The Influence of Wing Span and Angle of Attack on Racing Car Wing/Wheel Interaction Aerodynamics

2017 ◽  
Vol 139 (6) ◽  
Author(s):  
Sammy Diasinos ◽  
Tracie J. Barber ◽  
Graham Doig
Keyword(s):  
Angle Of Attack ◽  
Ground Effect ◽  
Navier Stokes ◽  
Flow Structures ◽  
Wing Span ◽  
Complex Interactions ◽  
Lift And Drag ◽  
Two Bodies ◽  
Wing In Ground Effect

A numerical-based (Reynolds-averaged Navier–Stokes (RANS)) investigation into the role of span and wing angle in determining the performance of an inverted wing in ground effect located forward of a wheel is described, using a generic simplified wheel and NACA 4412 geometry. The complex interactions between the wing and wheel flow structures are investigated to explain either increases or decreases for the downforce and drag produced by the wing and wheel when compared to the equivalent body in isolation. Geometries that allowed the strongest primary wing vortex to pass along the inner face of the wheel resulted in the most significant reductions in lift and drag for the wheel. As a result, the wing span and angle combination that would produce the most downforce, or least drag, in the presence of the wheel does not coincide with what would be assumed if the two bodies were considered only in isolation demonstrating the significance of optimizing these two bodies in unison.

Large Eddy Simulation of the Flow Around a Diffuser-Equipped Bluff Body in Ground Effect

2011 ◽  
Author(s):  
Lara Schembri Puglisevich ◽  
Gary Page
Keyword(s):  
Large Eddy Simulation ◽  
Bluff Body ◽  
Vortex Formation ◽  
Ground Effect ◽  
Vortical Flow ◽  
Navier Stokes ◽  
Flow Structures ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Flow Features

Unsteady Large Eddy Simulation (LES) is carried out for the flow around a bluff body equipped with an underbody rear diffuser in close proximity to the ground, representing an automotive diffuser. The goal is to demonstrate the ability of LES to model underbody vortical flow features at experimental Reynolds numbers (1.01 × 106 based on model height and incoming velocity). The scope of the time-dependent simulations is not to improve on Reynolds-Averaged Navier Stokes (RANS), but to give further insight into vortex formation and progression, allowing better understanding of the flow, hence allowing more control. Vortical flow structures in the diffuser region, along the sides and top surface of the bluff body are successfully modelled. Differences between instantaneous and time-averaged flow structures are presented and explained. Comparisons to pressure measurements from wind tunnel experiments on an identical bluff body model shows a good level of agreement.

Stability Analysis of a Light Aircraft Configuration Using Computational Fluid Dynamics

2012 ◽  
Vol 225 ◽  
pp. 391-396 ◽  
Author(s):  
Mohammed Mahdi ◽  
Yasser A. Elhassan
Keyword(s):  
Numerical Simulation ◽  
Stokes Equations ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Rate Of Change ◽  
Navier Stokes ◽  
Rolling Moment ◽  
Moment Coefficient ◽  
Stability Derivatives ◽  
Lift And Drag

This work aims to simulate and study the flow field around SAFAT-01 aircraft using numerical solution based on solving Reynolds Averaged Navier-Stokes equations coupled with K-ω SST turbulent model. The aerodynamics behavior of SAFAT-01 aircraft developed at SAFAT aviation complex were calculated at different angles of attack and side slip angles. The x,y and z forces and moments were calculated at flight speed 50m/s and at sea level condition. Lift and drag curves for different angles of attack were plotted. The maximum lift coefficient for SAFAT-01 was 1.67 which occurred at angle of attack 16° and Maximum lift to drag ratio (L/D) was 14 which occurred at α=3°, and the zero lift drag coefficient was 0.0342. Also the yawing moment coefficient was plotted for different side slip angles as well as rolling moment. The longitudinal stability derivatives with respect to angle of attack, speed variation (u), rate of pitch (q) and time rate of change of angle of attack were calculated using obtained CFD results. Concerning lateral stability only side slips derivatives were calculated. To validate this numerical simulation USAF Digital DATCOM is used to analyze this aircraft; a comparison between predicted results for this aircraft and Digital DATCOM indicated that this numerical simulation has high ability for predicting the aerodynamics characteristics.

