Numerical Simulation of a Naturally Aspirated Natural Gas/Diesel RCCI Engine for Investigating the Effects of Injection Timing on the Combustion and Emissions

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
Amir Hossein Fakhari ◽  
Rouzbeh Shafaghat ◽  
Omid Jahanian
Keyword(s):  
Natural Gas ◽  
Fuel Mixture ◽  
Injection Timing ◽  
Reactivity Controlled Compression Ignition ◽  
Piston Bowl ◽  
Start Of Injection ◽  
Performance And Emissions ◽  
The Difference ◽  
The Impact ◽  
Co Emission

Abstract The start of injection (SOI) timing has a significant effect on increasing the homogeneity of the air–fuel mixture in an reactivity controlled compression ignition (RCCI) engine. In this paper, the impact of the SOI timing from 14 deg to 74 deg before top dead center (bTDC) and different inlet valve closing (IVC) temperatures on natural gas/diesel RCCI performance and emissions have been studied. Also, the simulations carried out by avl fire which is coupled with chemical kinetics. The results showed that in the SOIs of 14 deg, 24 deg, and 34 deg bTDC, the fuel is sprayed into the piston bowl; however, in the SOI of 44 deg bTDC, the fuel collides the bowl rim edge, because of the downward movement of the piston. With the advancement of diesel SOI timing from 14 deg to 74 deg bTDC, two different combustion trends can be observed. However, this advancement leads to a lower CO emission, but it raises the CO2 emission level. Although the pressure is a primary parameter for NOx emission, the difference between the trends of NOx and pressure plots indicates that different factors affect the NOx production and also increase the IVC temperature, and raises the in-cylinder pressure, heat release rate, NOx and CO2 emissions, while it reduces the CO emission.

scholarly journals Experimental Study of the Effect of Start of Injection and Blend Ratio on Single Fuel Reformate RCCI

2020 ◽  
Vol 142 (8) ◽  
Author(s):  
Deivanayagam Hariharan ◽  
Brian Gainey ◽  
Ziming Yan ◽  
Sotirios Mamalis ◽  
Benjamin Lawler
Keyword(s):  
Oxygen Deficiency ◽  
Fuel Mixture ◽  
Combustion Efficiency ◽  
High Reactivity ◽  
Inert Gases ◽  
Injection Timing ◽  
Indicated Mean Effective Pressure ◽  
Start Of Injection ◽  
The Difference ◽  
Blend Ratios

Abstract A new concept of single fuel reactivity-controlled compression ignition (RCCI) has been proposed through the catalytic partial oxidation (CPOX) reformation of diesel fuel. The reformed fuel mixture is then used as the low reactivity fuel and diesel itself is used as the high reactivity fuel. In this paper, two reformate mixtures from the reformation of diesel were selected for further analysis. Each reformate fuel mixture contained a significant fraction of inert gases (89% and 81%). The effects of the difference in the molar concentrations of the reformate mixtures were studied by experimenting with diesel as the direct injected fuel in RCCI over a varying start of injection timings and different blend ratios (i.e., the fraction of low and high reactivity fuels). The reformate mixture with the lower inert gas concentration had earlier combustion phasing and shorter combustion duration at any given diesel start of injection timing. The higher reactivity separation between reformate mixture and diesel, compared with gasoline and diesel, causes the combustion phasing of reformate-diesel RCCI to be more sensitive to the start of injection timing. The maximum combustion efficiency was found at a CA50 before top dead center (TDC), whereas the maximum thermal efficiency occurs at a CA50 after TDC. The range of energy-based blend ratios in which reformate-diesel RCCI is possible is between 25% and 45%, limited by ringing intensity (RI) at the low limit of blend ratios, and coefficient of variance (COV) of net indicated mean effective pressure (IMEPn) and combustion efficiency at the high limit. Intake boosting becomes necessary due to the oxygen deficiency caused by the low energy density of the reformate mixtures as it displaces intake air.

scholarly journals An Experimental Investigation on the Influence of Port Injection at Valve on Combustion and Emission Characteristics of B5/Biogas RCCI Engine

2020 ◽  
Vol 10 (2) ◽  
pp. 452
Author(s):  
Ibrahim B. Dalha ◽  
Mior A. Said ◽  
Zainal A. Abdul Karim ◽  
Salah E. Mohammed
Keyword(s):  
Fuel Mixture ◽  
Injection Timing ◽  
Compression Ignition ◽  
Reactivity Controlled Compression Ignition ◽  
Indicated Mean Effective Pressure ◽  
Unburned Hydrocarbon ◽  
Crank Angle ◽  
Slow Combustion ◽  
Low Load ◽  
Co Emission

