Effects of Real Gas Model Accuracy and Operating Conditions on Supercritical CO2 Compressor Performance and Flow Field

2018 ◽  
Vol 140 (6) ◽  
Author(s):  
Alireza Ameli ◽  
Ali Afzalifar ◽  
Teemu Turunen-Saaresti ◽  
Jari Backman
Keyword(s):  
Flow Field ◽  
Critical Point ◽  
Supercritical Co2 ◽  
High Efficiency ◽  
Significant Proportion ◽  
Operating Conditions ◽  
Working Fluid ◽  
Look Up Table ◽  
Compressor Performance ◽  
The Look

Rankine and Brayton cycles are common energy conversion cycles and constitute the basis of a significant proportion of global electricity production. Even a seemingly marginal improvement in the efficiency of these cycles can considerably decrease the annual use of primary energy sources and bring a significant gain in power plant output. Recently, supercritical Brayton cycles using CO2 as the working fluid have attracted much attention, chiefly due to their high efficiency. As with conventional cycles, improving the compressor performance in supercritical cycles is major route to increasing the efficiency of the whole process. This paper numerically investigates the flow field and performance of a supercritical CO2 centrifugal compressor. A thermodynamic look-up table is coupled with the flow solver, and the look-up table is systematically refined to take into account the large variation of thermodynamic properties in the vicinity of the critical point. Effects of different boundary and operating conditions are also discussed. It is shown that the compressor performance is highly sensitive to the look-up table resolution as well as the operating and boundary conditions near the critical point. Additionally, a method to overcome the difficulties of simulation close to the critical point is explained.

Effects of Real Gas Model Accuracy and Operating Conditions on Supercritical CO2 Compressor Performance and Flow Field

2017 ◽  
Author(s):  
Alireza Ameli ◽  
Ali Afzalifar ◽  
Teemu Turunen-Saaresti ◽  
Jari Backman
Keyword(s):  
Flow Field ◽  
Critical Point ◽  
Supercritical Co2 ◽  
High Efficiency ◽  
Significant Proportion ◽  
Operating Conditions ◽  
Working Fluid ◽  
Look Up Table ◽  
Compressor Performance ◽  
The Look

Rankine and Brayton cycles are common energy conversion cycles and constitute the basis of a significant proportion of global electricity production. Even a seemingly marginal improvement in the efficiency of these cycles can considerably decrease the annual use of primary energy sources and bring a significant gain in power plant output. Recently, supercritical Brayton cycles using CO2 as the working fluid have attracted much attention, chiefly due to their high efficiency. As with conventional cycles, improving the compressor performance in supercritical cycles is major route to increasing the efficiency of the whole process. This paper numerically investigates the flow field and performance of a supercritical CO2 centrifugal compressor. A thermodynamic look-up table is coupled with the flow solver and the look-up table is systematically refined to take into account the large variation of thermodynamic properties in the vicinity of the critical point. Effects of different boundary and operating conditions are also discussed. It is shown that the compressor performance is highly sensitive to the look-up table resolution as well as the operating and boundary conditions near the critical point. Additionally, a method to overcome the difficulties of simulation close to the critical point is explained.

Computational Fluid Dynamics of a Radial Compressor Operating With Supercritical CO2

2012 ◽  
Author(s):  
Rene Pecnik ◽  
Enrico Rinaldi ◽  
Piero Colonna
Keyword(s):  
Critical Point ◽  
Gas Turbine ◽  
Supercritical Co2 ◽  
High Speed ◽  
Power Plants ◽  
Compressible Flows ◽  
High Efficiency ◽  
Fluid Dynamic ◽  
Working Fluid ◽  
Maximum Pressure

