The Compact Industrial Gas Turbine Recent Technical Improvements

1978 ◽  
Author(s):  
A. W. T. Mottram
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Aircraft Engine ◽  
Industrial Applications ◽  
Aircraft Engines ◽  
Technical Standard ◽  
Continual Improvement ◽  
Industrial Gas Turbines ◽  
Environmental Requirements ◽  
Industrial Gas Turbine

The industrial gas turbine requires continual improvement in order to increase output and efficiency, to extend its life and to meet fresh environmental requirements. In the compact industrial gas turbine, derived from the aircraft engine, the required improvements are achieved in three ways: (a) new features are incorporated which have been developed to meet the specific requirements of industrial applications, (b) technical improvements developed initially for aircraft engines are applied to existing industrial engines, and (c) new engines developed for aircraft and to a higher technical standard are introduced into industrial service. This paper describes recent improvements to Rolls-Royce compact industrial gas turbines with particular reference to the Olympus C and Olympus 593.

Transonic Compressor Development for Large Industrial Gas Turbines

1983 ◽  
Vol 105 (3) ◽  
pp. 417-421 ◽  
Author(s):  
B. Becker ◽  
M. Kwasniewski ◽  
O. von Schwerdtner
Keyword(s):  
Gas Turbine ◽  
Mass Flow ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Industrial Applications ◽  
Transonic Compressor ◽  
Industrial Gas Turbines ◽  
Compressor Map ◽  
Industrial Gas Turbine ◽  
Cycle Efficiency

With increasing mass flow and constant rotational speed of the single shaft gas turbine, the diameters and tip speeds of compressor and turbine blading have to be enlarged. A significant further increase in mass flow can be achieved with transonic compressor stages, as they have been in service in aero gas turbines for many years. For industrial applications, weight and stage pressure ratio are not nearly as important as efficiency. Therefore, different design criteria had to be applied, which led to a moderate front stage pressure ratio of 1.5 with a rotor tip inlet Mach number of 1.37 and a high solidity blading. In order to simulate the first three stages of a 200-MW gas turbine, a test compressor scaled by 1:5.4 was built and tested. These measurements confirmed the aerodynamic performance in the design point very well. The compressor map showed a satisfactory part speed behavior. These results prove that the single-shaft industrial gas turbine still has a high development potential with respect to power increase. Additionally, with the higher pressure ratio, the cycle efficiency will be improved considerably.

Evaluation Program for New Industrial Gas Turbine Materials

1978 ◽  
Vol 100 (4) ◽  
pp. 704-710
Author(s):  
Ch. Just ◽  
C. J. Franklin
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Time Cost ◽  
New Materials ◽  
Evaluation Program ◽  
Evaluation Time ◽  
Industrial Gas Turbines ◽  
New Material ◽  
Industrial Gas Turbine ◽  
Phase Evaluation

The need for a thorough and systematic standard evaluation program for new materials for modern industrial gas turbines is shown by several examples and facts. A complete list of the data required by the designer of an industrial gas turbine is given, together with comments to some of the more important properties. A six-phase evaluation program is described which minimizes evaluation time, cost, and the risk of introducing a new material.

scholarly journals The Effects of Chemistry Variations in New Nickel-Based Superalloys for Industrial Gas Turbine Applications

2020 ◽  
Vol 51 (9) ◽  
pp. 4902-4921 ◽  
Author(s):  
Sabin Sulzer ◽  
Magnus Hasselqvist ◽  
Hideyuki Murakami ◽  
Paul Bagot ◽  
Michael Moody ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Experimental Characterization ◽  
Multi Scale ◽  
Aerospace Applications ◽  
Scale Modeling ◽  
Industrial Gas Turbines ◽  
Multi Scale Modeling ◽  
Superior Corrosion Resistance ◽  
Industrial Gas Turbine

Abstract Industrial gas turbines (IGT) require novel single-crystal superalloys with demonstrably superior corrosion resistance to those used for aerospace applications and thus higher Cr contents. Multi-scale modeling approaches are aiding in the design of new alloy grades; however, the CALPHAD databases on which these rely remain unproven in this composition regime. A set of trial nickel-based superalloys for IGT blades is investigated, with carefully designed chemistries which isolate the influence of individual additions. Results from an extensive experimental characterization campaign are compared with CALPHAD predictions. Insights gained from this study are used to derive guidelines for optimized gas turbine alloy design and to gauge the reliability of the CALPHAD databases.