scholarly journals The Effect of Gurney Flap and Trailing-edge Wedge on the Aerodynamic Behavior of an Axial Turbine Blade

2021 ◽  
Vol 2 (4) ◽  
pp. 293-305
Author(s):  
Mohammad Mahdi Mahzoon ◽  
Masoud Kharati-Koopaee
Keyword(s):  
Angle Of Attack ◽  
Vortex Generator ◽  
Aerodynamic Performance ◽  
Trailing Edge ◽  
Blunt Trailing Edge ◽  
Gurney Flap ◽  
Maximum Increment ◽  
Lift And Drag ◽  
Lift And Drag Coefficient

In this research, the effect of Gurney flap and trailing-edge wedge on the aerodynamic behavior of blunt trailing-edge airfoil Du97-W-300 which is equipped with vortex generator is studied. To do this, the role of Gurney flap and trailing-edge wedge on the lift and drag coefficient and also aerodynamic performance of the airfoil is studied. Validation of the numerical model is performed by comparison of the obtained results with those of experiment. Results show that before stall, Gurney flap leads to the increase in the aerodynamic performance in a wider range of angle of attack. Numerical findings reveal that the maximum increment for the aerodynamic performance is obtained at low angle of attack when trailing-edge wedge is employed. It is found that for the highest considered value of Gurney flap and trailing-edge wedge heights, where the highest values for the lift occur, the higher aerodynamic performance at low angle of attack is obtained when trailing-edge wedge is used and at high angle of attack, the Gurney flap results in a higher aerodynamic performance. It is also shown that when high aerodynamic performance is concerned, addition of Gurney flap to the airfoil leads to the higher value for the lift. Doi: 10.28991/HIJ-2021-02-04-03 Full Text: PDF

An analysis of aerodynamic forces on a delta wing

1996 ◽  
Vol 316 ◽  
pp. 173-196 ◽  
Author(s):  
Chien-Cheng Chang ◽  
Sheng-Yuan Lei
Keyword(s):  
Mach Number ◽  
Stokes Equations ◽  
Delta Wing ◽  
Leading Edge ◽  
Navier Stokes ◽  
Flow Structures ◽  
Aerodynamic Forces ◽  
Navier Stokes Equations ◽  
Lift And Drag ◽  
Secondary Vortices

The present study aims at relating lift and drag to flow structures around a delta wing of elliptic section. Aerodynamic forces are analysed in terms of fluid elements of non-zero vorticity and density gradient. The flow regime considered is Mα = 0.6 ∼ 1.8 and α = 5° ∼ 19°, where Mα denotes the free-stream Mach number and α the angle of attack. Let ρ denote the density, u velocity, and ω vorticity. It is found that there are two major source elements Re(x) and Ve(x) which contribute about 95% or even more to the aerodynamic forces for all the cases under consideration, \[R_e({\bm x})=-\frac{1}{2} {\bm u}^2 \nabla\rho \cdot \nabla\phi\quad {\rm and}\quad V_e ({\bm x}) = -\rho{\bm u}\times {\bm \omega}\cdot \nabla\phi,\] where θ is an acyclic potential, generated by the delta wing moving with unit velocity in the negative direction of the force (lift or drag). All the physical quantities are non-dimensionalized. Detailed force contributions are analysed in terms of the flow structures and the elements Re(x) and Ve(x). The source elements Re(x) and Ve(x) are concentrated in the following regions: the boundary layer in front of (below) the delta wing, the primary and secondary vortices over the delta wing, and a region of expansion around the leading edge. It is shown that Ve(x) due to vorticity prevails as the source of forces at relatively low Mach number, Mα < 0.7. Above about Mα = 0.75, Re(x) due to compressibility generally becomes the dominating contributor to the lift, while the overall contribution from Ve(x) decreases with increasing Mα, and even becomes negative at Mα = 1.2 for the lift, and at a higher Mα for the drag. The analysis is carried out with the aid of detailed numerical results by solving the Reynolds-averaged Navier–Stokes equations, which are in close agreement with experiments in comparisons of the surface pressure distributions.