The merit of using supercritical CO2 (scCO2) as the working fluid of a closed Brayton cycle gas turbine is now widely recognized, and the development of this technology is now actively pursued. scCO2 gas turbine power plants are an attractive option for solar, geothermal and nuclear energy conversion. Among the challenges which must be overcome in order to successfully bring the technology to the market, the efficiency of the compressor and turbine operating with the supercritical fluid should be increased as much as possible. High efficiency can be reached by means of sophisticated aerodynamic design, which, compared to other overall efficiency improvements, like cycle maximum pressure and temperature increase, or increase of recuperator effectiveness, does not require an increase in equipment cost, but only an additional effort in research and development. This paper reports a three-dimensional CFD study of a high-speed centrifugal compressor operating with CO2 in the thermodynamic region slightly above the vapor-liquid critical point. The investigated geometry is the compressor impeller tested in the Sandia scCO2 compression loop facility [1]. The fluid dynamic simulations are performed with a fully implicit parallel Reynolds-averaged Navier-Stokes code based on a finite volume formulation on arbitrary polyhedral mesh elements. The CFD code has been validated on test cases which are relevant for this study, see Ref. [2,3]. In order to account for the strongly nonlinear variation of the thermophysical properties of supercritical CO2, the CFD code is coupled with an extensive library for the computation of properties of fluids and mixtures [4]. Among the available models, the one based on reference equations of state for CO2 [5,6] has been selected, as implemented in one of the sub-libraries [7]. A specialized look-up table approach and a meshing technique suited for turbomachinery geometries are also among the novelties introduced in the developed methodology. A detailed evaluation of the CFD results highlights the challenges of numerical studies aimed at the simulation of technically relevant compressible flows occurring close to the liquid-vapor critical point. The data of the obtained flow field are used for a comparison with experiments performed at the Sandia scCO2 compression-loop facility.

Study of the Similarity Laws for Supercritical CO2 Turbine Performance Testing Using High Pressurized Air

2018 ◽  
Author(s):  
Qiyu Ying ◽  
Weilin Zhuge ◽  
Yangjun Zhang ◽  
Panpan Song ◽  
Lei Zhang
Keyword(s):  
Flow Field ◽  
Experimental Method ◽  
Supercritical Co2 ◽  
Performance Testing ◽  
Operating Conditions ◽  
Similarity Criteria ◽  
Working Fluid ◽  
Turbine Performance ◽  
Cfd Method ◽  
Similarity Laws

Closed regenerative Brayton cycle utilizing supercritical CO2 as working fluid has attracted more concern recently as it offers high cycle thermal efficiency and decreases size of turbomachinery. The performance testing of the CO2 turbine is very important for the supercritical CO2 cycle development. However, testing the turbine performance in a closed supercritical CO2 cycle is of difficulty and complication. This paper proposes a novel experimental method on CO2 turbine testing using high pressurized air as surrogate fluid. The performance similarity laws for the experimental method are studied, because traditional similarity criteria are not applicable since supercritical CO2 and high pressurized air are both non-ideal gases. A CO2 turbine is simulated by the CFD method under similar operating conditions with CO2 and high pressurized air, and turbine performance and flow field is analyzed. CFD analysis results show that turbine’s overall performance matches up well, and difference of parameter in flow field is small. The proposed experimental method can be used for CO2 turbine performance testing without setting up the complex closed supercritical CO2 cycle test bench.

Effect of Impurities on Compressor and Cooler in Supercritical CO2 Cycles

2018 ◽  
Vol 141 (1) ◽  
Author(s):  
Ladislav Vesely ◽  
K. R. V. Manikantachari ◽  
Subith Vasu ◽  
Jayanta Kapat ◽  
Vaclav Dostal ◽  
...  
Keyword(s):  
Critical Point ◽  
Carbon Capture ◽  
Nuclear Power ◽  
Power Plants ◽  
High Efficiency ◽  
Waste Heat ◽  
Operating Conditions ◽  
Working Fluid ◽  
Compressor Inlet ◽  
Almost All

