Dynamic Stability of Parallel Manipulator at its Singularities Corresponding to Kinematic Parameters of Dynamic Systems

2018 ◽  
Author(s):  
Li Yu-Tong ◽  
Wang Yu-Xin
Keyword(s):  
Dynamic Stability ◽  
Particle System ◽  
Parallel Mechanisms ◽  
Kinematic Parameters ◽  
Positive Real ◽  
Planning Stage ◽  
Motion Stability ◽  
Singular Configurations ◽  
Movable Platform ◽  
Singular Configuration

With the aid of the Liyapunov first approximate stability criterion, the dynamic stability condition for the 3-RPR parallel mechanism to realize a deterministic motion at singular configurations is deduced. Based on this condition, the distributions of the kinematic parameters including input velocities and accelerations of the system corresponding to the stable motion at its singular configuration are investigated then. It is found that for a given singular configuration, increasing input velocities and accelerations, the sub-distributions of eigenvalues with positive real parts have a tendency to shrink and, consequently, the motion stability at the singular configuration can be enhanced; adjusting input velocities and accelerations only can not necessarily get all negative real parts of the eigenvalues sharing a common intersection of the distributing subintervals and, normally, the additional adjustment of initial velocities of the particle system should be added. Besides, while the movable platform goes through the singular configuration, if the control law of the input parameters makes the instantaneous velocity center of the movable platform far away from the singular point, the platform is able to go through the singular configuration with high stability and strong capability to resist external disturbances. This research indicates the effectiveness to improve the motion stability of the dynamics system at singular configurations via adjusting the input kinematic parameters. From this, a singularity-free approach via adjusting the input kinematic parameters can be utilized to exclude singularities of parallel mechanisms dynamically in the joint trajectory planning stage without introducing either redundancy or active mass.

Improving Motion Stability of the Plane 3-RPR Parallel Manipulator at Singular Configuration

2018 ◽  
Author(s):  
Yu-Tong Li ◽  
Yu-Xin Wang
Keyword(s):  
Parallel Manipulator ◽  
Parallel Manipulators ◽  
Angular Speed ◽  
Motion Stability ◽  
Singular Configurations ◽  
Movable Platform ◽  
Singular Configuration ◽  
Translation Type ◽  
External Forces ◽  
Gerschgorin Circle

Kinematic parameters have significant influences on the motion stability of parallel manipulators at singular configureations. Taking the plane 3-RPR parallel manipulator as an example, the motion stability at different types of singular configurations corresponding to the angular speed and velocity of the movable platform are investigated. At first, the second order of uncoupled dynamics equation for the 3-RPR parallel manipulator is established with the aid of the second class Lagrange approach. According to the Lyapunov first approximate stability criterion, the approximate conditions for the 3-RPR parallel manipulator with a stabile motion at singular configurations are determined based on the Gerschgorin circle theorem. Next, the exact Hurwitz criterion is utilized to study the motion stability and the load capability of the manipulator corresponding to the angular speed and velocity of the movable platform, as well as the directions of the external forces at two kinds of singular configurations: with a gained rotation-type DOF, and with a gained translation-type DOF, respectively. The results show that increasing both the angular speed and the velocity of the mass center of the movable platform can efficiently improve the motion stability of the 3-RPR parallel manipulator at singular configurations.

Singularity Analysis of 3-DOF Planar Parallel Mechanisms via Screw Theory

2003 ◽  
Vol 125 (3) ◽  
pp. 573-581 ◽  
Author(s):  
Ilian A. Bonev ◽  
Dimiter Zlatanov ◽  
Cle´ment M. Gosselin
Keyword(s):  
Screw Theory ◽  
Singularity Analysis ◽  
Point Of View ◽  
Mobile Platform ◽  
Parallel Mechanisms ◽  
Singular Configurations ◽  
Revolute Joints ◽  
Singular Configuration

This paper presents the results of a detailed study of the singular configurations of 3-DOF planar parallel mechanisms with three identical legs. Only prismatic and revolute joints are considered. From the point of view of singularity analysis, there are ten different architectures. All of them are examined in a compact and systematic manner using planar screw theory. The nature of each possible singular configuration is discussed and the singularity loci for a constant orientation of the mobile platform are obtained. For some architectures, simplified designs with easy to determine singularities are identified.

Error Compensation Based on Differential Operators and Electro-Optical Collimation

2010 ◽  
Vol 44-47 ◽  
pp. 1568-1572 ◽  
Author(s):  
Lin Hong ◽  
Yan Shu Liang ◽  
Meng Cong
Keyword(s):  
Error Compensation ◽  
Differential Operators ◽  
Three Dimension ◽  
Parallel Mechanisms ◽  
Linear Calibration ◽  
Error Sources ◽  
Collimation System ◽  
Simulation And Experiment ◽  
Movable Platform ◽  
Calibration Techniques

Theoretical analysis and experiment study on the pose error compensations of parallel mechanisms have been presented. A method for error compensations by means of differential operators and electro-optical collimation system is discussed. Compensation quantities oriented to main error sources from position coordinates of joints on the movable platform can be obtained through mathematic models. Compensation quantities provided by driving legs can be realized precisely by linear calibration techniques. Orientation angles can be measured by means of electro-optical collimation system and a three-dimension turning table, which is centrally positioned and can complete multi-direction inverse adjusting. Numerical example relevant to Stewart platform has been given. Simulation and experiment results indicate the feasibility of the method.

