Fingertip-Sized Pressure Sensor for Luer Taper of Three-Way Stopcock in Liquid Channel

2019 ◽  
Vol 13 (3) ◽  
Author(s):  
Kei Takenaka ◽  
Shigenori Togashi ◽  
Atsushi Kazama ◽  
Kentaro Miyajima ◽  
Takashi Nagano
Keyword(s):  
Pressure Sensor ◽  
Three Dimensional ◽  
Strain Sensor ◽  
Variable Pressure ◽  
Silicone Resin ◽  
3D Printer ◽  
Double Pipe ◽  
Fitting Part ◽  
Liquid Channel ◽  
Semiconductor Strain

We developed an easily attachable fingertip-sized pressure sensor (FSPS) for a three-way stopcock in a liquid channel of a heart–lung machine. The FSPS has a double-pipe structure with a semispherical soft film cap on the pointed end and a diaphragm semiconductor strain sensor on the other end. An enclosed space of variable volume covered with the soft film cap prevents the semiconductor strain sensor from coming into direct contact with blood, and the double-pipe structure decreases the strain on the strain sensor when inserting the FSPS into the female-fitting part of the luer taper. It is difficult to fabricate a very fine double-pipe structure by cutting or injection molding. Instead, we fabricated it by using a three-dimensional (3D) printer. Moreover, it is difficult to fabricate a semispherical soft film cap with a 3D printer, so we fabricated it with a resin casting method using silicone resin. Experiments on the FSPS using a variable pressure liquid channel showed that it is not affected by inserting it into the female-fitting part of the luer taper and that it can accurately measure pressure in a liquid channel within a pressure range from 0 to 100 kPa.

Development of Corrosion-Resistant Pressure Sensor with Semiconductor Strain Sensor

2018 ◽  
Vol 203 (2) ◽  
pp. 58-65
Author(s):  
KENGO SUZUKI ◽  
HIROYUKI OOTA ◽  
TAKAHIRO UMEYAMA
Keyword(s):  
Pressure Sensor ◽  
Strain Sensor ◽  
Corrosion Resistant ◽  
Semiconductor Strain

CREATING AN OVER PRESSURE SENSOR METRAN-43 DI WITH THE KOMPAS-3D PROGRAM

2019 ◽  
Author(s):  
Roman Grishin ◽  
Dmitriy Nesnov
Keyword(s):  
Pressure Sensor ◽  
Three Dimensional ◽  
Dimensional Model ◽  
Three Dimensional Model ◽  
Graphic Editor ◽  
The Creation ◽  
Photorealistic Images

This article describes the creation of a three-dimensional model of the overpressure sensor Metran-43 using the graphic editor COMPASS-v17, as well as photorealistic images in the program Artisan Rendering and created animation disassembly-Assembly of the device, allowing you to see the internal components of the product.

scholarly journals Efficient 3D printing via photooxidation of ketocoumarin based photopolymerization

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Xiaoyu Zhao ◽  
Ye Zhao ◽  
Ming-De Li ◽  
Zhong’an Li ◽  
Haiyan Peng ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
3D Printing ◽  
Visible Light ◽  
Light Exposure ◽  
Three Dimensional ◽  
3D Printer ◽  
Light Penetration ◽  
Viable Solution

AbstractPhotopolymerization-based three-dimensional (3D) printing can enable customized manufacturing that is difficult to achieve through other traditional means. Nevertheless, it remains challenging to achieve efficient 3D printing due to the compromise between print speed and resolution. Herein, we report an efficient 3D printing approach based on the photooxidation of ketocoumarin that functions as the photosensitizer during photopolymerization, which can simultaneously deliver high print speed (5.1 cm h−1) and high print resolution (23 μm) on a common 3D printer. Mechanistically, the initiating radical and deethylated ketocoumarin are both generated upon visible light exposure, with the former giving rise to rapid photopolymerization and high print speed while the latter ensuring high print resolution by confining the light penetration. By comparison, the printed feature is hard to identify when the ketocoumarin encounters photoreduction due to the increased lateral photopolymerization. The proposed approach here provides a viable solution towards efficient additive manufacturing by controlling the photoreaction of photosensitizers during photopolymerization.

scholarly journals A flexible and highly sensitive pressure sensor based on three-dimensional electrospun carbon nanofibers

RSC Advances ◽  
2021 ◽  
Vol 11 (23) ◽  
pp. 13898-13905
Author(s):  
Chuan Cai ◽  
He Gong ◽  
Weiping Li ◽  
Feng Gao ◽  
Qiushi Jiang ◽  
...  
Keyword(s):  
Carbon Nanofibers ◽  
Pressure Sensor ◽  
Carbon Nanofiber ◽  
Three Dimensional ◽  
High Sensitivity ◽  
Highly Sensitive ◽  
Sensitive Pressure