High unburned hydrocarbon (UHC) and carbon monoxide (CO) emissions, on account of the premixed air-fuel mixture entering the crevices and pre-mature combustion, are setbacks to reactivity-controlled compression ignition (RCCI) combustion at a low load. The influence of direct-injected B5 and port injection of biogas at the intake valve was, experimentally, examined in the RCCI mode. The port injection at the valve was to elevate the temperature at low load and eliminate premixing for reduced pre-mature combustion and fuel entering the crevices. An advanced injection timing of 21° crank angle before top dead centre and fraction of 50% each of the fuels, were maintained at speeds of 1600, 1800 and 2000 rpm and varied the load from 4.5 to 6.5 bar indicated mean effective pressure (IMEP). The result shows slow combustion as the load increases with the highest indicated thermal efficiency of 36.33% at 5.5 bar IMEP. The carbon dioxide and nitrogen oxides emissions increased, but UHC emission decreased, significantly, as the load increases. However, CO emission rose from 4.5 to 5.5 bar IMEP, then reduced as the load increases. The use of these fuels and biogas injection at the valve were capable of averagely reducing the persistent challenge of the CO and UHC emissions, by 20.33% and 10% respectively, compared to the conventional premixed mode.

scholarly journals Experimental Study of the Effect of Start of Injection and Blend Ratio on Single Fuel Reformate RCCI

2019 ◽  
Author(s):  
Deivanayagam Hariharan ◽  
Brian Gainey ◽  
Ziming Yan ◽  
Sotirios Mamalis ◽  
Benjamin Lawler
Keyword(s):  
Oxygen Deficiency ◽  
Fuel Mixture ◽  
Combustion Efficiency ◽  
High Reactivity ◽  
Inert Gases ◽  
Injection Timing ◽  
Start Of Injection ◽  
Combustion Duration ◽  
The Difference ◽  
Blend Ratios

Abstract A new concept of single-fuel RCCI has been proposed through the catalytic partial oxidation reformation of diesel fuel. The reformed fuel mixture is then used as the low reactivity fuel and diesel itself is used as the high reactivity fuel. In this paper, two selected reformates mixture from the reformation of diesel were selected for further analysis. Each reformate fuel mixture contained a significant fraction of inert gases (89% and 81%). The effects of the difference in the molar concentrations of the reformate mixtures were studied by experimenting with diesel as the direct injected fuel in RCCI over a varying start of injection timings and different blend ratios (i.e., the fraction of low and high reactivities fuels). The reformate mixture with the lower inert gas concentration had earlier combustion phasing and shorter combustion duration at any given diesel start of injection timing. The higher reactivity separation between reformate mixture and diesel, compared with gasoline and diesel, causes the combustion phasing of reformate-diesel RCCI to be more sensitive to the start of injection timing. The maximum combustion efficiency was found at a CA50 before TDC, whereas the maximum thermal efficiency occurs at a CA50 after TDC. The range of energy-based blend ratios in which reformate-diesel RCCI is possible is between 25% and 45%, limited by ringing intensity (RI) at the low limit of blend ratios, and COV of IMEP and combustion efficiency at the high limit. Intake boosting becomes necessary due to the oxygen deficiency caused by the low energy density of the reformate mixtures as it displaces intake air.

Experimental Investigation of the Performance of a Micro Gas Turbine Fueled With Mixtures of Natural Gas and Biogas

2013 ◽  
Author(s):  
Homam Nikpey ◽  
Mohsen Assadi ◽  
Peter Breuhaus
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Co2 Emissions ◽  
Fuel Mixture ◽  
Combined Heat And Power ◽  
Test Rig ◽  
Heating Value ◽  
Micro Gas Turbine ◽  
Fuel Mixtures ◽  
The Impact

