A Methodology to Experimentally Investigate the Impact of Wobble Errors on the Contact Pattern and Static Transmission Error of Helical Gear Pairs

2019 ◽  
Author(s):  
Michael Benatar ◽  
Michael Handschuh ◽  
Ahmet Kahraman ◽  
David Talbot
Keyword(s):  
Transmission Error ◽  
Helical Gear ◽  
Experimental Results ◽  
Gear Pair ◽  
Contact Pattern ◽  
Gear Mesh ◽  
Face Width ◽  
The Face ◽  
Static Transmission Error ◽  
The Impact

Abstract For a gear pair, both the contact pattern and the transmission error (TE) significantly impact durability and fatigue life. Design and manufacturing processes are often aimed at improving the contact pattern and reducing the overall TE. Other errors, such as runout and wobble, are often induced during the installation of power transmission systems, and they can alter the contact pattern and TE of an otherwise well-designed gear pair. This study provides a methodology to experimentally investigate the impact of wobble errors on the contact pattern and static transmission error (STE) of helical gears. It first provides a description of the modifications to an existing test machine. Next, it describes the gear specifications, preliminary testing matrix, data acquisition and processing procedure, as well as the experimental results obtained with regards to both the contact pattern and STE. The following are observed while describing the experimental results. For a test with no wobble and no runout, the contact pattern remains the same at every rotational position. However, by introducing even a small amount of wobble, the contact will shift from one side of the face width of the gear to the opposite side of the face width of the gear within one revolution. Introduction of wobble may increase the STE and sideband activity around gear mesh harmonics, especially as torque increases. Yet the modest increases in STE and sideband activity seen with the introduction of wobble are not enough to make definitive conclusions. The feasibility of the modified test setup has been demonstrated, and preliminary results have been presented. However, additional data collection should be completed in order to study the impact of runout and wobble on both spur and helical gear pairs with various microgeometry modifications and manufacturing errors.

Effect of Axial Vibrations on the Dynamics of a Helical Gear Pair

1993 ◽  
Vol 115 (1) ◽  
pp. 33-39 ◽  
Author(s):  
A. Kahraman
Keyword(s):  
Natural Frequencies ◽  
Helix Angle ◽  
Transmission Error ◽  
Helical Gear ◽  
Forced Response ◽  
Dynamic Mesh ◽  
Gear Pair ◽  
Gear Mesh ◽  
Static Transmission Error ◽  
Helical Gear Pair

In this paper, a linear dynamic model of a helical gear pair has been developed. The model accounts for the shaft and bearing flexibilities, and the dynamic coupling among the transverse, torsional, axial and rotational (rocking) motions due to the gear mesh. The natural frequencies and the mode shapes have been predicted, and the modes which are excited by the static transmission error have been identified. The forced response due to the static transmission error has also been predicted, including the dynamic mesh and bearing forces. A parametric study has been performed to investigate the effect of the helix angle on the free and forced vibrational characteristics of the gear pair. It has been shown that the helix angle can be neglected in predicting the natural frequencies and the dynamic mesh forces. An accurate prediction of dynamic bearing forces and moments requires inclusion of the helix angle in the analysis.

Effect of Axial Vibrations on the Dynamics of a Helical Gear Pair

1991 ◽  
Author(s):  
Ahmet Kahraman
Keyword(s):  
Natural Frequencies ◽  
Helix Angle ◽  
Transmission Error ◽  
Helical Gear ◽  
Forced Response ◽  
Dynamic Mesh ◽  
Gear Pair ◽  
Gear Mesh ◽  
Static Transmission Error ◽  
Helical Gear Pair

Abstract In this paper, a linear dynamic model of a helical gear pair has. been developed. The model accounts for the shaft and bearing flexibilities, and the dynamic coupling among the transverse, torsional, axial and rotational motions because of the gear mesh. The natural frequencies and the mode shapes have been predicted, and the modes which are excited by the static transmission error have been identified. The forced response due to the static transmission error has also been predicted, including the dynamic mesh and bearing forces. A parametric study has been performed to investigate the effect of the helix angle on the free and forced vibrational characteristics of the gear pair. It has been shown that the helix angle can be neglected in predicting the natural frequencies and the dynamic mesh forces. An accurate prediction of dynamic bearing forces and moments requires inclusion of helix angle in the analysis.

