Size- and Temperature-Dependent Collision and Deposition Model for Micron-Sized Sand Particles

2019 ◽  
Vol 141 (3) ◽  
Author(s):  
Kuahai Yu ◽  
Danesh Tafti
Keyword(s):  
Gas Turbine ◽  
Recovery Process ◽  
Recovery Stage ◽  
Turbine Engine ◽  
Collision Model ◽  
Size Dependent ◽  
Plastic Stage ◽  
Sand Particles ◽  
Engine Components ◽  
The Impact

Sand ingestion and deposition in gas turbine engine components can lead to several operational hazards. This paper discusses a physics-based model for modeling the impact, deposition, and sticking of sand particles to surfaces. The collision model includes both normal and tangential components of impact. The normal collision model divides the impact process into three stages, the elastic stage, the elastic–plastic stage, and full plastic stage, and the recovery process is assumed to be fully elastic. The adhesion loss in the recovery stage is described using Timoshenko's model and Tsai's model, and shows that the two models are consistent under certain conditions. Plastic deformation losses of surface asperities are also considered for particle–wall collisions. The normal impact model is supplemented by an impulse-based tangential model, which includes both sliding and rolling frictions. Sand properties are characterized by size and temperature dependencies. The predicted coefficient of restitution (COR) of micron-sized sand particles is in very good agreement with experimental data at room temperature and at higher temperatures from 1073 K to 1340 K. The predicted COR decreases rapidly at temperatures above 1340 K. There is a strong interplay between the size-dependent properties of micron sand particles and the temperature dependency of yield stress on the collision and deposition characteristics. This is the first physics-based high temperature model including translation and rotation of micron-sized sand particles with sliding and rolling modes in the gas turbine literature.

Size and Temperature Dependent Deposition Model of Micro-Sized Sand Particles

2017 ◽  
Author(s):  
Kuahai Yu ◽  
Danesh Tafti
Keyword(s):  
Contact Force ◽  
Adhesion Force ◽  
Stokes Number ◽  
Experimental Result ◽  
Contact Radius ◽  
Recovery Stage ◽  
Line Force ◽  
Plastic Stage ◽  
Sand Particles ◽  
The Impact

Sand ingestion and deposition in gas turbine engine components can lead to several operational hazards. This paper discusses a physics based model for modeling the impact and deposition of sand particles. The collision model divides the impact process into three stages, the elastic stage, the elastic-plastic stage, and full plastic stage. The recovery stage is assumed to be fully elastic. The contact force, contact radius and work of contact force are conformed to the Hertzian theory, using “Young’s modulus similarity” rule to predict the recovery displacement. The adhesion loss in the recovery stage is considered using Dunn’s model, which describes the adhesion force as an idealized line force with the contact radius. The validation case of steel spherical particle impact on a glass surface with the maximum Stokes number of 10000, shows that the adhesion model with elastoplastic impact model describes the experimental result well. When the Stokes number is less than 12, the particle deposits on the surface. Sand properties are characterized by size and temperature dependencies. Model predictions for particle sizes ranging from 0.5 to 50 micron, impact velocities up to 80 m/s, and temperatures above 1300 K are given and discussed. It is shown that both size and temperature have an effect on the deposition characteristics.

Experimental and Numerical Correlation of Impact of Spherical Projectile for Damage Analysis of Aero Engine Component

2016 ◽  
Vol 66 (2) ◽  
pp. 193 ◽  
Author(s):  
Anuradha Nayak Majila ◽  
Rajeev Jain ◽  
Chandru Fernando D. ◽  
S. Ramachandra
Keyword(s):  
Finite Element ◽  
Gas Turbine ◽  
Gas Turbine Engine ◽  
Metallographic Analysis ◽  
Damage Analysis ◽  
Alloy Plate ◽  
Turbine Engine ◽  
Aero Engine ◽  
Engine Components ◽  
The Impact

<p>Studies the impact response of flat Titanium alloy plate against spherical projectile for damage analysis of aero engine components using experimental and finite element techniques. Compressed gas gun has been used to impart speed to spherical projectile at various impact velocities for damage studies. Crater dimensions (diameter and depth) obtained due to impact have been compared with finite element results using commercially available explicit finite element method code LS-DYNA. Strain hardening, high strain rate and thermal softening effect along with damage parameters have been considered using modified Johnson-Cook material model of LS-DYNA. Metallographic analysis has been performed on the indented specimen. This analysis is useful to study failure analysis of gas turbine engine components subjected to domestic object damage of gas turbine engine. </p><p> </p>

