Design for Sustained and Occasional Loads

2021 ◽  
pp. 59-64
Author(s):  
Charles Becht
Keyword(s):  
Internal Pressure ◽  
Wall Thickness ◽  
Axial Direction ◽  
Longitudinal Stress

The wall thickness of pipe is nearly always selected based on the thickness required for internal pressure and allowances. The piping is then supported sufficiently such that the longitudinal stress (the stress in the axial direction of the pipe) is within Code limits and deflection is w ithin acceptable limits.

Ratcheting assessment of corroded elbow pipes subjected to internal pressure and cyclic bending moment

2021 ◽  
pp. 030932472198989
Author(s):  
Ali Salehi ◽  
Armin Rahmatfam ◽  
Mohammad Zehsaz
Keyword(s):  
Growth Rate ◽  
Stainless Steel ◽  
Internal Pressure ◽  
Bending Moment ◽  
Axial Direction ◽  
Hoop Strain ◽  
Cyclic Bending ◽  
High Fatigue ◽  
The Impact ◽  
Cyclic Bending Moment

The present study aimed to study ratcheting strains of corroded stainless steel 304LN elbow pipes subjected to internal pressure and cyclic bending moment. To this aim, spherical and cubical shapes corrosion are applied at two depths of 1 mm and 2 mm in the critical points of elbow pipe such as symmetry sites at intrados, extrados, and crown positions. Then, a Duplex 2205 stainless steel elbow pipe is considered as an alternative to studying the impact of the pipe materials, due to its high corrosion resistance and strength, toughness, and most importantly, the high fatigue strength and other mechanical properties than stainless steel 304LN. In order to perform numerical analyzes, the hardening coefficients of the materials were calculated. The results highlight a significant relationship between the destructive effects of corrosion and the depth and shape of corrosion, so that as corrosion increases, the resulting destructive effects increases as well, also, the ratcheting strains in cubic corrosions have a higher growth rate than spherical corrosions. In addition, the growth rate of the ratcheting strains in the hoop direction is much higher across the studied sample than the axial direction. The highest growth rate of hoop strain was observed at crown and the highest growth rate of axial strains occurred at intrados position. Altogether, Duplex 2205 material has a better performance than SS 304LN.

Circumferential Creep Strain of Cylinders Subjected to Internal Pressure: A Comparison of the Theories of Johnson and Bailey

1966 ◽  
Vol 8 (1) ◽  
pp. 22-26 ◽  
Author(s):  
E. C. Larke ◽  
R. J. Parker
Keyword(s):  
Internal Pressure ◽  
Creep Strain ◽  
Wall Thickness ◽  
Circumferential Strain ◽  
Axial Stress ◽  
Integration Procedure ◽  
Graphical Integration ◽  
Simple Equations

When considering the creep of cylinders subjected to internal pressure, the theory of Johnson et al. takes into account progressive changes of radial, circumferential and axial stress at any point in the wall thickness. This approach differs from that put forward by Bailey, who assumed that these stresses remained constant with time. The present paper summarizes an examination of both theories, with particular reference to outside and bore diameters, and presents simple equations which enable circumferential strain to be calculated without using the complex graphical integration procedure suggested by Johnson. Furthermore, it is demonstrated that these equations are mathematically identical with those derived by Bailey.

Elastic-plastic bending of the pipeline under combined loading

2021 ◽  
pp. 372-377
Author(s):  
Виктор Миронович Варшицкий ◽  
Евгений Павлович Студёнов ◽  
Олег Александрович Козырев ◽  
Эльдар Намикович Фигаров
Keyword(s):  
Internal Pressure ◽  
Limit State ◽  
Bending Moment ◽  
Axial Direction ◽  
Longitudinal Force ◽  
Combined Loading ◽  
Dimensional Problem ◽  
Elastic Plastic ◽  
Pipeline Section ◽  
Thin Walled Pipe

Рассмотрена задача упругопластического деформирования тонкостенной трубы при комбинированном нагружении изгибающим моментом, осевой силой и внутренним давлением. Решение задачи осуществлено по разработанной методике с помощью математического пакета Matcad численным методом, основанным на деформационной теории пластичности и безмоментной теории оболочек. Для упрощения решения предложено сведение двумерной задачи к одномерной задаче о деформировании балки, материал которой имеет различные диаграммы деформирования при сжатии и растяжении в осевом направлении. Проведено сравнение с результатами численного решения двумерной задачи методом конечных элементов в упругопластической постановке. Результаты расчета по инженерной методике совпадают с точным решением с точностью, необходимой для практического применения. Полученные результаты упругопластического решения для изгибающего момента в сечении трубопровода при комбинированном нагружении позволяют уточнить известное критериальное соотношение прочности сечения трубопровода с кольцевым дефектом в сторону снижения перебраковки. Применение разработанной методики позволяет ранжировать участки трубопровода с непроектным изгибом по степени близости к предельному состоянию при комбинированном нагружении изгибающим моментом, продольным усилием и внутренним давлением. The problem of elastic plastic deformation of a thin-walled pipe under co-binned loading by bending moment, axial force and internal pressure is considered. The problem is solved by the developed method using the Matcad mathematical package by a numerical method based on the deformation theory of plasticity and the momentless theory of shells. To simplify the solution of the problem, it is proposed to reduce a twodimensional problem to a one-dimensional problem about beam deformation, the material of which has different deformation diagrams under compression and tension in the axial direction. Comparison with the results of numerical solution of the two-dimensional problem with the finite element method in the elastic plastic formulation is carried out. The obtained results of the elastic-plastic solution for the bending moment in the pipeline section under combined loading make it possible to clarify criterion ratio of the strength of the pipeline section with an annular defect in the direction of reducing the rejection. Application of the developed approach allows to rank pipeline sections with non-design bending in the steppe close to the limit state under combined loading of the pipeline with bending moment, longitudinal force and internal pressure.

