Large, Flexible, Efficient, 750°C Closed Gas Cycle Coal-Fired or Nuclear Cogeneration Plants

1980 ◽  
Author(s):  
Z. P. Tilliette ◽  
B. Pierre
Keyword(s):  
Gas Turbine ◽  
Nuclear Power ◽  
Power Plants ◽  
Hot Water ◽  
Inlet Temperature ◽  
Oil Consumption ◽  
Turbine Inlet Temperature ◽  
Pressure Steam ◽  
Conversion Coefficients ◽  
Steam Superheating

A now unavoidable concern is the best possible use of a given energy source in order to meet the demand of power and heat. The most efficient, rational, thermodynamically satisfactory way of producing heat is to cogenerate it with power and to handle it as a by-product. Another basic condition is to supply heat without disturbing the operation of main turbogenerators. Closed helium cycle, non-intercooled, gas turbine coal-fired and nuclear power plants which meet these requirements are presented in this paper. Low-pressure steam and hot water are recovered from the precooler; medium, high pressure steam and steam superheating are generated by means of a bypass arrangement of the recuperator. The concept offers attractive overall energy conversion coefficients, very flexible heat production conditions and significant potentialities of reducing oil consumption. Results are given for the conservative 750 C gas turbine inlet temperature.

An Efficient, Flexible Arrangement to Generate High Quality Process or Domestic Heat in Recuperative Gas Cycle Power Plants: Application to Helium Direct Cycle Nuclear Power Plants

1979 ◽  
Vol 101 (1) ◽  
pp. 130-140 ◽  
Author(s):  
Z. P. Tilliette ◽  
B. Pierre ◽  
P. F. Jude
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Hot Water ◽  
Primary Circuit ◽  
Inlet Temperature ◽  
Total Efficiency ◽  
High Quality ◽  
Quality Process ◽  
Direct Cycle

The advantages of gas turbine power plants in general and closed cycle systems under gas pressure in particular for waste heat recovery are well known. A satisfactory efficiency for electric power generation and good conditions to obtain a significant amount of hot water above 100°C lead to a high fuel utilization. However, as in most of projects, it is not much possible to produce high temperature steam or water without significantly decreasing the electricity production. A new method for an additional generation of high quality process or domestic heat is proposed. The basic feature of this method lies in arranging one or two steam generators or preheaters in parallel with the low pressure side of the recuperator. The high total efficiency and the noteworthy flexibility of this system are emphasized. This arrangement is suitable for any kind of heat source, but the applications presented in this paper are related to helium direct cycle nuclear power plants the main features of which are a single 600 MW(e) turbomachine, a turbine inlet temperature of 775°C, no or one intermediate cooling and a primary circuit fully integrated in a pre-stressed concrete reactor vessel.

Efficient Power Generation From Large 750°C Heat Sources: Application to Coal-Fired and Nuclear Power Stations

1980 ◽  
Author(s):  
Z. P. Tilliette ◽  
B. Pierre
Keyword(s):  
Power Generation ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Energy ◽  
Inlet Temperature ◽  
Heat Sources ◽  
Turbine Inlet Temperature ◽  
Power Stations ◽  
Efficient Power ◽  
Steam Cycle

Considering the concern about a more efficient, rational use of heat sources, and a greater location flexibility of power plants owing to cooling capability, closed gas cycles can offer new solutions for fossil or nuclear energy. An efficient heat conversion into power is obtained by the combination of a main non-intercooled helium cycle with a flexible, superheated, low-pressure bottoming steam cycle. Emphasis is placed on the matching of the two cycles and, for that, a recuperator bypass arrangement is used. The operation of the main gas turbocompressor does not depend upon the operation of the small steam cycle. Results are presented for a conservative turbine inlet temperature of 750 C. Applications are made for a coal-fired power plant and for a nuclear GT-HTGR. Overall net plant efficiencies of 39 and 46 percent, respectively, are projected.

Development of a Maintenance Program for Major Gas Turbine Hot Gas Path Parts

2000 ◽  
Author(s):  
Hideto Moritsuka ◽  
Tomoharu Fujii ◽  
Takeshi Takahashi
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
Thermal Power ◽  
Management Program ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Maintenance Schedule ◽  
Hot Gas ◽  
Turbine Inlet

The thermal efficiency of gas turbine combined cycle power generation plants increase significantly in accordance with turbine inlet temperature. Gas turbine combined cycle power plants operating at high turbine inlet temperature are popular as a main thermal power station among our electric power companies in Japan. Thus, gas turbine hot gas parts are working under extreme conditions which will strongly affect their lifetime as well as maintenance costs for repaired and replaced parts. To reduce the latter is of major importance to enhance cost effectiveness of the plant. This report describes a gas turbine maintenance management program of main hot gas parts (combustor chambers, transition peices, turbine 1st. stage nozzles and 1st. stage buckets) for management persons of gas turbine combined cycle power stations in order to obtain an optimal gas turbine maintenance schedule considering rotation, repair and replacement or exchange of those parts.