Performance Deterioration in Industrial Gas Turbines

1992 ◽  
Vol 114 (2) ◽  
pp. 161-168 ◽  
Author(s):  
I. S. Diakunchak
Keyword(s):  
Gas Turbine ◽  
Service Time ◽  
Gas Turbines ◽  
Engine Performance ◽  
Turbine Engine ◽  
Factors Affecting ◽  
Preventative Measures ◽  
Industrial Gas Turbines ◽  
Performance Deterioration ◽  
Industrial Gas Turbine

This paper describes the most important factors affecting the industrial gas turbine engine performance deterioration with service time and provides some approximate data on the prediction of the rate of deterioration. Recommendations are made on how to detect and monitor the performance deterioration. Preventative measures, which can be taken to avoid or retard the performance deterioration, are described in some detail.

The Two-Shaft Industrial Gas Turbine Goes to Sea — Again

1971 ◽  
Author(s):  
Arne Loft
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
State Control ◽  
Flexible Control ◽  
Second Stage ◽  
Sequential Systems ◽  
Industrial Gas Turbines ◽  
Heavy Duty Gas Turbine ◽  
Basic Characteristics ◽  
Industrial Gas Turbine

This paper gives a brief summary of the experience of the first industrial gas turbine ship, the John Sergeant, then enumerates the basic characteristics of the heavy duty gas turbine and the philosophy employed in the design. The unique features of the second-stage variable area turbine nozzle, its effects on performance, and particularly the flexible control it affords in conjunction with the controllable and reversible pitch propeller, are discussed. The philosophy of design of the solid state control, protection and sequential systems are outlined, as are the experiences to date with a number of industrial gas turbines of the two-shaft, off-shore and heavy fuel varieties. It concludes by discussing some of the considerations for burning residual fuel and boil-off from liquefied natural gas.

Turbine Tip Clearance Measurement System Evaluation on an Industrial Gas Turbine

1997 ◽  
Author(s):  
S. J. Gill ◽  
M. D. Ingallinera ◽  
A. G. Sheard
Keyword(s):  
Gas Turbine ◽  
Measurement System ◽  
Gas Turbines ◽  
Turbine Blades ◽  
Tip Clearance ◽  
Real Time Measurement ◽  
Gap Measurement ◽  
Industrial Gas Turbines ◽  
Blade Tip ◽  
Industrial Gas Turbine

The continuing development of industrial gas turbines is resulting in machines of increasing power and efficiency. The need to continue this trend is focusing attention on minimizing all loss mechanisms within the machine, including those associated with turbine blade tip clearance. In order to study tip clearance in the turbine, real time measurement is required of clearance between turbine blades and the casing in which they run. This measurement is not routinely performed, due to the harsh nature of the turbine environment. On those occasions when turbine tip clearance is measured, it is typically in development vehicles, often using cooled probes that are somewhat unsuitable for use in production gas turbines. In this paper a program of work is reported that was undertaken with the purpose of identifying a promising turbine tip clearance measurement system that used the capacitive gap measurement technique. Issues surrounding the application of three systems to the turbine section of a GE MS6001FA gas turbine are identified and reported. Performance of the three evaluated systems is analyzed.

Performance Deterioration in Industrial Gas Turbines

1991 ◽  
Author(s):  
Ihor S. Diakunchak
Keyword(s):  
Gas Turbine ◽  
Service Time ◽  
Gas Turbines ◽  
Engine Performance ◽  
Turbine Engine ◽  
Factors Affecting ◽  
Preventative Measures ◽  
Industrial Gas Turbines ◽  
Performance Deterioration ◽  
Industrial Gas Turbine

This paper describes the most important factors affecting the industrial gas turbine engine performance deterioration with service time and provides some approximate data on the prediction of the rate of deterioration. Recommendations are made on how to detect and monitor the performance deterioration. Preventative measures, which can be taken to avoid or retard the performance deterioration, are described in some detail.

Study of Using Exhaust Gas Recirculation on a Gas Turbine for Carbon Capture

2020 ◽  
Author(s):  
Dan Burnes ◽  
Priyank Saxena ◽  
Paul Dunn
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Carbon Capture ◽  
Hydrocarbon Fuel ◽  
Exhaust Gas Recirculation ◽  
Exhaust Gas ◽  
Hybrid Solutions ◽  
Industrial Gas Turbines ◽  
Industrial Gas Turbine ◽  
Gas Recirculation

Abstract The growing call of minimizing carbon dioxide and other greenhouse gases emitting from energy and transportation products will spur innovation to meet new stringent requirements while striving to preserve significant investments in the current infrastructure. This paper presents quantitative analysis of exhaust gas recirculation (EGR) on industrial gas turbines to enable carbon sequestration venturing towards emission free operation. This study will show the effect of using EGR on gas turbine performance and operation, combustion characteristics, and demonstrate potential hybrid solutions with detailed constituent accounting. Both single shaft and two shaft gas turbines for power generation and mechanically driven equipment are considered for application of this technology. One key element is assessing the combustion system operating at reduced O2 levels within the industrial gas turbine. With the gas turbine behavior operating with EGR defined at a reasonable operating state, a parametric study shows rates of CO2 sequestration along with quantifying supplemental O2 required at the inlet, if needed, to sustain combustion. With rates of capture known, a further exploration is examined reviewing potential utilities, monetizing these sequestered constituents. Ultimately, the objective is to preview a potential future of operating industrial gas turbines in a non-emissive and in some cases carbon negative manner while still using hydrocarbon fuel.