Singularity-locus expression of a class of parallel mechanisms

Robotica ◽  
2002 ◽  
Vol 20 (3) ◽  
pp. 323-328 ◽  
Author(s):  
Raffaele Di Gregorio
Keyword(s):  
Polynomial Equation ◽  
Geometric Parameters ◽  
General Mechanism ◽  
Parallel Mechanisms ◽  
Degree Polynomial ◽  
Singular Configurations ◽  
Singularity Locus ◽  
Orientation Parameters

In parallel mechanisms, singular configurations (singularities) have to be avoided during motion. All the singularities should be located in order to avoid them. Hence, relationships involving all the singular platform poses (singularity locus) and the mechanism geometric parameters are useful in the design of parallel mechanisms. This paper presents a new expression of the singularity condition of the most general mechanism (6-6 FPM) of a class of parallel mechanisms usually named fully-parallel mechanisms (FPM). The presented expression uses the mixed products of vectors that are easy to be identified on the mechanism. This approach will permit some singularities to be geometrically found. A procedure, based on this new expression, is provided to transform the singularity condition into a ninth-degree polynomial equation whose unknowns are the platform pose parameters. This singularity polynomial equation is cubic in the platform position parameters and a sixth-degree one in the platform orientation parameters. Finally, how to derive the expression of the singularity condition of a specific FPM from the presented 6-6 FPM singularity condition will be shown along with an example.

Singularity Analysis of Serial Robot-Manipulators

1996 ◽  
Vol 118 (4) ◽  
pp. 520-525 ◽  
Author(s):  
A. Karger
Keyword(s):  
Degrees Of Freedom ◽  
Robot Manipulator ◽  
Robot Manipulators ◽  
Singularity Analysis ◽  
Singular Set ◽  
Singular Configurations ◽  
Special Cases ◽  
Serial Robot ◽  
Singular Configuration ◽  
Actual Configuration

This paper is devoted to the description of the set of all singular configurations of serial robot-manipulators. For 6 degrees of freedom serial robot-manipulators we have developed a theory which allows to describe higher order singularities. By using Lie algebra properties of the screw space we give an algorithm, which determines the degree of a singularity from the knowledge of the actual configuration of axes of the robot-manipulator only. The local shape of the singular set in a neighbourhood of a singular configuration can be determined as well. We also solve the problem of escapement from a singular configuration. For serial robot-manipulators with the number of degrees of freedom different from six we show that up to certain exceptions singular configurations can be avoided by a small change of the motion of the end-effector. We also give an algorithm which allows to determine equations of the singular set for any serial robot-manipulator. We discuss some special cases and give examples of singular sets including PUMA 560.

Kinematic Calibration for Redundantly Actuated Parallel Mechanisms

2004 ◽  
Vol 126 (2) ◽  
pp. 307-318 ◽  
Author(s):  
Jay il Jeong ◽  
Dongsoo Kang ◽  
Young Man Cho ◽  
Jongwon Kim
Keyword(s):  
Optimization Algorithm ◽  
Parallel Mechanism ◽  
Kinematic Calibration ◽  
Parallel Mechanisms ◽  
Geometrical Constraint ◽  
Kinematic Parameters ◽  
Angle Error ◽  
Calibration Algorithm ◽  
Redundantly Actuated

We present a new kinematic calibration algorithm for redundantly actuated parallel mechanisms, and illustrate the algorithm with a case study of a planar seven-element 2-degree-of-freedom (DOF) mechanism with three actuators. To calibrate a nonredundantly actuated parallel mechanism, one can find actual kinematic parameters by means of geometrical constraint of the mechanism’s kinematic structure and measurement values. However, the calibration algorithm for a nonredundant case does not apply for a redundantly actuated parallel mechanism, because the angle error of the actuating joint varies with position and the geometrical constraint fails to be consistent. Such change of joint angle error comes from constraint torque variation with each kinematic pose (meaning position and orientation). To calibrate a redundant parallel mechanism, one therefore has to consider constraint torque equilibrium and the relationship of constraint torque to torsional deflection, in addition to geometric constraint. In this paper, we develop the calibration algorithm for a redundantly actuated parallel mechanism using these three relationships, and formulate cost functions for an optimization algorithm. As a case study, we executed the calibration of a 2-DOF parallel mechanism using the developed algorithm. Coordinate values of tool plate were measured using a laser ball bar and the actual kinematic parameters were identified with a new cost function of the optimization algorithm. Experimental results showed that the accuracy of the tool plate improved by 82% after kinematic calibration in a redundant actuation case.