3-D Finite Element Simulation of Pulsating T-Shape Hydroforming of Tubes

2007 ◽  
Vol 340-341 ◽  
pp. 353-358 ◽  
Author(s):  
M. Loh-Mousavi ◽  
Kenichiro Mori ◽  
K. Hayashi ◽  
Seijiro Maki ◽  
M. Bakhshi
Keyword(s):  
Finite Element ◽  
Internal Pressure ◽  
Finite Element Simulation ◽  
Wall Thickness ◽  
Filling Ratio ◽  
Shape Accuracy ◽  
Element Simulation ◽  
Hydroforming Process ◽  
Good Agreement

The effect of oscillation of internal pressure on the formability and shape accuracy of the products in a pulsating hydroforming process of T-shaped parts was examined by finite element simulation. The local thinning was prevented by oscillating the internal pressure. The filling ratio of the die cavity and the symmetrical degree of the filling was increased by the oscillation of pressure. The calculated deforming shape and the wall thickness are in good agreement with the experimental ones. It was found that pulsating hydroforming is useful in improving the formability and shape accuracy in the T-shape hydroforming operation.

Effect of Expansion Ratio and Wall Thickness on Large-Diameter Solid Expandable Tubular after Expansion

2021 ◽  
Author(s):  
Changshuai Shi ◽  
Kailin Chen ◽  
Xiaohua Zhu ◽  
Feilong Cheng ◽  
Yuekui Qi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Internal Pressure ◽  
Wall Thickness ◽  
Performance Test ◽  
Large Diameter ◽  
Expansion Ratio ◽  
Fe Model ◽  
Laboratory Test Results ◽  
Low Efficiency ◽  
Pressure Resistance

Abstract The large-diameter solid expandable tubular with a smaller wall thickness faces the risk of internal pressure burst and external squeeze collapse in repairing damaged casing well. The internal pressure and external squeezing resistance calculation of the tubes using the analytical method require many expansion experiments and post-expansion tensile experiments, resulting in high costs and low efficiency. This paper gives a set of laboratory expansion and post-expansion performance test, which is based on the laboratory experiment and mechanical properties of material expansion. Two materials are studied: 316L and 20G. Then it analyses the error and causes of the error in the traditional analytical algorithm. Besides, it establishes an accurate finite element (FE) model to study the quantitative influence of expansion ratio and wall thickness on the burst strengths and collapse strengths of the tube. The results show that the toughness and hardening ratio of 316L is better than 20G at the same expansion ratio. The numerical simulation results of the model can effectively simulate the expansion process and the mechanical properties of SET in good agreement with the laboratory test results. The expansion ratio and wall thickness affect the mechanical properties after expansion. Thus the quantitative laws of the expansion driving force, internal pressure resistance, and external squeezing resistance under different variables are summarized. To ensure the integrity of the reinforced wellbore, the expansion ratio should not exceed 12.7%. In the current study lays a theoretical basis and technical support for optimizing SET and preventing downhole accidents.

Tube-Bulging Under Internal Pressure and Axial Force

1973 ◽  
Vol 95 (4) ◽  
pp. 219-223 ◽  
Author(s):  
D. M. Woo
Keyword(s):  
Internal Pressure ◽  
Numerical Solution ◽  
Axial Force ◽  
Compressive Load ◽  
Experimental Results ◽  
Longitudinal Stress ◽  
Thin Walled Tube ◽  
Thin Walled ◽  
Tube Bulging

A numerical solution for analysis of the bulging process of a thin-walled tube under internal pressure and axial force is proposed. The solution is applied to a case in which the longitudinal stress resulted from internal pressure and external compressive load is tensile along the whole length of the bulged tube. To verify whether the solution is applicable, theoretical and experimental results on the bulging of copper tubes have been obtained and are compared in this paper.

Influence of the Wall Thickness on the Allowable and Failure Pressures of Two- and Tree-Way Globe Valve Bodies

2011 ◽  
Vol 488-489 ◽  
pp. 646-649
Author(s):  
Milan Opalić ◽  
Ivica Galić ◽  
Krešimir Vučković
Keyword(s):  
Internal Pressure ◽  
Wall Thickness ◽  
Design Method ◽  
Equivalent Plastic Strain ◽  
Strain Curve ◽  
Linear Motion ◽  
Valve Body ◽  
Failure Pressure ◽  
Critical Location ◽  
Globe Valve

A globe valve is a linear motion valve used to shut off and regulate fluid flow in pipelines. Depending on the number of process connections, they are produced as two‑ or three-way valves. The main valve component carrying the internal pressure is the valve body. For safe exploitation, the valves are designed with the allowable internal pressure taken into consideration. The aim of this paper is to investigate the influence of the wall thickness on the allowable and failure pressures of two- and tree-way globe valve bodies, DN50 and DN100 respectively. Twice-elastic-slope (TES) and the tangent‑intersection (TI) methods are used to obtain the plastic collapse pressures at the critical location which was determined (Fig. 1a and 1b) at the location where maximum equivalent plastic strain throughout the valve body thickness reaches the outer surface. Obtained values are used afterwards to calculate corresponding allowable pressures according to the limit design method, while the failure pressure at the same location was determined as the highest point from the load-maximal principal strain curve. Calculated allowable pressure values, for both valve bodies, are compared with the corresponding ones obtained using the EN standard.

Sign in / Sign up

Export Citation Format

Share Document