Theoretical and Experimental Study of the Dynamics of the Tripod-Ball Sliding Joint With Clearance

2001 ◽  
Author(s):  
Jia Xiaohong ◽  
Ji Linhong ◽  
Jin Dewen ◽  
Zhang Jichuan
Keyword(s):  
Mathematical Model ◽  
Equations Of Motion ◽  
Experimental Studies ◽  
Active System ◽  
New Concepts ◽  
Sliding Joint ◽  
New Type ◽  
Set Up ◽  
The Mathematical Model ◽  
Kane Method

Abstract Clearance is inevitable in the kinematic joints of mechanisms. In this paper the dynamic behavior of a crank-slider mechanism with clearance in its tripod-ball sliding joint is investigated theoretically and experimentally. The mathematical model of this new-type joint is established, and the new concepts of basal system and active system are put forward. Based on the mode-change criterion established in this paper, the consistent equations of motion in full-scale are derived by using Kane method. The experimental rig was set up to measure the effects of the clearance on the dynamic response. Corresponding experimental studies verify the theoretical results satisfactorily. In addition, due to the nonlinear elements in the improved mathematical model of the joint with clearance, the chaotic responses are found in numerical simulation.

Dynamics and Stability of Non-Planar Rigid Rotor Equipped with Two Ball-Spring Autobalancers

2019 ◽  
Vol 19 (02) ◽  
pp. 1950001 ◽  
Author(s):  
Mousa Rezaee ◽  
Mir Mohammad Ettefagh ◽  
Reza Fathi
Keyword(s):  
Mathematical Model ◽  
Nonlinear Equations ◽  
Equations Of Motion ◽  
Rigid Rotor ◽  
Out Of Plane ◽  
New Type ◽  
Nonlinear Equations Of Motion ◽  
The Mathematical Model ◽  
System Time

Recently, a new type of automatic ball balancer (ABB), called the ball-spring autobalancer (AB), has been proposed, which substantially eliminates the drawbacks of the traditional ABBs. In previous studies, the dynamics of the Jeffcott planar rotor equipped with ball-spring AB has been investigated. In the Jeffcott model, it is assumed that the ABB is located on the plane of the unbalance disk. However, for the non-planar rigid rotor with distributed imbalances, out-of-plane motions may occur, and the Jeffcott model becomes unreliable as the tilting motion cannot be explained. To this end, the aim of this paper is to analyze the capability of the ball-spring AB in balancing non-planar rotors and to reconfirm its pre-claimed advantages over the traditional ABBs for balancing non-planar rotors. To start, the mathematical model of the rigid rotor with two ball-spring ABs is established, based on which the nonlinear equations of motion are derived. Then, the system time responses are computed numerically and the balanced stable regions are acquired by the Lyapunov’s first method. The results of this study show that the ball-spring ABs can balance the non-planar rotors and the tilting motion does not impair the pre-claimed advantages of the ball-spring AB.

Fixture Optimization for Robotic Belt Grinding System

2011 ◽  
Vol 121-126 ◽  
pp. 2030-2034
Author(s):  
Dong Zhang ◽  
Chao Yun ◽  
Ling Zhang
Keyword(s):  
Mathematical Model ◽  
Optimization Methods ◽  
Belt Grinding ◽  
Robotic Grinding ◽  
The Monte Carlo Method ◽  
New Type ◽  
Set Up ◽  
Robotic Belt Grinding ◽  
The Mathematical Model ◽  
Grinding System

The precision is impacted when the robotic grinding path is discontinuous and the gripper needs to be replaced during manufacturing. In order to solve this problem, a new type PPPRRR grinding robot was proposed. The mathematical model for the robotic grinding paths was set up. The factors including the pose of the workpiece respect to the end joint and the position of contact wheel respect to the robot base frame {O}were analyzed to influence the grinding ability of the system. Base on the Monte Carlo method the posture and position factors above had been optimized, and the grinding ability of the system was increased. The optimization methods were proved right and workable by grinding golf head experiment.