Dynamic Analysis of a Multi-Mesh Helical Gear Train

1992 ◽  
Author(s):  
Ahmet Kahraman
Keyword(s):  
Loading Condition ◽  
Helix Angle ◽  
Transmission Error ◽  
Helical Gear ◽  
Forced Response ◽  
Gear Train ◽  
Loading Conditions ◽  
Gear Mesh ◽  
Natural Modes ◽  
Static Transmission Error

Abstract In this paper, the dynamic behavior of a multi-mesh helical gear train is studied. The gear train consists of three helical gears, with one of the gears in mesh with the other two. An 18-degree-of-freedom dynamic model which includes transverse, torsional, axial and rotational (rocking) motions of the flexibly mounted gears is developed. Two different loading conditions are identified. For case I, the system is driven by the gear in the middle, and for case II, the system is driven by one of the gears at either end of the gear train. Gear mesh phases under each loading condition are determined. The natural modes are predicted, and effects of the helix angle and the loading condition on the natural modes are explained. The forced response, which includes dynamic mesh and bearing forces, due to the static transmission error excitation is found. Effects of loading conditions and asymmetric positioning on the response are also explored. The results suggest that the dynamic forces are lower if the number of teeth of the gear in the middle is (i) an odd number for case I type loading, and (ii) an even number for case II type loading.

scholarly journals Geometry Modification of Helical Gear for Reduction of Static Transmission Error

2018 ◽  
Vol 167 ◽  
pp. 02013
Author(s):  
Jeonghyun Park ◽  
Changjun Seo ◽  
Kwangsuck Boo ◽  
Heungseob Kim
Keyword(s):  
Transmission Error ◽  
Helical Gear ◽  
Necessary Condition ◽  
Mesh Stiffness ◽  
Profile Modification ◽  
Gear Mesh ◽  
Static Transmission Error ◽  
Excitation Mechanisms ◽  
Gear Systems ◽  
Gear Mesh Stiffness

Gear systems are extensively employed in mechanical systems since they allow the transfer of power with a variety of gear ratios. So gears cause the inherent deflections and deformations due to the high pressure which occurs between the meshing teeth when transmit power and results in the transmission error. It is usually assumed that the transmission error and variation of the gear mesh stiffness are the dominant excitation mechanisms. Predicting the static transmission error is a necessary condition to reduce noise radiated from the gear systems. This paper aims to investigate the effect of tooth profile modifications on the transmission error of helical gear. The contact stress analysis was implemented for different roll positions to find out the most critical roll angle in view point of root flank stress. The PPTE (peak-to-peak of transmission error) is estimated at the roll angles by different loading conditions with two dimensional FEM. The optimal profile modification from the root to the tip is proposed.

Tooth Root Stresses of Helical Gear Pairs With Unequal and Offset Face Widths

2011 ◽  
Author(s):  
Carlos H. Wink
Keyword(s):  
Load Distribution ◽  
Element Model ◽  
Helical Gear ◽  
The Other ◽  
Gear Pair ◽  
Tooth Root ◽  
Pair Member ◽  
Face Width ◽  
The Face ◽  
Root Stress

In this study, tooth root stresses of helical gear pairs with different combinations of face width increase and offsets were analyzed. Contact face width was kept constant. The variables studied were face width and gear faces offset. The well-known LDP – Load Distribution Program was used to calculate tooth root stresses using a finite element model. The results presented show that the face width increase and offset have a significant influence on tooth root stresses. In some cases, increasing face width of one gear pair member resulted in significant increase of tooth root stress of the other member. For gear pairs with unequal and offset face widths, tooth root stresses were mostly affected when face widths were increased to the same direction of the contact line travel direction.

Using variable modulus to modify a rack cutter and generate a gear pair

2022 ◽  
pp. 095440622110617
Author(s):  
Yang Hsueh-Cheng ◽  
Zhong-Wei Huang
Keyword(s):  
Helical Gear ◽  
Tooth Surface ◽  
Gear Pair ◽  
Tooth Contact Analysis ◽  
Parabolic Profile ◽  
Face Width ◽  
Variable Modulus ◽  
The Face ◽  
Helical Gear Pair ◽  
Assembly Error

In this paper, two normal imaginary helical rack cutters were first established. One of these cutters is a skewed-rack cutter with an asymmetrical straight edge. The other is a rack cutter with an asymmetric parabolic profile. Second, the gear’s tooth surface of the asymmetric parabolic rack cutter is modified to be barrel-shaped based on a variable modulus. The tooth thickness of the gear is gradually reduced along the face width of the tooth from the middle of the tooth surface. Then the coordinate relationship between the gears’ blanks and the imaginary helical rack cutters was established. Through the differential geometry, crowned and uncrowned helical gear pairs were generated. Because of human factors, when the gear pair is installed, it is easy to cause the gear pair edge contact. It is necessary to add artificial assembly error settings through the tooth contact analysis to investigate the kinematic errors and contact conditions of the crowned and uncrowned helical gear pair. The mathematical models and analysis methods proposed for the crowned imaginary rack cutter using variable modulus should be useful for the design and production of double crowned helical gears with asymmetric parabolic teeth.

