scholarly journals The Effect of Water Droplet Size, Temperature, and Impingement Velocity on Gold Wettability at the Nanoscale

2017 ◽  
Vol 5 (3) ◽  
Author(s):  
Jhonatam Cordeiro ◽  
Salil Desai
Keyword(s):  
Contact Angle ◽  
Droplet Size ◽  
Water Droplet ◽  
Molecular Diffusion ◽  
Dynamic Contact Angle ◽  
Contact Angles ◽  
Gold Substrate ◽  
Stabilization Time ◽  
Lower Contact ◽  
Impingement Velocity

Molecular dynamics (MD) simulations are performed to investigate the wettability of gold substrate interacting with nanosized droplets of water. The effects of droplet size, temperature variation, and impingement velocity are evaluated using molecular trajectories, dynamic contact angle, spread ratios, radial distribution function (RDF), and molecular diffusion graphs. Droplets of 4 nm and 10 nm were simulated at 293 K and 373 K, respectively. Stationary droplets were compared to droplets impinging the substrate at 100 m/s. The simulations were executed on high-end workstations equipped with NVIDIA® Tesla graphical processing units (GPUs). Results show that smaller droplets have a faster stabilization time and lower contact angles than larger droplets. With an increase in temperature, stabilization time gets faster, and the molecular diffusion from the water droplet increases. Higher temperatures also increase the wettability of the gold substrate, wherein droplets present a lower contact angle and a higher spread ratio. Droplets that impact the substrate at a higher impingement velocity converge to the same contact angle as stationary droplets. At higher temperatures, the impingement velocities accelerate the diffusion of water molecules into vapor. It was revealed that impingement velocities do not influence stabilization times. This research establishes relationships among different process parameters to control the wettability of water on gold substrates which can be explored to study several nanomanufacturing processes.

scholarly journals Numerical Bifurcation Analysis of a Film Flowing over a Patterned Surface through Enhanced Lubrication Theory

Fluids ◽  
2021 ◽  
Vol 6 (11) ◽  
pp. 405
Author(s):  
Nicola Suzzi ◽  
Giulio Croce
Keyword(s):  
Contact Angle ◽  
Bifurcation Analysis ◽  
Dynamic Contact Angle ◽  
Flow Characteristics ◽  
Dynamic Contact ◽  
Contact Angles ◽  
Inclined Plate ◽  
Lubrication Equation ◽  
Static Contact ◽  
Numerical Bifurcation

The bifurcation analysis of a film falling down an hybrid surface is conducted via the numerical solution of the governing lubrication equation. Instability phenomena, that lead to film breakage and growth of fingers, are induced by multiple contamination spots. Contact angles up to 75∘ are investigated due to the full implementation of the free surface curvature, which replaces the small slope approximation, accurate for film slope lower than 30∘. The dynamic contact angle is first verified with the Hoffman–Voinov–Tanner law in case of a stable film down an inclined plate with uniform surface wettability. Then, contamination spots, characterized by an increased value of the static contact angle, are considered in order to induce film instability and several parametric computations are run, with different film patterns observed. The effects of the flow characteristics and of the hybrid pattern geometry are investigated and the corresponding bifurcation diagram with the number of observed rivulets is built. The long term evolution of induced film instabilities shows a complex behavior: different flow regimes can be observed at the same flow characteristics under slightly different hybrid configurations. This suggest the possibility of controlling the rivulet/film transition via a proper design of the surfaces, thus opening the way for relevant practical application.

Numerical Study of a Small Droplet Movement in a Microchannel under Heat Source

2019 ◽  
Vol 894 ◽  
pp. 104-111
Author(s):  
Thanh Long Le ◽  
Jyh Chen Chen ◽  
Huy Bich Nguyen
Keyword(s):  
Contact Angle ◽  
Heat Source ◽  
Water Droplet ◽  
Stokes Equations ◽  
Numerical Study ◽  
Dynamic Contact Angle ◽  
Dynamic Contact ◽  
Initial Position ◽  
Immiscible Fluids ◽  
Two Phase

In this study, the numerical computation is used to investigate the transient movement of a water droplet in a microchannel. For tracking the evolution of the free interface between two immiscible fluids, we employed the finite element method with the two-phase level set technique to solve the Navier-Stokes equations coupled with the energy equation. Both the upper wall and the bottom wall of the microchannel are set to be an ambient temperature. 40mW heat source is placed at the distance of 1 mm from the initial position of a water droplet. When the heat source is turned on, a pair of asymmetric thermocapillary convection vortices is formed inside the droplet and the thermocapillary on the receding side is smaller than that on the advancing side. The temperature gradient inside the droplet increases quickly at the initial times and then decreases versus time. Therefore, the actuation velocity of the water droplet first increases significantly, and then decreases continuously. The dynamic contact angle is strongly affected by the oil flow motion and the net thermocapillary momentum inside the droplet. The advancing contact angle is always larger than the receding contact angle during actuation process.