EXPERIMENTAL STUDIES OF CAR PROPERTIES ON A PHYSICAL MODEL

2019 ◽  
pp. 10-16
Author(s):  
Oleksii Timkov ◽  
Dmytro Yashchenko ◽  
Volodymyr Bosenko
Keyword(s):  
Mathematical Model ◽  
Remote Control ◽  
Physical Model ◽  
Model Experiment ◽  
Experimental Studies ◽  
Electrical Energy ◽  
Short Term ◽  
Motor Current ◽  
Memory Card ◽  
The Mathematical Model

The article deals with the development of a physical model of a car equipped with measuring, recording and remote control equipment for experimental study of car properties. A detailed description of the design of the physical model and of the electronic modules used is given, links to application libraries and the code of the first part of the program for remote control of the model are given. Atmega microcontroller on the Arduino Uno platform was used to manage the model and register the parameters. When moving the car on the memory card saved such parameters as speed, voltage on the motor, current on the motor, the angle of the steered wheel, acceleration along three coordinate axes are recorded. Use of more powerful microcontrollers will allow to expand the list of the registered parameters of movement of the car. It is possible to measure the forces acting on the elements of the car and other parameters. In the future, it is planned to develop a mathematical model of motion of the car and check its adequacy in conducting experimental studies on maneuverability on the physical model. In addition, it is possible to conduct studies of stability and consumption of electrical energy. The physical model allows to quickly change geometric dimensions and mass parameters. In the study of highway trains, this approach will allow to investigate the various layout schemes of highway trains in the short term. It is possible to make two-axle road trains and saddle towed trains, three-way hitched trains of different layout. The results obtained will allow us to improve not only the mathematical model, but also the experimental physical model, and move on to further study the properties of hybrid road trains with an active trailer link. This approach allows to reduce material and time costs when researching the properties of cars and road trains. Keywords: car, physical model, experiment, road trains, sensor, remote control, maneuverability, stability.

Research on Dynamic Balance Method of Precision Centrifuge

2014 ◽  
Vol 945-949 ◽  
pp. 777-780
Author(s):  
Tao Liu ◽  
Yong Xu ◽  
Bo Yuan Mao
Keyword(s):  
Mathematical Model ◽  
Balance Control ◽  
Dynamic Balance ◽  
Dynamic Balancing ◽  
Structure Characteristics ◽  
Balance System ◽  
Simulation Results ◽  
Set Up ◽  
System Controller ◽  
The Mathematical Model

Firstly, according to the structure characteristics of precision centrifuge, the mathematical model of its dynamic balancing system was set up, and the dynamic balancing scheme of double test surfaces, double emendation surfaces were established. Then the dynamic balance system controller of precision centrifuge was designed. Simulation results show that the controller designed can completely meet the requirements of precision centrifuge dynamic balance control system.

Study on the working state of the five hundred-meter aperture spherical telescope using step-wise assignment method

2014 ◽  
Vol 229 (2) ◽  
pp. 316-324 ◽  
Author(s):  
Yu Liu ◽  
Feng Gao
Keyword(s):  
Nonlinear Equations ◽  
Analytical Solutions ◽  
Driving Mechanism ◽  
Initial Value ◽  
Unknown Parameters ◽  
Support Structure ◽  
Assignment Method ◽  
New Type ◽  
Set Up ◽  
The Mathematical Model

The working state of the five hundred-meter aperture spherical telescope (FAST) is solved using the step-wise assignment method. In this paper, the mathematical model of the cable-net support structure of the FAST is set up by the catenary equation. There are a large number of nonlinear equations and unknown parameters of the model. The nonlinear equations are solved by using the step-wise assignment method. The method is using the analytical solutions of the cable-net equations of one working state as the initial value for the next working state, from which the analytical solutions of the nonlinear equations of the cable-net for each working state of the FAST and the tension and length of each driving cable can be obtained. The suggested algorithm is quite practically well suited to study the working state of the cable-net structures of the FAST. Also, the working state analysis result of the cable-net support structure of a reduced model of the cable-net structure reflector for the FAST is given to verify the reliability of the method. In order to show the validity of the method, comparisons with another algorithm to set the initial value are presented. This method has an important guiding significance to the further study on the control of the new type of flexible cable driving mechanism, especially the FAST.

scholarly journals Use of the mathematical model of the ignition system to analyze the spark discharge, including the destruction of spark plug electrodes

Open Physics ◽  
2018 ◽  
Vol 16 (1) ◽  
pp. 57-62 ◽  
Author(s):  
Sebastian Różowicz
Keyword(s):  
Mathematical Model ◽  
Experimental Studies ◽  
Fuel Mixture ◽  
Spark Discharge ◽  
Fuel Additives ◽  
Ignition System ◽  
Spark Plug ◽  
The Mathematical Model

Abstract The paper presents the results of analytical and experimental studies concerning the influence of different kinds of fuel additives on the quality of the spark discharge for different configurations of the ignition system. The wear of the spark plug electrode and the value of spark discharge were determined for various impurities and configurations of the air-fuel mixture.