Previously published studies have addressed modifications to the engines when operating with biogas, i.e. a low heating value (LHV) fuel. This study focuses on mapping out the possible biogas share in a fuel mixture of biogas and natural gas in micro combined heat and power (CHP) installations without any engine modifications. This contributes to a reduction in CO2 emissions from existing CHP installations and makes it possible to avoid a costly upgrade of biogas to the natural gas quality as well as engine modifications. Moreover, this approach allows the use of natural gas as a “fallback” solution in the case of eventual variations of the biogas composition and or shortage of biogas, providing improved availability. In this study, the performance of a commercial 100kW micro gas turbine (MGT) is experimentally evaluated when fed by varying mixtures of natural gas and biogas. The MGT is equipped with additional instrumentation, and a gas mixing station is used to supply the demanded fuel mixtures from zero biogas to maximum possible level by diluting natural gas with CO2. A typical biogas composition with 0.6 CH4 and 0.4 CO2 (in mole fraction) was used as reference, and corresponding biogas content in the supplied mixtures was computed. The performance changes due to increased biogas share were studied and compared with the purely natural gas fired engine. This paper presents the test rig setup used for the experimental activities and reports results, demonstrating the impact of burning a mixture of biogas and natural gas on the performance of the MGT. Comparing with when only natural gas was fired in the engine, the electrical efficiency was almost unchanged and no significant changes in operating parameters were observed. It was also shown that burning a mixture of natural gas and biogas contributes to a significant reduction in CO2 emissions from the plant.

Influence of the Spatial and Temporal Interaction Between Diesel Pilot and Directly Injected Natural Gas Jet on Ignition and Combustion Characteristics

2017 ◽  
Author(s):  
Georg Fink ◽  
Michael Jud ◽  
Thomas Sattelmayer
Keyword(s):  
Natural Gas ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Combustion Process ◽  
Gas Jet ◽  
Injection Timing ◽  
Release Rates ◽  
Temporal Interaction ◽  
The Impact

In this paper, pilot-ignited high pressure dual-fuel (HPDF) combustion of a natural gas jet is investigated on a fundamental basis by applying two separate single-hole injectors to a rapid compression expansion machine (RCEM). A Shadowgraphy system is used for optical observations, and the combustion progress is assessed in terms of heat release rates. The experiments focus on the combined influence of injection timing and geometrical jet arrangement on the jet interaction and the impact on the combustion process. In a first step, the operational range for successful pilot self-ignition and transition to natural gas jet combustion is determined, and the restricting phenomena are identified by analyzing the shadowgraph images. Within this range, the combustion process is assessed by evaluation of ignition delays and heat release rates. Strong interaction is found to delay or even prohibit pilot ignition, while it facilitates a fast and stable onset of the gas jet combustion. Furthermore, it is shown that the heat release rate is governed by the time of ignition with respect to the start of natural gas injection — as this parameter defines the level of premixing. Evaluation of the time of gas jet ignition within the operability map can therefore directly link a certain spatial and temporal interaction to the resulting heat release characteristics. It is finally shown that controlling the heat release rate through injection timing variation is limited for a certain angle between the two jets.

Influence of the Spatial and Temporal Interaction Between Diesel Pilot and Directly Injected Natural Gas Jet on Ignition and Combustion Characteristics

2018 ◽  
Vol 140 (10) ◽  
Author(s):  
Georg Fink ◽  
Michael Jud ◽  
Thomas Sattelmayer
Keyword(s):  
Natural Gas ◽  
Heat Release ◽  
Combustion Process ◽  
Optical Observations ◽  
Gas Jet ◽  
Injection Timing ◽  
Ignition And Combustion ◽  
Temporal Interaction ◽  
Operational Range ◽  
The Impact

In this paper, pilot-ignited high pressure dual-fuel combustion of a natural gas jet is investigated on a fundamental basis by applying two separate single-hole injectors to a rapid compression expansion machine (RCEM). A Shadowgraphy system is used for optical observations, and the combustion progress is assessed in terms of heat release rates (HRRs). The experiments focus on the combined influence of injection timing and geometrical jet arrangement on the jet interaction and the impact on the combustion process. In a first step, the operational range for successful pilot self-ignition and transition to natural gas jet combustion is determined, and the restricting phenomena are identified by analyzing the shadowgraph images. Within this range, the combustion process is assessed by evaluation of ignition delays and HRRs. Strong interaction is found to delay or even prohibit pilot ignition, while it facilitates a fast and stable onset of the gas jet combustion. Furthermore, it is shown that the HRR is governed by the time of ignition with respect to the start of natural gas injection—as this parameter defines the level of premixing. Evaluation of the time of gas jet ignition within the operability map can therefore directly link a certain spatial and temporal interaction to the resulting heat release characteristics. It is finally shown that controlling the HRR through injection timing variation is limited for a certain angle between the two jets.

Sign in / Sign up

Export Citation Format

Share Document