Experimental and Numerical Studies of Cavitation Effects in a Tapered Land Thrust Bearing

2014 ◽  
Vol 137 (1) ◽  
Author(s):  
Yin Song ◽  
Xiao Ren ◽  
Chun-wei Gu ◽  
Xue-song Li
Keyword(s):  
Reynolds Equation ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Pressure Profile ◽  
Navier Stokes ◽  
Negative Effects ◽  
Navier Stokes Equation ◽  
Thrust Bearings ◽  
Cavitation Phenomenon ◽  
Parametric Studies

In thrust bearings, cavitation may occur at high rotational speeds or low lubricant supply pressures, and it will influence the bearing performances. In this paper, a hydrodynamic tapered land thrust bearing has been studied both experimentally and numerically, with concentration on the cavitation phenomenon and its effects on the bearing performances. Evident cavitation regions have been observed in the experiments at higher rotational speeds. Traditional Reynolds equation and 3D Navier–Stokes equation (3D NSE) with a cavitation model have been used for numerical simulation, and the predicted results are examined against the experimental results. Compared with Reynolds equation, 3D NSE with Rayleigh–Plesset model provides better predictions of both oil–film pressure profile and cavitation area. Furthermore, the effects of the cavitation phenomenon on the thrust bearing performances are studied by parametric studies involving various rotational speeds and oil feeding pressures, using 3D NSE. It is found that the load capacity decreases at higher speeds because of enlargement of the cavitation area. And the negative effects of cavitation can be reduced at smaller film thickness and higher oil supply pressure. Conclusively, the above results show that the cavitation phenomenon has significant influences on the bearing performances at higher speeds, and 3D NSE provides an effective tool for analyzing the cavitation effects in thrust bearings.

On the Influence of Thrust Bearings on the Nonlinear Rotor Vibrations of Turbochargers

2016 ◽  
Author(s):  
Ioannis Chatzisavvas ◽  
Aydin Boyaci ◽  
Andreas Lehn ◽  
Marcel Mahner ◽  
Bernhard Schweizer ◽  
...  
Keyword(s):  
Hydrodynamic Model ◽  
Reynolds Equation ◽  
Energy Equation ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Oil Viscosity ◽  
Oil Film ◽  
Thrust Bearings ◽  
Run Up ◽  
Generalized Reynolds Equation

This work investigates the influence of hydrodynamic thrust bearings on the lateral rotor oscillations. Four thrust bearing models are compared in terms of their predictions of the oil-film pressure (Reynolds equation), the oil-film temperature (energy equation) and the load capacity. A detailed thrust bearing model using the generalized Reynolds equation and the 3D energy equation, a model using the standard Reynolds equation with a 2D energy equation, a model where the standard Reynolds equation and the 2D energy equation are decoupled and finally an isothermal thrust bearing model are presented. It is shown that in lower rotational speeds, the four models produce almost the same results. However, as the rotational speed is increased, the necessity for a thermo-hydrodynamic model is demonstrated. Run-up simulations of a turbocharger rotor/bearing system are performed, using an isothermal thrust bearing model with different inlet oil-temperatures. The influence of the oil-temperature of the thrust bearing on the subsynchronous rotor oscillations is investigated. Finally, a thermo-hydrodynamic model is compared with an isothermal in run-up simulations, where the influence of the variable oil-viscosity is discussed.

scholarly journals Run-Up Simulation of a Semi-Floating Ring Supported Turbocharger Rotor Considering Thrust Bearing and Mass-Conserving Cavitation

Lubricants ◽  
2021 ◽  
Vol 9 (4) ◽  
pp. 44
Author(s):  
Christian Ziese ◽  
Cornelius Irmscher ◽  
Steffen Nitzschke ◽  
Christian Daniel ◽  
Elmar Woschke
Keyword(s):  
Reynolds Equation ◽  
Energy Equation ◽  
Thrust Bearing ◽  
Three Dimensional ◽  
Reliable Prediction ◽  
Two Phase ◽  
Hydrodynamic Bearings ◽  
Thrust Bearings ◽  
Run Up ◽  
The Impact