With the increasing demand for electric power, the development of new power generation technologies is gaining increased attention. The supercritical carbon dioxide (S-CO2) cycle is one such technology, which has relatively high efficiency, compactness, and potentially could provide complete carbon capture. The S-CO2 cycle technology is adaptable for almost all of the existing heat sources such as solar, geothermal, fossil, nuclear power plants, and waste heat recovery systems. However, it is known that optimal combinations of operating conditions, equipment, working fluid, and cycle layout determine the maximum achievable efficiency of a cycle. Within an S-CO2 cycle, the compression device is of critical importance as it is operating near the critical point of CO2. However, near the critical point, the thermo-physical properties of CO2 are highly sensitive to changes of pressure and temperature. Therefore, the conditions of CO2 at the compressor inlet are critical in the design of such cycles. Also, the impurity species diluted within the S-CO2 will cause deviation from an ideal S-CO2 cycle as these impurities will change the thermodynamic properties of the working fluid. Accordingly, the current work examines the effects of different impurity compositions, considering binary mixtures of CO2 and He, CO, O2, N2, H2, CH4, or H2S on various S-CO2 cycle components. The second part of the study focuses on the calculation of the basic cycles and component efficiencies. The results of this study will provide guidance and define the optimal composition of mixtures for compressors and coolers.

Computational Fluid Dynamics of a Radial Compressor Operating With Supercritical CO2

2012 ◽  
Vol 134 (12) ◽  
Author(s):  
Rene Pecnik ◽  
Enrico Rinaldi ◽  
Piero Colonna
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Critical Point ◽  
Gas Turbine ◽  
Supercritical Co2 ◽  
Power Plants ◽  
Compressible Flows ◽  
High Efficiency ◽  
Working Fluid ◽  
Maximum Pressure

The merit of using supercritical CO2(scCO2) as the working fluid of a closed Brayton cycle gas turbine is now widely recognized, and the development of this technology is now actively pursued. scCO2 gas turbine power plants are an attractive option for solar, geothermal, and nuclear energy conversion. Among the challenges that must be overcome in order to successfully bring the technology to the market is that the efficiency of the compressor and turbine operating with the supercritical fluid should be increased as much as possible. High efficiency can be reached by means of sophisticated aerodynamic design, which, compared to other overall efficiency improvements, like cycle maximum pressure and temperature increase, or increase of recuperator effectiveness, does not require an increase in equipment cost, but only an additional effort in research and development. This paper reports a three-dimensional computational fluid dynamics (CFD) study of a high-speed centrifugal compressor operating with CO2 in the thermodynamic region slightly above the vapor–liquid critical point. The investigated geometry is the compressor impeller tested in the Sandia scCO2 compression loop facility. The fluid dynamic simulations are performed with a fully implicit parallel Reynolds-averaged Navier–Stokes code based on a finite volume formulation on arbitrary polyhedral mesh elements. In order to account for the strongly nonlinear variation of the thermophysical properties of supercritical CO2, the CFD code is coupled with an extensive library for the computation of properties of fluids and mixtures. A specialized look-up table approach and a meshing technique suited for turbomachinery geometries are also among the novelties introduced in the developed methodology. A detailed evaluation of the CFD results highlights the challenges of numerical studies aimed at the simulation of technically relevant compressible flows occurring close to the liquid–vapor critical point. The data of the obtained flow field are used for a comparison with experiments performed at the Sandia scCO2 compression-loop facility.

Effect of Mixtures on Compressor and Cooler in Supercritical Carbon Dioxide Cycles

2018 ◽  
Author(s):  
Ladislav Vesely ◽  
K. R. V. Manikantachari ◽  
Subith Vasu ◽  
Jayanta Kapat ◽  
Vaclav Dostal ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Supercritical Carbon Dioxide ◽  
Critical Point ◽  
Carbon Capture ◽  
Power Plants ◽  
High Efficiency ◽  
Waste Heat ◽  
Operating Conditions ◽  
Working Fluid ◽  
Supercritical Carbon

With the increasing demand for electric power, the development of new power generation technologies is gaining increased attention. The supercritical carbon dioxide (S-CO2) cycle is one such technology, which has relatively high efficiency, compactness, and potentially could provide complete carbon capture. The S-CO2 cycle technology is adaptable for almost all of the existing heat sources such as solar, geothermal, fossil, nuclear power plants, and waste heat recovery systems. However, it is known that, optimal combinations of: operating conditions, equipment, working fluid, and cycle layout determine the maximum achievable efficiency of a cycle. Within an S-CO2 cycle the compression device is of critical importance as it is operating near the critical point of CO2. However, near the critical point, the thermo-physical properties of CO2 are highly sensitive to changes of pressure and temperature. Therefore, the conditions of CO2 at the compressor inlet are critical in the design of such cycles. Also, the impurity species diluted within the S-CO2 will cause deviation from an ideal S-CO2 cycle as these impurities will change the thermodynamic properties of the working fluid. Accordingly the current work examines the effects of different impurity compositions, considering binary mixtures of CO2 and: He, CO, O2, N2, H2, CH4, or H2S; on various S-CO2 cycle components. The second part of the study focuses on the calculation of the basic cycles and component efficiencies. The results of this study will provide guidance and defines the optimal composition of mixtures for compressors and coolers.

