy analysis based on published cycle data is employed, to investigate the cycle performance, identify the sources of the cycle’s thermodynamic inefficiencies at the component level; a sensitivity analysis is also performed to study the effects of selected thermodynamic parameters on the overall performance of the coal-fired Allam cycle.

Industrial Process Description for the Recovery of Agricultural Water From Digestate

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
Halina Pawlak-Kruczek ◽  
Agnieszka Urbanowska ◽  
Weihong Yang ◽  
Gerrit Brem ◽  
Aneta Magdziarz ◽  
...  
Keyword(s):  
Anaerobic Digestion ◽  
Rural Areas ◽  
Reclaimed Water ◽  
Industrial Process ◽  
Hydrothermal Carbonization ◽  
Full Potential ◽  
Agricultural Water ◽  
Heating Value ◽  
Lower Heating Value ◽  
Lower Heating

Abstract Currently, the reclamation and reuse of water have not reached their full potential, although more energy is needed to obtain and transport freshwater and this solution has a more serious environmental impact. Agricultural irrigation is, by far, the largest application of reclaimed water worldwide, so the proposed concept may result in the production of water that can be used, among others, for crop irrigation. This paper describes a novel installation for the recovery of the agricultural water from the digestate, along with the results of initial experiments. Currently, water is wasted, due to evaporation, in anaerobic digestion plants, as the effluent from dewatering of the digestate is discharged into lagoons. Moreover, water that stays within the interstitial space of the digestate is lost in a similar fashion. With increasing scarcity of water in rural areas, such waste should not be neglected. The study indicates that hydrothermal carbonization (HTC) enhances mechanical dewatering of the agricultural digestate and approximately 900 L of water can be recovered from one ton. Dewatered hydrochars had a lower heating value of almost 10 MJ/kg, indicating the possibility of using it as a fuel for the process. The aim of this Design Innovation Paper is to outline the newly developed concept of an installation that could enable recovery of water from, so far, the neglected resource—i.e., digestate from anaerobic digestion plants.

The Ethanol-Water Humidification Process in EvGT Cycles

2004 ◽  
Author(s):  
Marcus Thern ◽  
Torbjo¨rn Lindquist ◽  
Tord Torisson
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Power Production ◽  
Test Facility ◽  
Level Energy ◽  
Water Mixture ◽  
Evaporation Process ◽  
Heating Value ◽  
Lower Heating Value ◽  
Lower Heating

Ethanol from bio-products has become an important fuel for future power production. However, the present production technology is rather expensive. This paper focuses on how to lower the production cost of ethanol extraction from mash, and to use the ethanol as a primary fuel in gas turbines for heat and power production. Today, ethanol is produced during distillation by supplying energy to extract the ethanol from the mash. Using the evaporation process in the evaporative gas turbine to extract the ethanol from the mash before the distillation step, a lot of energy can be saved. In the evaporation process, the ethanol is extracted directly from the mash using energy from low-level energy sources. The evaporation technology is therefore expected to reduce the cost for the ethanol production. Simultaneous heat and mass transfer inside the ethanol humidification tower drives a mixture of ethanol and water into the compressor discharge air. To investigate the evaporation of a binary mixture into air at elevated pressures and temperatures, a test facility was constructed and integrated into the evaporative gas turbine pilot-plant. The concentration of ethanol in the mash is not constant but depends on the sugar content in the feedstock used in the fermentation process. Tests were therefore conducted at different concentrations of ethanol in the ethanol-water mixture. Tests were also performed at different temperature and flow conditions to establish the influence of these parameters on the lower heating value of the produced low calorific gas. It has been shown that this technology extracts about 80% of the ethanol from the mash. It has also been shown that the composition of the resulting gas depends on the temperatures, flow rates and composition of the incoming streams. The tests have shown that the produced gas has a lower heating value between of 1.8 to 3.8 MJ/kg. The produced gas with heating values in the upper range is possible to use as fuel in the gas turbine without any pilot flame. Initial models of the ethanol humidification process have been established and the initial test results have been used for validating developed models.

Sign in / Sign up

Export Citation Format

Share Document