The vibration behaviour of turbocharger rotors is influenced by the acting loads as well as by the type and arrangement of the hydrodynamic bearings and their operating condition. Due to the highly non-linear bearing behaviour, lubricant film-induced excitations can occur, which lead to sub-synchronous rotor vibrations. A significant impact on the oscillation behaviour is attributed to the pressure distribution in the hydrodynamic bearings, which is influenced by the thermo-hydrodynamic conditions and the occurrence of outgassing processes. This contribution investigates the vibration behaviour of a floating ring supported turbocharger rotor. For detailed modelling of the bearings, the Reynolds equation with mass-conserving cavitation, the three-dimensional energy equation and the heat conduction equation are solved. To examine the impact of outgassing processes and thrust bearing on the occurrence of sub-synchronous rotor vibrations separately, a variation of the bearing model is made. This includes run-up simulations considering or neglecting thrust bearings and two-phase flow in the lubrication gap. It is shown that, for a reliable prediction of sub-synchronous vibrations, both the modelling of outgassing processes in hydrodynamic bearings and the consideration of thrust bearing are necessary.

An Accurate Solution of the Gas Lubricated, Flat Sector Thrust Bearing

1977 ◽  
Vol 99 (1) ◽  
pp. 82-88 ◽  
Author(s):  
I. Etsion ◽  
D. P. Fleming
Keyword(s):  
Film Thickness ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Thickness Distribution ◽  
Maximum Load ◽  
Accurate Solution ◽  
Operating Conditions ◽  
Thrust Bearings ◽  
Practical Design ◽  
Minimum Film Thickness

A flat sector shaped pad geometry for gas lubricated thrust bearings is analyzed considering both pitch and roll angles of the pad and the true film thickness distribution. Maximum load capacity is achieved when the pad is tilted so as to create a uniform minimum film thickness along the pad trailing edge. Performance characteristics for various geometries and operating conditions of gas thrust bearings are presented in the form of design curves. A comparison is made with the rectangular slider approximation. It is found that this approximation is unsafe for practical design, since it always overestimates load capacity.

Static Characteristics of Gas Foil Thrust Bearing Based on Gas Rarefaction Model

2015 ◽  
Author(s):  
Jiajia Yan ◽  
Guanghui Zhang ◽  
Zhansheng Liu ◽  
Fan Yang
Keyword(s):  
Film Thickness ◽  
Optimization Design ◽  
Reynolds Equation ◽  
Thrust Bearing ◽  
Rarefied Gas ◽  
Load Capacity ◽  
Structural Parameters ◽  
Lubricating Film ◽  
Lift Off ◽  
Foil Thrust Bearing

A modified Reynolds equation for bump type gas foil thrust bearing was established with consideration of the gas rarefaction coefficient. Under rarefied gas lubrication, the Knudsen number which was affected by the film thickness and pressure was introduced to the Reynolds equation. The coupled modified Reynolds and lubricating film thickness equations were solved using Newton-Raphson Iterative Method and Finite Difference Method. By calculating the load capacity for increasing rotor speeds, the lift-off speed under certain static load was obtained. Parametric studies for a series of structural parameters and assembled clearances were carried out for bearing optimization design. The results indicate that with gas rarefaction effect, the axial load capacity would be decreased, and the lift-off speed would be improved. The rarefied gas has a more remarkable impact under a lower rotating speed and a smaller foil compliance coefficient. When the assembled clearance of the thrust bearing rotor system lies in a small value, the lift-off speed increases dramatically as the assembled clearance decreases further. Therefore, the axial clearance should be controlled carefully in assembling the foil thrust bearing. It’s worth noting that the linear uniform bump foil stiffness model is not exact for large foil compliance ∼0.5, especially for lift-off speed analysis, due to ignoring the interaction between bumps and bending stiffness of the foil.