Flexible manufacturing in repair of gas turbine engine components

1992 ◽  
Author(s):  
KIRK D ◽  
ANDREW VAVRECK ◽  
ERIC LITTLE ◽  
LESLIE JOHNSON ◽  
BRETT SAYLOR
Keyword(s):  
Gas Turbine ◽  
Flexible Manufacturing ◽  
Gas Turbine Engine ◽  
Turbine Engine ◽  
Engine Components

Life assessment of a high temperature probe designed for performance evaluation and health monitoring of an aero gas turbine engine

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Benny George ◽  
Nagalingam Muthuveerappan
Keyword(s):  
Performance Evaluation ◽  
Gas Turbine ◽  
Health Monitoring ◽  
Gas Turbine Engine ◽  
Life Assessment ◽  
Exhaust Gas ◽  
Cycle Fatigue ◽  
Creep Life ◽  
Turbine Engine ◽  
Engine Components

AbstractTemperature probes of different designs were widely used in aero gas turbine engines for measurement of air and gas temperatures at various locations starting from inlet of fan to exhaust gas from the nozzle. Exhaust Gas Temperature (EGT) downstream of low pressure turbine is one of the key parameters in performance evaluation and digital engine control. The paper presents a holistic approach towards life assessment of a high temperature probe housing thermocouple sensors designed to measure EGT in an aero gas turbine engine. Stress and vibration analysis were carried out from mechanical integrity point of view and the same was evaluated in rig and on the engine. Application of 500 g load concept to clear the probe design was evolved. The design showed strength margin of more than 20% in terms of stress and vibratory loads. Coffin Manson criteria, Larsen Miller Parameter (LMP) were used to assess the Low Cycle Fatigue (LCF) and creep life while Goodman criteria was used to assess High Cycle Fatigue (HCF) margin. LCF and HCF are fatigue related damage from high frequency vibrations of engine components and from ground-air-ground engine cycles (zero-max-zero) respectively and both are of critical importance for ensuring structural integrity of engine components. The life estimation showed LCF life of more than 4000 mission reference cycles, infinite HCF life and well above 2000 h of creep life. This work had become an integral part of the health monitoring, performance evaluation as well as control system of the aero gas turbine engine.

Life assessment of a high temperature probe designed for performance evaluation and health monitoring of an aero gas turbine engine

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Benny George ◽  
Nagalingam Muthuveerappan
Keyword(s):  
Performance Evaluation ◽  
Gas Turbine ◽  
Health Monitoring ◽  
Gas Turbine Engine ◽  
Life Assessment ◽  
Exhaust Gas ◽  
Cycle Fatigue ◽  
Creep Life ◽  
Turbine Engine ◽  
Engine Components

Abstract Temperature probes of different designs were widely used in aero gas turbine engines for measurement of air and gas temperatures at various locations starting from inlet of fan to exhaust gas from the nozzle. Exhaust Gas Temperature (EGT) downstream of low pressure turbine is one of the key parameters in performance evaluation and digital engine control. The paper presents a holistic approach towards life assessment of a high temperature probe housing thermocouple sensors designed to measure EGT in an aero gas turbine engine. Stress and vibration analysis were carried out from mechanical integrity point of view and the same was evaluated in rig and on the engine. Application of 500 g load concept to clear the probe design was evolved. The design showed strength margin of more than 20% in terms of stress and vibratory loads. Coffin Manson criteria, Larsen Miller Parameter (LMP) were used to assess the Low Cycle Fatigue (LCF) and creep life while Goodman criteria was used to assess High Cycle Fatigue (HCF) margin. LCF and HCF are fatigue related damage from high frequency vibrations of engine components and from ground-air-ground engine cycles (zero-max-zero) respectively and both are of critical importance for ensuring structural integrity of engine components. The life estimation showed LCF life of more than 4000 mission reference cycles, infinite HCF life and well above 2000 h of creep life. This work had become an integral part of the health monitoring, performance evaluation as well as control system of the aero gas turbine engine.