Preliminarily Design of Supercritical CO2 Compression Test System

2021 ◽  
Author(s):  
Geng Teng ◽  
Laijie Chen ◽  
Xin Shen ◽  
Hua Ouyang ◽  
Yubo Zhu ◽  
...  
Keyword(s):  
Simulation Model ◽  
Compression Test ◽  
Thermodynamic Model ◽  
Supercritical Co2 ◽  
Operating Performance ◽  
Test System ◽  
Operating Conditions ◽  
Working Fluid ◽  
Stable Operation ◽  
Test Loop

Abstract The centrifugal compressor is the core component of the supercritical carbon dioxide (SCO2) power cycle. It is essential to carry out component-level experimental research on it and test the working characteristics of the compressor and its auxiliary equipment. Building an accurate closed-loop simulation model of closed SCO2 compression loop is a necessary preparation for selecting loop key parameters and establishing system control strategy, which is also an important prerequisite for the stable operation of compressor under test parameters. In this paper, the thermodynamic model of compressor, pre-cooler, orifice plate and other components in supercritical CO2 compression test system is studied, and the simulation model of compression test system is established. Moreover, based on the system enthalpy equations and physical property model of real gas, the compressor, pre-cooler and other components in the test loop are preliminarily designed by using the thermodynamic model of components. Since the operating conditions are in the vicinity of the critical point, when the operating conditions change slightly, the physical properties of the working fluid will change significantly, which might have a greater impact on the operating performance of the system. So the operating performance and the parameter changes of key nodes in the test loop under different operating conditions are calculated, which will provide theoretical guidance for the construction of subsequent experimental loops.

Numerical Approach for Real Gas Simulations: Part II — Flow Simulation for Supercritical CO2 Centrifugal Compressor

2017 ◽  
Author(s):  
Swati Saxena ◽  
Ramakrishna Mallina ◽  
Francisco Moraga ◽  
Douglas Hofer
Keyword(s):  
Critical Point ◽  
Centrifugal Compressor ◽  
Supercritical Co2 ◽  
Operating Conditions ◽  
Inlet Guide Vane ◽  
Thermodynamic Quantities ◽  
3D Flow ◽  
Real Gas ◽  
The Real ◽  
Operating Range

This paper is presented in two parts. Part I (Tabular fluid properties for real gas analysis) describes an approach to creating a tabular representation of the equation of state that is applicable to any fluid. This approach is applied to generating an accurate and robust tabular representation of the RefProp CO2 properties. Part II (this paper) presents numerical simulations of a low flow coefficient supercritical CO2 centrifugal compressor developed for a closed loop power cycle. The real gas tables presented in part I are used in these simulations. Three operating conditions are simulated near the CO2 critical point: normal day (85 bar, 35C), hot day (105 bar, 50 C) and cold day (70 bar, 20C) conditions. The compressor is a single stage overhung design with shrouded impeller, 155 mm impeller tip diameter and a vaneless diffuser. An axial variable inlet guide vane (IGV) is used to control the incoming swirl into the impeller. An in-house three-dimensional computational fluid dynamics (CFD) solver named TACOMA is used with real gas tables for the steady flow simulations. The equilibrium thermodynamic modeling is used in this study. The real gas effects are important in the desired impeller operating range. It is observed that both the operating range (minimum and maximum volumetric flow rate) and the pressure ratio across the impeller are dependent on the inlet conditions. The compressor has nearly 25% higher operating range on a hot day as compared to the normal day conditions. A condensation region is observed near the impeller leading edge which grows as the compressor operating point moves towards choke. The impeller chokes near the mid-chord due to lower speed of sound in the liquid-vapor region resulting in a sharp drop near the choke side of the speedline. This behavior is explained by analyzing the 3D flow field within the impeller and thermodynamic quantities along the streamline. The 3D flow analysis for the flow near the critical point provides useful insight for the designers to modify the current compressor design for higher efficiency.