Static and Dynamic Transmission Error Measurements of Helical Gear Pairs With Various Tooth Modifications

2019 ◽  
Vol 141 (10) ◽  
Author(s):  
M. Benatar ◽  
M. Handschuh ◽  
A. Kahraman ◽  
D. Talbot
Keyword(s):  
Dynamic Models ◽  
Nonlinear Behavior ◽  
Transmission Error ◽  
Helical Gear ◽  
Forced Response ◽  
Test Machine ◽  
Response Curves ◽  
Gear Mesh ◽  
Dynamic Transmission Error ◽  
Static Transmission Error

This paper presents a set of motion transmission error data for a family of helical gears having different profile and lead modifications operated under both low-speed (quasi-static) and dynamic conditions. A power circulatory test machine is used along with encoder and accelerometer-based transmission error measurement systems to quantify motion transmission behavior within wide ranges of torque and speed. Results of these experiments indicate that the tooth modifications impact the resultant static and dynamic transmission error amplitudes significantly. A design load is shown to exist for each gear pair of different modifications where static transmission error amplitude is minimum. Forced response curves and waterfall plots are presented to demonstrate that the helical gear pairs tested act linearly with no signs of nonlinear behavior such as tooth contact separations. Furthermore, static and dynamic transmission error amplitudes are observed to be nearly proportional, suggesting that static transmission error can be employed in helical gear dynamic models as the main gear mesh excitation. The data presented here is intended to fill a void in the literature by providing means for validation of load distribution and dynamic models of helical gear pairs.

Utilization of Tooth Contact Pattern in a Gear Meshing Model for Estimation of Sliding Loss in a Parallel-Axis Gear Pair

2014 ◽  
Vol 619 ◽  
pp. 68-72
Author(s):  
Jetsada Phraeknanthoe ◽  
Natcha Ponchai ◽  
Chanat Ratanasumawong
Keyword(s):  
Helix Angle ◽  
Helical Gear ◽  
Experimental Results ◽  
Gear Pair ◽  
Contact Pattern ◽  
Tooth Contact ◽  
Parallel Axis ◽  
Helical Gear Pair

The utilization of tooth contact pattern in a gear meshing model for estimation of sliding loss in a spur and helical gear pair is presented in this paper. The photo of tooth contact pattern taken after the gear operation is used as the database to generate the simplified tooth contact pattern. Then the simplified contact pattern is used along with the gear meshing model to estimate the sliding loss of a gear pair. Experiments are done to verify the results. The estimated results from the presented method agree well with the experimental results. The presented method is able to estimate the effect of the helix angle on the sliding loss correctly whereas the estimation without using the data of tooth contact pattern cannot.

Transmission Error as Gear Noise Excitation

2009 ◽  
Author(s):  
Mats Henriksson ◽  
Yuet-Yan Pang
Keyword(s):  
Transmission Error ◽  
Gear Pair ◽  
Bending Moments ◽  
Contact Pattern ◽  
Gear Noise ◽  
Correlate Noise ◽  
Edge Contact ◽  
Measurement Result ◽  
Static Transmission Error ◽  
The Difference

Traditionally, transmission error (TE) has been used in order to asses the noise properties of gears. Measurements of gear noise for a complete truck gearbox have been used to correlate noise from a gear pair with the concept of calculated static transmission error as noise excitation. Two gear pairs with very similar macro geometry but different micro geometry was used. Both transmission error as excitation and the excitation proposed by P. Velex and M. Ajmi which is the difference between the loaded and unloaded transmission error, are compared with measured noise. The result shows that the difference between the loaded and unloaded TE correlates well with measure noise for gear pair A but no excitation correlates with the measurement result gear pair B. A big difference between gear pair A and B can be seen in the contact pattern. The contact pattern of gear pair B shows that despite a large tip relief, edge contact occurs where the tip relief starts. This can be one explanation to the lack of correlation between TE and the measurement result for gear pair B. Another explanation can be other excitations such as friction and bending moments. The results show the limitations of only considering transmission error when designing quiet gears.

An Investigation of the Influence of Shaft Misalignments on Bending Stresses of Helical Gear With Lead Crown

2007 ◽  
Author(s):  
M. A. Hotait ◽  
D. Talbot ◽  
A. Kahraman
Keyword(s):  
Load Distribution ◽  
Helical Gear ◽  
Experimental Results ◽  
Distribution Model ◽  
Strain Gauges ◽  
Gear Teeth ◽  
Face Width ◽  
The Face ◽  
Bending Stresses ◽  
Different Levels

In this study, combined influence of shaft misalignments and gear lead crown on the load distribution and tooth bending stresses is investigated experimentally. A set of helical gear pairs having various amounts of lead crown was tested under loaded, low-speed conditions with varying amounts of tightly-controlled shaft misalignments. Gear teeth were instrumented through strips of strain gauges along the face width of gears at the tooth fillet region near the start of active profile. Variations of root strains along the face width were recorded for different levels of shaft misalignments and gear lead crown. At the end, the experimental results were correlated to the predictions of a gear load distribution model and recommendations were made on how much lead crown is optimal for a given misalignment condition.

Sign in / Sign up

Export Citation Format

Share Document