A three-dimensional electrospun carbon nanofiber network was used to measure press strains with high sensitivity.

scholarly journals Supercritical Impregnation of PLA Filaments with Mango Leaf Extract to Manufacture Functionalized Biomedical Devices by 3D Printing

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2125
Author(s):  
José María Rosales ◽  
Cristina Cejudo ◽  
Lidia Verano ◽  
Lourdes Casas ◽  
Casimiro Mantell ◽  
...  
Keyword(s):  
Antioxidant Activity ◽  
3D Printing ◽  
Polylactic Acid ◽  
Leaf Extract ◽  
Three Dimensional ◽  
3D Printer ◽  
Pharmacological Properties ◽  
Bioactive Properties ◽  
Supercritical Impregnation ◽  
Mango Leaves

Polylactic Acid (PLA) filaments impregnated with ethanolic mango leaves extract (MLE) with pharmacological properties were obtained by supercritical impregnation. The effects of pressure, temperature and amount of extract on the response variables, i.e., swelling, extract loading and bioactivity of the PLA filaments, were determined. The analysis of the filaments biocapacities revealed that impregnated PLA filaments showed 11.07% antidenaturant capacity and 88.13% antioxidant activity, which after a 9-day incubation shifted to 30.10% and 9.90%, respectively. Subsequently, the same tests were conducted on printed samples. Before their incubation, the printed samples showed 79.09% antioxidant activity and no antidenaturant capacity was detected. However, after their incubation, the antioxidant activity went down to only 2.50%, while the antidenaturant capacity raised up to 23.50%. The persistence of the bioactive properties after printing opens the possibility of using the functionalized PLA filaments as the feed for a three-dimensional (3D) printer.

scholarly journals Three-Dimensional Arterial Pulse Signal Acquisition in Time Domain Using Flexible Pressure-Sensor Dense Arrays

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 569
Author(s):  
Jianzhong Chen ◽  
Ke Sun ◽  
Rong Zheng ◽  
Yi Sun ◽  
Heng Yang ◽  
...  
Keyword(s):  
Radial Artery ◽  
Pressure Sensor ◽  
Pulse Width ◽  
Printed Circuit Boards ◽  
Color Doppler ◽  
Three Dimensional ◽  
Pressure Sensors ◽  
Sensor Arrays ◽  
Signal Acquisition ◽  
Dynamic Pulse

In this study, we developed a radial artery pulse acquisition system based on finger-worn dense pressure sensor arrays to enable three-dimensional pulse signals acquisition. The finger-worn dense pressure-sensor arrays were fabricated by packaging 18 ultra-small MEMS pressure sensors (0.4 mm × 0.4 mm × 0.2 mm each) with a pitch of 0.65 mm on flexible printed circuit boards. Pulse signals are measured and recorded simultaneously when traditional Chinese medicine practitioners wear the arrays on the fingers while palpating the radial pulse. Given that the pitches are much smaller than the diameter of the human radial artery, three-dimensional pulse envelope images can be measured with the system, as can the width and the dynamic width of the pulse signals. Furthermore, the array has an effective span of 11.6 mm—3–5 times the diameter of the radial artery—which enables easy and accurate positioning of the sensor array on the radial artery. This study also outlines proposed methods for measuring the pulse width and dynamic pulse width. The dynamic pulse widths of three volunteers were measured, and the dynamic pulse width measurements were consistent with those obtained by color Doppler ultrasound. The pulse wave velocity can also be measured with the system by measuring the pulse transit time between the pulse signals at the brachial and radial arteries using the finger-worn sensor arrays.

scholarly journals Low-Cost Customized Cranioplasty with Polymethyl Methacrylate Using 3D Printer Generated Mold: An Institutional Experience and Review of Literature

2021 ◽  
Author(s):  
Ankit Chaudhary ◽  
Virendra Deo Sinha ◽  
Sanjeev Chopra ◽  
Jitendra Shekhawat ◽  
Gaurav Jain
Keyword(s):  
Polymethyl Methacrylate ◽  
Bone Fractures ◽  
Low Cost ◽  
Operating Time ◽  
Three Dimensional ◽  
Wound Dehiscence ◽  
3D Printer ◽  
Skull Defects ◽  
Aesthetic Appearance ◽  
The Mean