Evaluation of Combustion and Emissions Using Biodiesel and Blends With Kerosene in a Low NOx Gas Turbine Combustor

2010 ◽  
Author(s):  
Hu Li ◽  
Mohamed Altaher ◽  
Gordon E. Andrews
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Equivalence Ratio ◽  
Fuel Injection ◽  
Waste Cooking Oil ◽  
Industrial Applications ◽  
Liquid Fuels ◽  
Gaseous Emissions ◽  
Gas Turbine Combustor ◽  
Industrial Gas Turbines

Biofuels offer reduced CO2 emissions for both industrial and aero gas turbines. Industrial applications are more practical due to low temperature waxing problems at altitude. Any use of biofuels in industrial gas turbines must also achieve low NOx and this paper investigates the use of biofuels in a low NOx radial swirler, as used in some industrial low NOx gas turbines. A waste cooking oil derived methyl ester biodiesel (WME) has been tested on a radial swirler industrial low NOx gas turbine combustor under atmospheric pressure and 600K. The pure WME and its blends with kerosene, B20 and B50 (WME:kerosene = 20:80 and 50:50 respectively), and pure kerosene were tested for gaseous emissions and lean extinction as a function of equivalence ratio. The co-firing with natural gas (NG) was tested for kerosene/biofuel blends B20 and B50. The central fuel injection was used for liquid fuels and wall injection was used for NG. The experiments were carried out at a reference Mach number of 0.017. The inlet air to the combustor was heated to 600K. The results show that B20 produced similar NOx at an equivalence ratio of ∼0.5 and a significant low NOx when the equivalence ratio was increased comparing with kerosene. B50 and B100 produced higher NOx compared to kerosene, which indicates deteriorated mixing due to the poor volatility of the biofuel component. The biodiesel lower hydrocarbon and CO emissions than kerosene in the lean combustion range. The lean extinction limit was lower for B50 and B100 than kerosene. It is demonstrated that B20 has the lowest overall emissions. The co-firing with NG using B20 and B50 significantly reduced NOx and CO emissions.

Development and F-Class Industrial Gas Turbine Engine Testing of Smart Components With Direct-Write Embedded Sensors and High Temperature Wireless Telemetry

2008 ◽  
Author(s):  
David Mitchell ◽  
Anand Kulkarni ◽  
Edward Roesch ◽  
Ramesh Subramanian ◽  
Andrew Burns ◽  
...  
Keyword(s):  
High Temperature ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Condition Based Maintenance ◽  
Direct Write ◽  
Turbine Engine ◽  
Wireless Telemetry ◽  
Industrial Gas Turbines ◽  
Engine Testing ◽  
Industrial Gas Turbine

The potential for savings provided to worldwide operators of industrial gas turbines, by transitioning from the current standard of interval-based maintenance to condition-based maintenance may be in the tens of millions of dollars per year. Knowledge of the historical and current condition of life-limiting components will enable more efficient use of industrial gas turbine resources via increased operational flexibility, with less risk of unplanned outages as a result of off-parameter operations. To date, it has been impossible to apply true condition-based maintenance to industrial gas turbines because the extremely harsh operating conditions in the heart of a gas turbine preclude using the necessary advanced sensor systems to monitor the machine’s condition continuously. The U.S. Department of Commerce’s National Institute of Standards and Technology – Advanced Technology Program (NIST-ATP) awarded the Joint Venture team of Siemens Power Generation, Inc. and MesoScribe Technologies, Inc. a four-year, $5.4 million program in November, 2004, titled Conformal, Direct-Write-Technology-Enabled, Wireless, Smart Turbine Components. The target was to develop a potentially industry-changing technology to build smart, self-aware engine components that incorporate embedded, harsh-environment-capable sensors and high temperature capable wireless telemetry systems for continuously monitoring component condition in both the compressor and turbine sections. The approach involves several difficult engineering challenges, including the need to embed sensors on complex shapes, such as turbine blades, embedding wireless telemetry systems in regions with temperatures that preclude the use of conventional silicon-based electronics, protecting both sensors and wireless devices from the extreme temperatures and environments of an operating gas turbine, and successfully transmitting the sensor information from an environment very hostile to wireless signals. The program included full-scale, F-class industrial gas turbine engine test demonstrations with smart components in both the compressor and turbine sections. The results of the development program and engine testing to date will be discussed.

Sign in / Sign up

Export Citation Format

Share Document