Theoretical Study on Static Performance of Double-Bump Foil Bearings

2021 ◽  
Author(s):  
Fangcheng Xu ◽  
Jianhua Chu ◽  
Wenlin Luan ◽  
Guang Zhao
Keyword(s):  
Finite Element ◽  
Film Thickness ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Static Characteristics ◽  
Thrust Bearings ◽  
Foil Bearings ◽  
Foil Bearing ◽  
Static Performance ◽  
Initial Clearance

Abstract In this paper, single-bump foil models with different thickness and double-bump foil models with different initial clearances are established. The structural stiffness and equivalent viscous damping of double-bump foil and single-bump foil are analyzed by finite element simulation. The results show that the double-layer bump foil has variable stiffness and the displacement of the upper bump is greater than the initial gap when the two-layer bumps contact. A model for obtaining static characteristics of aerodynamic compliant foil thrust bearing is established on the basis of the stiffness characteristics of the double-bump foil. This paper solves gas Reynolds equation, the gas film thickness equation and the foil stiffness characteristic equation via the finite element method and the finite difference method. The static characteristics of the thrust bearings including the bearing pressure distribution, the gas film thickness and the friction power consumption have been obtained. The static characteristics of two kinds of foils have been compared and analyzed, and the effect of initial clearance on the static performance of double-bump foil bearings is studied. The results show that the double-bump foil structure can effectively improve the load capacity of thrust bearing. In addition, the static performance of double-bump foil thrust bearings is between the performance of the single-bump foil bearing and the double-bump foil bearing whose foil’s clearance is zero. The smaller the initial clearance is, the easier it will be to form a stable double-bump foil supporting structure.

Analytical Solution of Hydrostatic Pocket Tilting

2016 ◽  
Vol 821 ◽  
pp. 113-119 ◽  
Author(s):  
Eduard Stach ◽  
Jiří Falta ◽  
Matěj Sulitka
Keyword(s):  
Computational Models ◽  
Load Capacity ◽  
Navier Stokes ◽  
Navier Stokes Equation ◽  
Detailed Model ◽  
Limit Values ◽  
Inertia Effects ◽  
Proposed Model ◽  
Machine Tool Structure

Tilting (parallelism error) of guiding surfaces may cause reduction of load capacity of hydrostatic (HS) guideways and bearings in machine tools (MT). Using coupled finite element (FE) computational models of MT structures, it is nowadays possible to determine the extent of guiding surfaces deformation caused by thermal effects, gravitational force, cutting forces and inertia effects. Assessment of maximum allowable tilt has so far been based merely on experience. The paper presents a detailed model developed for description of the effect of HS bearing tilt on the load capacity characteristics of HS guideways. The model allows an evaluation of the tilt influence on the change of the characteristics as well as determination of the limit values of allowable tilt in interaction with compliant machine tool structure. The proposed model is based on the model of flow over the land of the HS pocket under extended Navier-Stokes equation. The model is verified using an experimental test rig.

Rayleigh Step Journal Bearing: Part 1—Compressible Fluid

1968 ◽  
Vol 90 (1) ◽  
pp. 271-280 ◽  
Author(s):  
B. J. Hamrock
Keyword(s):  
Compressible Fluid ◽  
Reynolds Equation ◽  
Journal Bearing ◽  
Load Capacity ◽  
Maximum Load ◽  
Pressure Profile ◽  
Clearance Ratio ◽  
Attitude Angle ◽  
Step Parameters ◽  
Bearing Part

A linearized PH solution to the Reynolds equation was obtained while neglecting side leakage. The analysis was divided into two parts—the step and ridge regions. The pressure profile across the step and ridge region of the various pads which are placed around the journal was obtained from the linearized PH Reynolds equation. Knowing the pressure, the load components and attitude angle were calculated. The resulting equations were found to be a function of the bearing parameters (the eccentricity and compressibility number) and the step parameters (ratio of the stepped clearance to the ridge clearance, ratio of the angle extended by the ridge to the angle extended by the pad, and number of pads placed around the journal). The maximum load capacity can be determined by numerically differentiating the load with respect to the step bearing parameters while finding where the slope is zero. A series of data was run while varying the bearing parameters. The attitude angle was calculated for the various cases which were run.