Analysis of Integrated Cooling Systems for Gas Turbine Power Plants

2017 ◽  
Author(s):  
Waleed El-Damaty ◽  
Mohamed Gadalla
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
Turbine Blades ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Air Cooling ◽  
Turbine Inlet Temperature ◽  
Current Increase ◽  
Turbine Inlet ◽  
Compact Size

With the current increase in electricity consumption and energy demand, most of the research focus is shifted towards the means of increasing the power plants efficiency in order to produce more electricity by using as less fuel as possible. Gas turbine power plants specifically have been under the study in the recent years due to its feasibility, low capital cost, simple design, compact size and higher efficiency compared to steam turbine power plants. There are a lot of operating conditions that affect the performance of the gas turbine which includes the inlet air climatic conditions, mass flow rate and the turbine inlet temperature. Many improvements and enhancements became applicable through the advancement in the material and cooling technologies. Cooling techniques could be used to cool the inlet air entering the compressor by utilizing evaporative coolers and mechanical chillers, and to cool the turbine blades in order to avoid a decline in the life of turbine blades due to unwanted exposure to thermal stresses and oxidation. Internal convection cooling, film cooling and transpiration cooling are the three main techniques that can be used in the process of turbine blades cooling. The main objective of this proposal is to improve the durability and performance of gas turbine power plants by proposing the usage of integrated system of solid desiccant with Maisotsenko cooler in the turbine blade cooling and inlet air cooling processes. Four configurations were presented and the results were an increase in the efficiency of the gas turbine cycle for all the cases specially the two stage Maisotsenko desiccant cooling system where the efficiency increased from 33.33% to 34.17% as well as maintaining the turbine inlet temperature at a desired level of 1500°K.

scholarly journals Gas Turbine and Combined Cycle Technologies for Power and Efficiency Enhancement in Power Plants

1994 ◽  
Author(s):  
Meherwan P. Boyce ◽  
Cyrus B. Meher-Homji ◽  
A. N. Lakshminarasimha
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Specific Work ◽  
Efficiency Enhancement ◽  
Turbine Inlet Temperature ◽  
Cycle Efficiency ◽  
Original Equipment Manufacturers

A wide variety of gas turbine based cycles exist in the market today with several technologies being promoted by individual Original Equipment Manufacturers. This paper is focused on providing users with a conceptual framework within which to view these cycles and choose suitable options for their needs. A basic parametric analysis is provided to show the interdependency of Turbine Inlet Temperature (TIT) and Pressure Ratio on cycle efficiency and specific work.

Development of a Maintenance Program for Major Gas Turbine Hot Gas Path Parts

2002 ◽  
Vol 124 (4) ◽  
pp. 867-873 ◽  
Author(s):  
H. Moritsuka ◽  
T. Fujii ◽  
T. Takahashi
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
Thermal Power ◽  
Management Program ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Maintenance Schedule ◽  
Hot Gas ◽  
Turbine Inlet

The thermal efficiency of gas turbine combined cycle power generation plants increase significantly in accordance with turbine inlet temperature. Gas turbine combined cycle power plants operating at high turbine inlet temperature are popular as a main thermal power station among our electric power companies in Japan. Thus, gas turbine hot gas parts are working under extreme conditions which will strongly affect their lifetime as well as maintenance costs for repaired and replaced parts. To reduce the latter is of major importance to enhance cost effectiveness of the plant. This report describes a gas turbine maintenance management program of main hot gas parts (combustor chambers, transition pieces, turbine first stage nozzles and first stage buckets) for management persons of gas turbine combined cycle power stations in order to obtain an optimal gas turbine maintenance schedule considering rotation, repair and replacement, or exchange of those parts.

Development and Fabrication of Silicon Nitride Components for Ceramic Gas Turbine

1997 ◽  
Author(s):  
Keisuke Makino ◽  
Ken-Ichi Mizuno ◽  
Toru Shimamori
Keyword(s):  
High Temperature ◽  
Silicon Nitride ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Blades ◽  
High Strength ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Spark Plug ◽  
Power Turbine

NGK Spark Plug Co., Ltd. has been developing various silicon nitride materials, and the technology for fabricating components for ceramic gas turbines (CGT) using theses materials. We are supplying silicon nitride material components for the project to develop 300 kW class CGT for co-generation in Japan. EC-152 was developed for components that require high strength at high temperature, such as turbine blades and turbine nozzles. In order to adapt the increasing of the turbine inlet temperature (TIT) up to 1,350 °C in accordance with the project goals, we developed two silicon nitride materials with further unproved properties: ST-1 and ST-2. ST-1 has a higher strength than EC-152 and is suitable for first stage turbine blades and power turbine blades. ST-2 has higher oxidation resistance than EC-152 and is suitable for power turbine nozzles. In this paper, we report on the properties of these materials, and present the results of evaluations of these materials when they are actually used for CGT components such as first stage turbine blades and power turbine nozzles.

Optimal Gas-Turbine Design for Hybrid Solar Power Plant Operation

2012 ◽  
Author(s):  
James Spelling ◽  
Björn Laumert ◽  
Torsten Fransson
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Power Plants ◽  
Solar Power ◽  
Pressure Ratio ◽  
Inlet Temperature ◽  
Electricity Cost ◽  
Conflicting Objectives ◽  
Dynamic Simulation Model ◽  
A Minor

A dynamic simulation model of a hybrid solar gas-turbine power plant has been developed, allowing determination of its thermodynamic and economic performance. In order to examine optimum gas-turbine designs for hybrid solar power plants, multi-objective thermoeconomic analysis has been performed, with two conflicting objectives: minimum levelized electricity costs and minimum specific CO2 emissions. Optimum cycle conditions: pressure-ratio, receiver temperature, turbine inlet temperature and flow rate, have been identified for a 15 MWe gas-turbine under different degrees of solarization. At moderate solar shares, the hybrid solar gas-turbine concept was shown to provide significant water and CO2 savings with only a minor increase in the levelized electricity cost.

Sign in / Sign up

Export Citation Format

Share Document