CFD Simulation of a Supersonic Steam Ejector for Refrigeration Application

2016 ◽  
Author(s):  
Liju Su ◽  
Ramesh K. Agarwal
Keyword(s):  
Flow Field ◽  
Cfd Simulation ◽  
Fluid Pressure ◽  
Turbulence Models ◽  
Industrial Applications ◽  
Operating Conditions ◽  
Working Fluid ◽  
Entrainment Ratio ◽  
Ansys Fluent ◽  
Entrainment Velocity

Supersonic steam ejectors are widely used in many industrial applications, for example for refrigeration and desalination. The experimental evaluation of the flow field inside the ejector is relatively difficult and costly due to the occurrence of shock after the velocity of the steam reaches over the sonic level in the ejector. In this paper, numerical simulations are conducted to investigate the detailed flow field inside a supersonic steam (water vapor being the working fluid) ejector. The commercial computational fluid dynamics (CFD) flow solver ANSYS-Fluent and the mesh generation software ANSYS-ICEM are used to predict the steam performance during the mixing inside the ejector by employing two turbulence models, the k-ω SST and the k-ε realizable models. The computed results are validated against the experimental data. The effects of operating conditions on the efficiency of the ejector such as the primary fluid pressure and condenser pressure are studied to obtain a better understanding of the mixing process and entrainment. Velocity contours, pressure plots and shock region analyses provide a good understanding for optimization of the ejector performance, in particular how to increase the entrainment ratio.

A Comparison Study for Off-Design Performance Prediction of a Supercritical CO2 Compressor With Similitude Analysis

2019 ◽  
Author(s):  
Yongju Jeong ◽  
Seongmin Son ◽  
Seong kuk Cho ◽  
Seungjoon Baik ◽  
Jeong Ik Lee
Keyword(s):  
Critical Point ◽  
Supercritical Co2 ◽  
Power Plants ◽  
Cycle Performance ◽  
Working Fluid ◽  
Brayton Cycle ◽  
Power Cycle ◽  
Design Performance ◽  
Wide Range ◽  
Phase Fluid

Abstract Most of the power plants operating nowadays mainly have adopted a steam Rankine cycle or a gas Brayton cycle. To devise a better power conversion cycle, various approaches were taken by researchers and one of the examples is an S-CO2 (supercritical CO2) power cycle. Over the past decades, the S-CO2 power cycle was invented and studied. Eventually the cycle was successful for attracting attentions from a wide range of applications. Basically, an S-CO2 power cycle is a variation of a gas Brayton cycle. In contrast to the fact that an ordinary Brayton cycle operates with a gas phase fluid, the S-CO2 power cycle operates with a supercritical phase fluid, where temperatures and pressures of working fluid are above the critical point. Many advantages of S-CO2 power cycle are rooted from its novel characteristics. Particularly, a compressor in an S-CO2 power cycle operates near the critical point, where the compressibility is greatly reduced. Since the S-CO2 power cycle greatly benefits from the reduced compression work, an S-CO2 compressor prediction under off-design condition has a huge impact on overall cycle performance. When off-design operations of a power cycle are considered, the compressor performance needs to be specified. One of the approaches for a compressor off-design performance evaluation is to use the correction methods based on similitude analysis. However, there are several approaches for deriving the equivalent conditions but none of the approaches has been thoroughly examined for S-CO2 conditions based on data. The purpose of this paper is comparing these correction models to identify the best fitted approach, in order to predict a compressor off-design operation performance more accurately from limited amount of information. Each correction method was applied to two sets of data, SCEIL experiment data and 1D turbomachinery code off-design prediction code generated data, and evaluated in this paper.

Sign in / Sign up

Export Citation Format

Share Document