The Influence of Ambient Pressure on the Measured Load Capacity of Bump-Foil and Spiral-Groove Gas Thrust Bearings at Ambient Pressures up to 69 Bar on a Novel High-Pressure Gas Bearing Test Rig

2019 ◽  
Author(s):  
Jason Wilkes ◽  
Ryan Cater ◽  
Erik Swanson ◽  
Kevin Passmore ◽  
Jerry Brady
Keyword(s):  
Power Loss ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Ambient Pressure ◽  
Spiral Groove ◽  
Test Rig ◽  
Thrust Bearings ◽  
Order Of Magnitude ◽  
Foil Thrust Bearing ◽  
Thrust Load

Abstract This paper will show the influence of ambient pressure on the thrust capacity of bump-foil and spiral-groove gas thrust bearings. The bearings were operating in nitrogen at various pressures up to 69 bar, and were tested to failure. Failure was detected at various pressures by incrementally increasing the thrust load applied to the thrust bearing until the bearing was no longer thermally stable, or until contact was observed by a temperature spike measured by thermocouples within the bearing. These tests were performed on a novel thrust bearing test rig that was developed to allow thrust testing at pressures up to 207 bar cavity pressure at 260°C while rotating at speeds up to 120,000 rpm. The test rig floats on hydrostatic air bearings to allow for the direct measurement of applied thrust load through linkages that connect the stationary thrust loader to the rotor housing. Test results on a 65 mm (2.56 in) bump-foil thrust bearing at 100 krpm show a marked increase in load capacity with gas density, which has not previously been shown experimentally. Results also show that the load capacity of a similarly sized spiral-groove thrust bearing are relatively insensitive to pressure, and supported an order-of-magnitude less load than that observed for the bump-foil thrust bearing. These results are compared with analytical predictions, which agree reasonably with the experimental results. Predicted power loss is also presented for the bump-foil bearing; however, measured power loss was substantially higher.

Development of Foil Thrust Bearings with Simple Structure for Micro Turbines

2011 ◽  
Vol 368-373 ◽  
pp. 1392-1395 ◽  
Author(s):  
Quan Zhou ◽  
Yu Hou ◽  
Ru Gang Chen
Keyword(s):  
High Speed ◽  
Simple Structure ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Complicated Structure ◽  
Thrust Bearings ◽  
Foil Bearings ◽  
Rotational Systems ◽  
Micro Turbine ◽  
Foil Thrust Bearing

Because of the low power loss and high stability, foil bearings are suitable lubrication components for high speed rotational systems. At present, the foil bearings used in actual applications almost have complicated structure and are hard to manufacture. In this paper, two kinds of foil thrust bearings with simple structure are presented. Configurations of these two foil thrust bearings are introduced; meanwhile, the load capacity and running stability are also tested in a high speed micro turbine. It is shown that viscoelastic supported foil thrust bearing has higher load capacity and hemisphere convex dots supported foil thrust bearing is more stable in high speed operational condition.

Analysis of Starved Thrust Bearings Including Temperature Effects

1987 ◽  
Vol 109 (3) ◽  
pp. 395-401 ◽  
Author(s):  
A. Artiles ◽  
H. Heshmat
Keyword(s):  
Film Thickness ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Operating Conditions ◽  
Geometrical Parameters ◽  
Two Dimensional ◽  
Thrust Bearings ◽  
Direct Iteration ◽  
Finite Thrust ◽  
Raphson Iteration

A method of analysis is described treating starvation in finite thrust bearing pads. A variable-size finite difference mesh is used to represent the two-dimensional temperature and pressure fields. A combination of Newton-Raphson iteration, direct iteration, and column matrix methods are used to solve for the start-of-film and minimum film thickness as well as the coupled two-dimensional energy and Reynolds equations. A parametric study describes the performance characteristics of the tapered land thrust bearing (flowrates, extent of fluid film, temperature rises, load capacity and torque) for different minimum film thicknesses and levels of starvation. This study considered variations in the geometrical parameters such as pad aspect ratio (L/R2=1/3, 1/2, 2/3) and extent of the pad (β=27, 42, and 57 deg) with an optimum taper ratio (β1/β=0.8). It is found that the effects of starvation are fairly small near the flooded condition but accelerate rapidly below the 50 percent starvation level. The start of the film (θ1) depends mostly on the level of starvation, and is essentially independent of the geometrical parameters, operating conditions or film thickness.

Sign in / Sign up

Export Citation Format

Share Document