scholarly journals Numerical Simulation on Aerodynamics of Multi-Element Airfoil with Drooped Spoiler in Ground Effect

2019 ◽  
Vol 37 (1) ◽  
pp. 167-176
Author(s):  
Jiang Liu ◽  
Junqiang Bai ◽  
Guozhu Gao ◽  
Min Chang ◽  
Nan Liu
Keyword(s):  
Lift Coefficient ◽  
Angle Of Attack ◽  
Ground Effect ◽  
Lower Surface ◽  
Navier Stokes ◽  
High Angle ◽  
High Angle Of Attack ◽  
Ride Height ◽  
Navier Stokes Equation ◽  
Sst Turbulence Model

By using the finite volume method and k-ω SST turbulence model to solve the Reynolds Average Navier-Stokes equation and using the slipping wall to simulate the relative movement of the ground, the ground effect on the aerodynamic characteristic of multi-element airfoil with drooped spoiler is investigated numerically, and the reason why the lift coefficient decreased in ground effect is analyzed. The results indicate that, with the reduction in ride height, the lift and the drag decrease and the lift-drag ratio increases for the multi-element airfoil; the amplitude of the reduction in the lift coefficient increases with the reduction in ride height and the increase in the angle of attack, the maximum of lift coefficient can be reduced by about 22%; with the effect of ground, the losses of suction at upper surface make the lift decrease, the increases of pressure at lower surface make the lift increase, the variation of the lift coefficient for the main wing caused by the former is more than three times that of the latter. Analyzing the reason why the lift coefficient decreases showed that:on the one hand, ground effect on the lift coefficient for clean airfoil is changed with the range of angle of attack. For the low-to-moderate angle of attack, the lift coefficient increases; for the high angle of attack, the lift coefficient decreases. But multi-element airfoil works in the takeoff and landing stage for the high angle of attack, which causes the reduction of the lift coefficient in ground effect. On the other hand, the increase of the lift coefficient caused by the deflection of spoiler decreases with the reduction in ride height and the maximum reduction can be about 50%, which illustrates that ground effect makes interaction of the front and back section for the multi-element airfoil weak, resulting in further decreasing the coefficient for the multi-element airfoil.

A Computational Study of the Flow Around an Isolated Wheel in Contact With the Ground

2005 ◽  
Vol 128 (3) ◽  
pp. 520-530 ◽  
Author(s):  
James McManus ◽  
Xin Zhang
Keyword(s):  
Computational Study ◽  
Experimental Results ◽  
Navier Stokes ◽  
Flow Structures ◽  
Road Vehicles ◽  
Accurate Representation ◽  
Drag Forces ◽  
Mechanisms Of Formation ◽  
Lift And Drag ◽  
Good Agreement

The flow around an isolated wheel in contact with the ground is computed by the Unsteady Reynolds-Averaged Navier-Stokes (URANS) method. Two cases are considered, a stationary wheel on a stationary ground and a rotating wheel on a moving ground. The computed wheel geometry is a detailed and accurate representation of the geometry used in the experiments of Fackrell and Harvey. The time-averaged computed flow is examined to reveal both new flow structures and new details of flow structures known from previous experiments. The mechanisms of formation of the flow structures are explained. A general schematic picture of the flow is presented. Surface pressures and pressure lift and drag forces are computed and compared to experimental results and show good agreement. The grid sensitivity of the computations is examined and shown to be small. The results have application to the design of road vehicles.