Molecular Simulation of the Contact Angle of Water Droplet on a Platinum Surface

2005 ◽  
Author(s):  
Bo Shi ◽  
Shashank Sinha ◽  
Vijay K. Dhir
Keyword(s):  
Contact Angle ◽  
Molecular Simulation ◽  
Simulation Study ◽  
Water Droplet ◽  
Solid Wall ◽  
Contact Angles ◽  
Water Droplets ◽  
Platinum Surface

This paper presents a molecular simulation study of the contact angles of water droplets on a platinum surface for a range of temperatures. SPC/E and Z-P model are used for the water-water and water-platinum potentials, respectively. The results show that the contact angle decreases with the increase of system temperatures and increases when the potential decreases. When the temperature is high enough, the contact angles drop to zero degrees. The results were compared with the argon-virtual solid wall and water-Aluminum results, a similar trend was found.

Spreading-Droplet Simulation With Surface Tension Model Using Inter-Particle Force in Particle Method

2013 ◽  
Author(s):  
Eiji Ishii ◽  
Taisuke Sugii
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Dynamic Contact Angle ◽  
Particle Method ◽  
Dynamic Contact ◽  
Contact Angles ◽  
Particle Methods ◽  
Static Contact ◽  
Particle Force ◽  
Surface Tension Model

Predicting the spreading behavior of droplets on a wall is important for designing micro/nano devices used for reagent dispensation in micro-electro-mechanical systems, printing processes of ink-jet printers, and condensation of droplets on a wall during spray forming in atomizers. Particle methods are useful for simulating the behavior of many droplets generated by micro/nano devices in practical computational time; the motion of each droplet is simulated using a group of particles, and no particles are assigned in the gas region if interactions between the droplets and gas are weak. Furthermore, liquid-gas interfaces obtained from the particle method remain sharp by using the Lagrangian description. However, conventional surface tension models used in the particle methods are used for predicting the static contact angle at a three-phase interface, not for predicting the dynamic contact angle. The dynamic contact angle defines the shape of a spreading droplet on a wall. We previously developed a surface tension model using inter-particle force in the particle method; the static contact angle of droplets on the wall was verified at various contact angles, and the heights of droplets agreed well with those obtained theoretically. In this study, we applied our surface tension model to the simulation of a spreading droplet on a wall. The simulated dynamic contact angles for some Weber numbers were compared with those measured by Šikalo et al, and they agreed well. Our surface tension model was useful for simulating droplet motion under static and dynamic conditions.

scholarly journals Study of Fluids Motion in a Microchannel under Heat Source

2020 ◽  
Vol 2 (SI2) ◽  
pp. First
Author(s):  
Long Thanh Le
Keyword(s):  
Contact Angle ◽  
Heat Source ◽  
Water Droplet ◽  
Stokes Equations ◽  
Dynamic Contact Angle ◽  
Dynamic Contact ◽  
Immiscible Fluids ◽  
Navier Stokes ◽  
Two Phase ◽  
Receding Contact Angle

In this study, the numerical computation is used to investigate the transient thermocapillary migration of a water droplet in a Microchannel. For tracking the evolution of the free interface between two immiscible fluids, we employed the finite element method with the two-phase level set technique to solve the Navier-Stokes equations coupled with the energy equation. Both the upper wall and the bottom wall of the microchannel are set to be an ambient temperature. The heat source is placed at the left side of a water droplet. When the heat source is turned on, a pair of asymmetric thermocapillary convection vortices is formed inside the droplet and the thermocapillary on the receding side is smaller than that on the advancing side. The temperature gradient inside the droplet increases quickly at the initial times and then decreases versus time. Therefore, the actuation velocity of the water droplet first increases significantly, and then decreases continuously. The dynamic contact angle is strongly affected by the oil flow motion and the net thermocapillary momentum inside the droplet. The advancing contact angle is always larger than the receding contact angle during actuation process.

Measurements of the Contact Angles for Various Fluids Which Are Widely Used in the Oilfields to Improve Oil Recovery

2018 ◽  
Author(s):  
M. Elsharafi ◽  
K. Vidal ◽  
R. Thomas
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Interfacial Tension ◽  
Oil Recovery ◽  
Dynamic Contact Angle ◽  
Dynamic Contact ◽  
Contact Angles ◽  
Rock Face ◽  
Angle Measurements ◽  
Contact Angle Measurements