scholarly journals Regularization of the Spatial Inverse Positioning Problem of Revolute Joint Manipulators

2017 ◽  
Vol 61 (3) ◽  
pp. 279
Author(s):  
Dániel András Drexler
Keyword(s):  
Inverse Kinematics ◽  
Closed Loop ◽  
Singular Values ◽  
Singular Configurations ◽  
Revolute Joints ◽  
Singular Direction ◽  
Inverse Kinematics Problem ◽  
Singular Configuration ◽  
Damped Least Squares ◽  
Kinematic Singularities

Inverse kinematics is a central problem in robotics, and its solution is burdened with kinematic singularities, i.e. the task Jacobian of the problem is singular. A subproblem of the general inverse kinematics problem, the inverse positioning problem is considered for spatial manipulators consisting of revolute joints, and a regularization method is proposed that results in a regular task Jacobian in singular configurations as well, provided that the manipulator’s geometry makes movement in singular directions possible. The conditions of regularizability are investigated, and bounds on the singular values of the regularized task Jacobian are given that can be used to create stable closed-loop inverse kinematics algorithms. The proposed method is demonstrated on the inverse positioning problem of an elbow manipulator and compared to the Damped Least Squares and the Levenberg-Marquardt methods, and it is shown that only the proposed method can leave the singular configuration in the singular direction.

A Comprehensive Numerical Study on the Number of Identifiable Kinematic Parameters of Parallel Mechanisms

2021 ◽  
Author(s):  
Lingyu Kong ◽  
Genliang Chen ◽  
Guanyu Huang ◽  
Sumian Song ◽  
Anhuan Xie ◽  
...  
Keyword(s):  
Numerical Study ◽  
Error Model ◽  
Error Modeling ◽  
Kinematic Error ◽  
Kinematic Calibration ◽  
Parallel Mechanisms ◽  
Kinematic Parameters ◽  
Positioning Accuracy ◽  
Prismatic Joints ◽  
Kinematic Error Model

Abstract Kinematic error model plays an important role in improving the positioning accuracy of robot manipulators by kinematic calibration. The identifiability of kinematic parameters in the error model directly affects the positioning accuracy of the mechanism. And the number of identifiable kinematic parameters determines how many parameters can be accurately identified by kinematic calibration, which is one of the theoretical basis of kinematic error modeling. For serial mechanisms, a consensus has been reached that the maximum number of identifiable kinematic parameters is 4R + 2P + 6, where R and P represent the numbers of revolute and prismatic joints, respectively. Due to complex topologies of parallel mechanisms, there is still no agreement on the formula of the maximum number of identifiable parameters. In this paper, a comprehensive numerical study on the number of identifiable kinematic parameters of parallel mechanisms is conducted. The number of identifiable parameters of 3802 kinds of limbs with different types or actuation arrangements are analyzed. It can be concluded that the maximum number of identifiable kinematic parameters is Σ i = 1 n 4Ri + 2Pi + 6 − Ci − 2(PP)i/3(PPP1)i/(2Ri + 2Pi)(PPP)i, where Ci represents the number of joints whose motion cannot be measured and n denotes the number of limbs in a parallel mechanism; (PP)i, (PPP1)i, and (PPP)i represent two consecutive unmeasurable P joints, three consecutive P joints in which two of them cannot be measured, and three unmeasurable P joints, respectively.

scholarly journals Generalized Singularity Analysis of Snake-Like Robot

2018 ◽  
Vol 8 (10) ◽  
pp. 1873 ◽  
Author(s):  
Shunsuke Nansai ◽  
Masami Iwase ◽  
Hiroshi Itoh
Keyword(s):  
Singularity Analysis ◽  
Common Point ◽  
Analysis Method ◽  
Link Length ◽  
New Model ◽  
Singular Configurations ◽  
Singular Configuration ◽  
The One

The purpose of this paper is to elucidate a generalized singularity analysis of a snake-like robot. The generalized analysis is denoted as analysis of singularity of a model which defines all designable parameters such as the link length and/or the position of the passive wheel as arbitrary variables. The denotation is a key point for a novelty of this study. This paper addresses the above new model denotation, while previous studies have defined the designable parameters as unique one. This difference makes the singularity analysis difficult substantively. To overcome this issue, an analysis method using redundancy of the snake-like robot is proposed. The proposed method contributes to simplify singularity analysis concerned with the designable parameters. The singular configurations of both the model including side-slipping and the one with non side-slipping are analyzed. As the results of the analysis, we show two contributions. The first contribution is that a singular configuration depends on designable parameters such as link length as well as state values such as relative angles. The second contribution is that the singular configuration is characterized by the axials of the passive wheels of all non side-slipping link. This paper proves that the singular configuration is identified as following two conditions even if the designable parameters are chosen as different variables and the model includes side-slipping link. One is that the axials of passive wheels of all non side-slipping links intersect at a common point. Another one is that axials of passive wheels of all non side-slipping links are parallel.

Sign in / Sign up

Export Citation Format

Share Document