scholarly journals Wake behind a Compound Wing in Ground Effect

2020 ◽  
Vol 8 (3) ◽  
pp. 156 ◽  
Author(s):  
Saeed Jamei ◽  
Adi Maimun ◽  
Rasul Niazmand Bilandi ◽  
Nor Azwadi ◽  
Simone Mancini ◽  
...  
Keyword(s):  
Ground Effect ◽  
Lower Surface ◽  
Flow Structures ◽  
Physical Domain ◽  
Turbulent Model ◽  
Computational Simulations ◽  
Crucial Point ◽  
Pressure Distributions ◽  
Reverse Taper ◽  
Wing In Ground Effect

Flow structure is a crucial point for the conceptual design of Wing-in-Ground effect (WIG) crafts. In this study, pressure distributions around a compound wing, velocity and the turbulent intensity distribution in the wake area after trailing of the wing, have been investigated numerically. Computational simulations were completed regarding various angles of attack in-ground-effect. Two parts made up the compound wing: The first composed by one rectangular wing in the center, the second composed by a reverse taper wing, consisting of an anhedral angle at the side. A realizable k-ε turbulent model exhibited the flow field in the physical domain about the wing surface. The numerical results of the compound wing were validated using the data provided by wind tunnel tests. The flow structures around the compound wing were compared with that of a rectangular wing for different conditions. It was found that the pressure distribution on the rectangular wing was weaker than at the lower surface for the compound wing. However, the suction effect on the upper surface of the rectangular wing was higher. Also, the velocity defect and the turbulence level in the wake area was greater behind the compound wing.

Ground Effect on the Vortex Flow and Aerodynamics of a Slender Delta Wing

2018 ◽  
Vol 140 (7) ◽  
Author(s):  
T. Lee ◽  
L. S. Ko
Keyword(s):  
Vortex Breakdown ◽  
Delta Wing ◽  
Leading Edge ◽  
Ground Effect ◽  
Drag Forces ◽  
Wing Chord ◽  
Ground Distance ◽  
Lift And Drag ◽  
Wing Stall ◽  
Wing In Ground Effect

The ground effect on the aerodynamic loading and leading-edge vortex (LEV) flow generated by a slender delta wing was investigated experimentally. Both the lift and drag forces were found to increase with reducing ground distance (up to 50% of the wing chord). The lift increment was also found to be the greatest at low angles of attack α and decreased rapidly with increasing ground distance and α. The ground effect-caused earlier wing stall was also accompanied by a strengthened LEV with an increased rotational speed and size compared to the baseline wing. The smaller the ground distance, the stronger the LEV and the earlier vortex breakdown became. Meanwhile, the vortex trajectory was also found to be located further inboard and above the delta wing in ground effect compared to its baseline-wing counterpart. Finally, for wing-in-ground effect (WIG) craft with delta-wing planform the most effective in-ground-effect flight should be kept within 10% of the wing chord.

scholarly journals Numerical Testing of the Wing-in-Ground Effect on Aerodynamic Characteristics

2016 ◽  
Vol 7 (4) ◽  
pp. 115-0
Author(s):  
Stanisław WRZESIEŃ ◽  
Michał FRANT ◽  
Maciej MAJCHER
Keyword(s):  
Numerical Evaluation ◽  
Angle Of Attack ◽  
Ground Effect ◽  
Aerodynamic Characteristics ◽  
Proximity Effects ◽  
Flight Altitude ◽  
Numerical Testing ◽  
Ground Effects ◽  
Wing In Ground Effect

This paper presents the numerical evaluation of ground (proximity) effects on the basic aerodynamic characteristics of a specifically designed airplane model. The ground effects were investigated in relation to the angle of attack and flight altitude. The results were referenced to the characteristics of an object in motion unaffected by ground effects.

Sign in / Sign up

Export Citation Format

Share Document