Contact angle measurements are important to determine surface and interfacial tension between solids and fluids. A ‘water-wet’ condition on the rock face is necessary in order to extract oil. In this research, the objectives are to determine the wettability (water-wet or oil-wet), analyze how different brine concentrations will affect the wettability, and study the effect of the temperature on the dynamic contact angle measurements. This will be carried out by using the Cahn Dynamic Contact Angle. Analyzer DCA 315 to measure the contact angle between different fluids such as surfactant, alkaline, and mineral oil. This instrument is also used to measure the surface properties such as surface tension, contact angle, and interfacial tension of solid and liquid samples by using the Wilhelmy technique. The work used different surfactant and oil mixed with different alkaline concentrations. Varying alkaline concentrations from 20ml to 1ml were used, whilst keeping the surfactant concentration constant at 50ml.. It was observed that contact angle measurements and surface tension increase with increased alkaline concentrations. Therefore, we can deduce that they are directly proportional. We noticed that changing certain values on the software affected our results. It was found that after calculating the density and inputting it into the CAHN software, more accurate readings for the surface tension were obtained. We anticipate that the surfactant and alkaline can change the surface tension of the solid surface. In our research, surfactant is desirable as it maintains a high surface tension even when alkaline percentage is increased.

Hydrosilation-Cured Poly(dimethylsiloxane) Networks:  Intrinsic Contact Angles via Dynamic Contact Angle Analysis

2003 ◽  
Vol 36 (10) ◽  
pp. 3689-3694 ◽  
Author(s):  
Janelle M. Uilk ◽  
Ann E. Mera ◽  
Robert B. Fox ◽  
Kenneth J. Wynne
Keyword(s):  
Contact Angle ◽  
Dynamic Contact Angle ◽  
Dynamic Contact ◽  
Contact Angles ◽  
Contact Angle Analysis

Analysis of Wetting of Perylene Diimide Thin Films-on-Glass by Water

2013 ◽  
Vol 594-595 ◽  
pp. 1074-1077
Author(s):  
V. Madhurima ◽  
K. Greeshma Priyanka ◽  
K.S.N.D. Pavan ◽  
S. Nagarajan
Keyword(s):  
Thin Films ◽  
Contact Angle ◽  
Photophysical Properties ◽  
Contact Angles ◽  
Alkyl Chains ◽  
Glass Substrates ◽  
Angle Data ◽  
Type Semiconductor ◽  
Polar Derivatives ◽  
Lower Contact

Perylene tetracarboxylic diimide (PTCDI), derivatives have attracted the attention of the scientific community owing to their thermal stability, electron affinity-enabling n-type semiconductor behaviour and useful photophysical properties. Thin films of six new perylene tetracarboxylic diimides were fabricated on glass substrate by spin coating. The contact angles made by water on these six substrates, some with alkyl chain derivatives and the others with polar side chains, were measured using a precision contact angle goniometer. The alignment of these films on glass substrates are inferred from the contact angle data and the results are compared with those of the (self) alignment in liquid state. Derivatives with alkyl chains were seen to interact more with water, causing a lower contact angle compared to the more polar derivatives. This counter-intuitive result is interpreted in terms of molecular alignment of samples on the glass substrates.

scholarly journals Does the Use of Adjuvants Alter Surface Tension and Contact Angle of Herbicide Spray Droplets on Leaves of Sida spp.?

2019 ◽  
Vol 37 ◽  
Author(s):  
R.T.S. SANTOS ◽  
M.C. FERREIRA ◽  
R.G. VIANA
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Contact Angles ◽  
Control Surface ◽  
Droplet Spreading ◽  
Spray Solution ◽  
Randomized Design ◽  
Plant Surfaces ◽  
Sida Rhombifolia ◽  
Lower Contact

ABSTRACT: Droplet spreading on plant surfaces may indicate greater efficiency in herbicide application. The aim of this study was to evaluate surface tension and contact angle of the aminopyralid + fluroxypir herbicide droplets associated with adjuvants on the leaf surface of three species of the genus Sida. The experiment was carried out in a completely randomized design, in a 4x2+1 factorial arrangement, with four replications. Four treatments containing two rates of the herbicide (0.04 + 0.08 kg a.i. ha-1 and 0.08+0.16 kg a.i. ha-1) were evaluated, associated or not with the adjuvants vegetable oil, mineral oil and lecthin; and water was used as a control. Surface tension and contact angle of the syringes were measured with a tensiometer. Surface tension was evaluated at 5, 15 and 25 seconds after droplet formation. Contact angle was measured at 5, 15 and 25 seconds after droplet deposition on the adaxial and abaxial surfaces of Sida rhombifolia, S. glaziovii and S. cordifolia. The results were submitted to analysis of variance by the F-test and the means of the treatments were compared by Tukey’s test (p>0.05). There was no interaction between the factors for surface tension. The contact angles of S. cordifolia and S. glaziovii were lower after addition of lecthin on the adaxial face. The addition of the adjuvants to the spray solution provided lower contact angles at the rate of 0.04 + 0.08 kg a.i. ha-1, except for S. rhombifolia, whose contact angle was lower with the spray solution without adjuvant.

Sign in / Sign up

Export Citation Format

Share Document