Mobile Worm-Like Robots for Pipe Inspection

2015 ◽  
pp. 168-218 ◽  
Author(s):  
Sergey Fedorovich Jatsun ◽  
Andrei Vasilevich Malchikov
Keyword(s):  
Mathematical Model ◽  
Control System ◽  
Mobile Robots ◽  
Experimental Studies ◽  
Design Parameters ◽  
Robot Motion ◽  
Robot Dynamics ◽  
Confined Space ◽  
Pipe Inspection ◽  
The Mathematical Model

This chapter describes various designs of multilink mobile robots intended to move inside the confined space of pipelines. The mathematical model that describes robot dynamics and controlled motion, which allows simulating different regimes of robot motion and determining design parameters of the device and its control system, is presented. The chapter contains the results of numerical simulations for different types of worm-like mobile robots. The experimental studies of the in-pipe robots prototypes and their analyses are presented in this chapter.

Valve Gear Refinement

2000 ◽  
Vol 124 (1) ◽  
pp. 86-90 ◽  
Author(s):  
Jurij Avsec ◽  
Milan Marcic ◽  
Maks Oblak
Keyword(s):  
Mathematical Model ◽  
Cam Design ◽  
Cam Follower ◽  
New Type ◽  
Cam Profile ◽  
Profile Design ◽  
Comparison Of The Results ◽  
The Mathematical Model ◽  
Valve Gear ◽  
Lubrication Properties

This paper describes a new type of valve gear cam—MULTICAM—which consists of seven curves and allows an optimum cam profile design. In order to calculate the cinematic and dynamic values and to assess the minimum oil film thickness in the valve gear, the mathematical model of an ideal valve gear was used. In addition, the comparison of the results between the polysine cam and the new MULTICAM cam design was made. By means of the new cam design the Hertz pressures were reduced at the point of contact between the cam and the cam follower and the lubrication properties at the top of the cam improved.

Adsorption-Desorption Processes in Adsorption Chillers

2016 ◽  
Vol 20 (2) ◽  
pp. 81-89
Author(s):  
Monika Gwadera
Keyword(s):  
Mathematical Modeling ◽  
Mathematical Model ◽  
Mass Transfer ◽  
Experimental Studies ◽  
Operating Principle ◽  
Adsorption Desorption ◽  
The Mathematical Model

AbstractThe aim of this paper is to present the adsorption chillers technology. The operating principle of these systems, the adsorbent-adsorbate pairs that are frequently applied and the enhancement techniques that allow improvement of their efficiency are presented. Analysis of the mass transfer and principles of mathematical modeling of such systems are also discussed. In the further part of the text, the results of experimental studies and comparison of these results with calculations based on the mathematical model of adsorption were presented.

Self-Generated Torque Induced by the Lockable and Self-Locking Differentials within the 4WD Drivetrain

2014 ◽  
Vol 659 ◽  
pp. 268-273
Author(s):  
Marian Truta ◽  
Marin Marinescu ◽  
Radu Vilau ◽  
Octavian Alexa ◽  
Constantin Ovidiu Ilie
Keyword(s):  
Mathematical Model ◽  
Internal Friction ◽  
The Self ◽  
Multiple Tests ◽  
Coefficient Variation ◽  
Comprehensive Theory ◽  
New Concepts ◽  
Road Surfaces ◽  
The Mathematical Model

This work is dealing with the self-generated torque that occurs within a 4WD military special automotive drivetrain. The mathematical model stated in this paper is confirmed by the means of multiple tests developed in real conditions. The tests were developed in order to reveal both transversal and longitudinal self-generated torque within the drivetrain, on different road surfaces. The present paper also introduces some new concepts, such is for instance the insensitive domain of a self-locking (or a progressively locking) differential. With the aid of this concept we can easier deal with the self-generated torque that is due to the increased internal friction of the differential. Moreover, a general, comprehensive theory can be further issued that could classify the self-locking differentials according to their internal friction and their locking coefficient variation.

Sign in / Sign up

Export Citation Format

Share Document