Diagnosis of Turbine Engine Transient Performance With Model-Based Parameter Estimation Techniques

1994 ◽  
Author(s):  
Jeff W. Bird ◽  
Howard M. Schwartz
Keyword(s):  
Gas Turbine ◽  
Test Data ◽  
Physical Models ◽  
Turbine Engine ◽  
Robustness To Noise ◽  
Linear Effects ◽  
Diagnostic Capabilities ◽  
Engine Components ◽  
And Control ◽  
Parameter Estimation Techniques

This review surveys knowledge needed to develop an improved method of modelling the dynamics of gas turbine performance for fault diagnosis applications. Aerothermodynamic and control models of gas turbine processes are examined as complementary to models derived directly from test data. Extensive, often proprietary data are required for physical models of components, while system identification (SI) methods need data from specially-designed tests. Current methods are limited in: tuning models to test data, non-linear effects, component descriptions in SI models, robustness to noise, and inclusion of control systems and actuators. Conclusions are drawn that SI models could be formulated, with parameters which describe explicitly the functions of key engine components, to offer improved diagnostic capabilities.

Account of Film Turbulence for Predicting Film Cooling Effectiveness in Gas Turbine Combustors

1979 ◽  
Author(s):  
G. J. Sturgess
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Cooling Effectiveness ◽  
Turbine Engine ◽  
Film Cooling Effectiveness ◽  
Wide Range ◽  
Engine Combustion ◽  
Turbulence Effects ◽  
The Impact ◽  
Combustor Liner

The paper deals with a small but important part of the overall gas turbine engine combustion system and continues earlier published work on turbulence effects in film cooling to cover the case of film turbulence. Film cooling of the gas turbine combustor liner imposes certain geometric limitations on the coolant injection device. The impact of practical film injection geometry on the cooling is one of increased rates of film decay when compared to the performance from idealized injection geometries at similar injection conditions. It is important to combustor durability and life estimation to be able to predict accurately the performance obtainable from a given practical slot. The coolant film is modeled as three distinct regions, and the effects of injection slot geometry on the development of each region are described in terms of film turbulence intensity and initial circumferential non-uniformity of the injected coolant. The concept of the well-designed slot is introduced and film effectiveness is shown to be dependent on it. Only slots which can be described as well-designed are of interest in practical equipment design. A prediction procedure is provided for well-designed slots which describes growth of the film downstream of the first of the three film regions. Comparisons of predictions with measured data are made for several very different well-designed slots over a relatively wide range of injection conditions, and good agreement is shown.

An Integrated Approach for Gas Turbine Engine Simulation

2000 ◽  
Author(s):  
Zhiwu Xie ◽  
Ming Su ◽  
Shilie Weng
Keyword(s):  
Gas Turbine ◽  
Local Area Network ◽  
Integrated Approach ◽  
Local Area ◽  
Gas Turbine Engine ◽  
Future Research ◽  
Area Network ◽  
Turbine Engine ◽  
Engine Simulation ◽  
Engine Components

Abstract The static and transient performance of a gas turbine engine is determined by both the characteristics of the engine components and their interactions. This paper presents a generalized simulation framework that enables the integration of different component and system simulation codes. The concept of engine simulation integration and its implementation model is described. The model is designed as an object-oriented system, in which various simulation tasks are assigned to individual software components that interact with each other. A new design rationale called “message-based modeling” and its resulting class structure is presented and analyzed. The object model is implemented within a heterogeneous network environment. To demonstrate its flexibility, the codes that deal with different engine components are separately programmed on different computers running various operating systems. These components communicate with each other via a CORBA compliant ORB, which simulates the overall performance of an engine system. The resulting system has been tested on a Local Area Network (LAN) to simulate the transient response of a three-shaft gas turbine engine, subject to small fuel step perturbations. The simulation results for various network configurations are presented. It is evident that in contrast to a standalone computer simulation, the distributed implementation requires much longer simulation time. This difference of simulation efficiency is analyzed and explained. The limitations of this endeavor, along with some future research topics, are also reported in this paper.

Sign in / Sign up

Export Citation Format

Share Document