Abstract Background Cranioplasty is performed to repair skull defects and to restore normal skull anatomy. Optimal reconstruction remains a topic of debate. Autologous bone flap is the standard option but it may not be available due to traumatic bone fractures, bone infection, and resorption. The authors present their experience with prefabrication of precise and low-cost polymethyl methacrylate (PMMA) mold using three-dimensional (3D) digital printing. Methods A total of 30 patients underwent cranioplasty between March 2017 and September 2019 at Sawai Man Singh Medical College Jaipur, India. Preoperative data included diagnosis for which decompressive craniectomy was done and Glasgow coma scale score. Intraoperative data included operating time. Postoperative data included cosmetic outcome in the form of cranial contour and margins, complications such as infection, seroma, implant failure, wound dehiscence, and hematoma. Results Patient age at cranioplasty ranged from 12 to 63 years with a mean age of 36.7 years. The mean operating time was 151.6 minutes (range 130–190 minutes). The mean follow-up period was 8 months (range 6–13 months). Postoperative wound dehiscence developed in one case (3.3%). Cranial contour and approximation of the margins were excellent and aesthetic appearance improved in all patients. Conclusion Low-cost PMMA implant made by digital 3D printer mold is associated with reconstruction of the deformed skull contour giving satisfactory results to the patient and his family members, at a low cost compared with other commercially available implants. This technique could be a breakthrough in cranioplasty.

Research on the printing error of tilted vertical beams in delta-robot 3D printers

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Yuezong Wang ◽  
Jinghui Liu ◽  
Mengfei Guo ◽  
LiuQIan Wang
Keyword(s):  
3D Printing ◽  
Kinematic Model ◽  
Three Dimensional ◽  
3D Printer ◽  
Simulation Approach ◽  
Content Type ◽  
Printing Quality ◽  
Delta Robot ◽  
Error Generation ◽  
Error Simulation

Purpose A three-dimensional (3D) printing error simulation approach is proposed to analyze the influence of tilted vertical beams on the 3D printing accuracy. The purpose of this study is to analyze the influence of such errors on printing accuracy and printing quality for delta-robot 3D printer. Design/methodology/approach First, the kinematic model of a delta-robot 3D printer with an ideal geometric structure is proposed by using vector analysis. Then, the normal kinematic model of a nonideal delta-robot 3D robot with tilted vertical beams is derived based on the above ideal kinematic model. Finally, a 3D printing error simulation approach is proposed to analyze the influence of tilted vertical beams on the 3D printing accuracy. Findings The results show that tilted vertical beams can indeed cause 3D printing errors and further influence the 3D printing quality of the final products and that the 3D printing errors of tilted vertical beams are related to the rotation angles of the tilted vertical beams. The larger the rotation angles of the tilted vertical beams are, the greater the geometric deformations of the printed structures. Originality/value Three vertical beams and six horizontal beams constitute the supporting parts of the frame of a delta-robot 3D printer. In this paper, the orientations of tilted vertical beams are shown to have a significant influence on 3D printing accuracy. However, the effect of tilted vertical beams on 3D printing accuracy is difficult to capture by instruments. To reveal the 3D printing error mechanisms under the condition of tilted vertical beams, the error generation mechanism and the quantitative influence of tilted vertical beams on 3D printing accuracy are studied by simulating the parallel motion mechanism of a delta-robot 3D printer with tilted vertical beams.

scholarly journals Implementing a 3D printing service in a biomedical library

2017 ◽  
Vol 105 (1) ◽  
Author(s):  
Verma Walker, MLIS
Keyword(s):  
Problem Solving ◽  
3D Printing ◽  
3D Modeling ◽  
Three Dimensional ◽  
National Institutes Of Health ◽  
3D Printer ◽  
Service Model ◽  
Steep Learning Curve ◽  
3D Printers ◽  
Creative Problem

Three-dimensional (3D) printing is opening new opportunities in biomedicine by enabling creative problem solving, faster prototyping of ideas, advances in tissue engineering, and customized patient solutions. The National Institutes of Health (NIH) Library purchased a Makerbot Replicator 2 3D printer to give scientists a chance to try out this technology. To launch the service, the library offered training, conducted a survey on service model preferences, and tracked usage and class attendance. 3D printing was very popular, with new lab equipment prototypes being the most common model type. Most survey respondents indicated they would use the service again and be willing to pay for models. There was high interest in training for 3D modeling, which has a steep learning curve. 3D printers also require significant care and repairs. NIH scientists are using 3D printing to improve their research, and it is opening new avenues for problem solving in labs. Several scientists found the 3D printer so helpful they bought one for their labs. Having a printer in a central and open location like a library can help scientists, doctors, and students learn how to use this technology in their work.

Sign in / Sign up

Export Citation Format

Share Document