Merging Near-Wall RANS Models With LES for Separating and Reattaching Flows

2006 ◽  
Author(s):  
Suad Jakirlic´ ◽  
Bjo¨rn Kniesner ◽  
Sanjin Sˇaric´ ◽  
Kemal Hanjalic´
Keyword(s):  
Reynolds Number ◽  
Equation Model ◽  
Navier Stokes ◽  
Model Parameters ◽  
Wall Region ◽  
Detached Eddy Simulation ◽  
Rans Model ◽  
Eddy Simulation ◽  
Moderate Reynolds Number ◽  
Near Wall

A method of coupling a low-Reynolds-number k–ε RANS (Reynolds-Averaged Navier-Stokes) model with Large-Eddy Simulation (LES) in a two-layer Hybrid LES/RANS (HLR) scheme is proposed in the present work. The RANS model covers the near-wall region and the LES model the remainder of the flow domain. Two different subgrid-scale (SGS) models in LES were considered, the Smagorinsky model and the one-equation model for the residual kinetic energy (Yoshizawa and Horiuti, 1985), combined with two versions of the RANS ε equation, one governing the “isotropic” (ε˜; Chien, 1982) and the other the “homogeneous” dissipation rate (εh; Jakirlic and Hanjalic, 2002). Both fixed and self-adjusting interface locations were considered. The exchange of the variables across the interface was adjusted by smoothing the turbulence viscosity either by adjusting the RANS model parameters, such as Cμ (Temmerman et al., 2005), or by applying an additional forcing at the interface using a method of digital-filter-based generation of inflow data for spatially developing DNS and LES due to Klein et al. (2003). The feasibility of the method was illustrated against the available DNS, fine- and coarse grid LES, DES (Detached Eddy Simulation) and experiments in turbulent flow over a backward-facing step at a low (Yoshioka et al., 2001) and a high Re number (Vogel and Eaton, 1985), periodic flow over a series of 2-D hills (Fro¨hlich et al., 2005) and in a high-Re flow over a 2-D, wall-mounted hump (Greenblat et al, 2004). Prior to these computations, the method was validated in a fully-developed channel flow at a moderate Reynolds number Rem ≈ 24000 (Abe et al., 2004).

An Anisotropic Subgrid Model for Large Eddy Simulation of Wall Bounded Turbulent Flows

2007 ◽  
Author(s):  
Sachin S. Badarayani ◽  
Kyle D. Squires
Keyword(s):  
Reynolds Number ◽  
Large Eddy Simulation ◽  
Velocity Profile ◽  
Turbulent Flows ◽  
Model Parameters ◽  
Wall Region ◽  
Outer Flow ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Near Wall

Large Eddy Simulation (LES) of high-Reynolds-number wall-bounded turbulent flows is prohibitively expensive if the energy-containing eddies in the near-wall region are resolved. This motivates the use of wall-layer models in which an approximate solution of the near wall dynamics is bridged to an LES of the outer flow. The main interest of the present work are wall-modeling strategies based on Detached Eddy Simulation (DES). In these approaches, the near-wall solution is closed using a Reynolds-averaged Navier Stokes model with a subgrid closure applied to the outer flow. As is well known, the original DES formulation applied directly as a wall model results in a shift in the velocity profile, corresponding to an under-estimation of the skin friction. A new formulation is proposed in this contribution in which the wall-parallel components of the modeled stress are reduced in order to lower the influence of the model and increase the resolved stress. The effectiveness of the new model is evaluated via comparison against DES predictions using the original and recently-proposed versions of the method. The effect of grid resolution and model parameters are also assessed using computations of turbulent channel flow at a Reynolds number based on friction velocity and channel halfwidth of 5000. The predictions show that the anisotropic form of the model stress yields an improved prediction of the mean velocity profile in better agreement with the logarithmic law and with larger resolved stress in the near-wall region.

Simulating flow separation from continuous surfaces: routes to overcoming the Reynolds number barrier

2009 ◽  
Vol 367 (1899) ◽  
pp. 2885-2903 ◽  
Author(s):  
Michael Leschziner ◽  
Ning Li ◽  
Fabrizio Tessicini
Keyword(s):  
Reynolds Number ◽  
Turbulent Flows ◽  
Major Elements ◽  
Wall Layer ◽  
Navier Stokes ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Rans Models ◽  
High Reynolds ◽  
Near Wall

This paper provides a discussion of several aspects of the construction of approaches that combine statistical (Reynolds-averaged Navier–Stokes, RANS) models with large eddy simulation (LES), with the objective of making LES an economically viable method for predicting complex, high Reynolds number turbulent flows. The first part provides a review of alternative approaches, highlighting their rationale and major elements. Next, two particular methods are introduced in greater detail: one based on coupling near-wall RANS models to the outer LES domain on a single contiguous mesh, and the other involving the application of the RANS and LES procedures on separate zones, the former confined to a thin near-wall layer. Examples for their performance are included for channel flow and, in the case of the zonal strategy, for three separated flows. Finally, a discussion of prospects is given, as viewed from the writer's perspective.

Detached-Eddy Simulations Over a Simplified Landing Gear

2002 ◽  
Vol 124 (2) ◽  
pp. 413-423 ◽  
Author(s):  
L. S. Hedges ◽  
A. K. Travin ◽  
P. R. Spalart
Keyword(s):  
Stokes Equations ◽  
Separated Flow ◽  
Flow Fields ◽  
Equation Model ◽  
Landing Gear ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
Navier Stokes Equations ◽  
Instantaneous Flow ◽  
Eddy Simulation

The flow around a generic airliner landing-gear truck is calculated using the methods of Detached-Eddy Simulation, and of Unsteady Reynolds-Averaged Navier-Stokes Equations, with the Spalart-Allmaras one-equation model. The two simulations have identical numerics, using a multi-block structured grid with about 2.5 million points. The Reynolds number is 6×105. Comparison to the experiment of Lazos shows that the simulations predict the pressure on the wheels accurately for such a massively separated flow with strong interference. DES performs somewhat better than URANS. Drag and lift are not predicted as well. The time-averaged and instantaneous flow fields are studied, particularly to determine their suitability for the physics-based prediction of noise. The two time-averaged flow fields are similar, though the DES shows more turbulence intensity overall. The instantaneous flow fields are very dissimilar. DES develops a much wider range of unsteady scales of motion and appears promising for noise prediction, up to some frequency limit.

On the Investigation of Flow around the Square Cylinder Based on Different LES Models

2012 ◽  
Vol 594-597 ◽  
pp. 2676-2679
Author(s):  
Zhe Liu
Keyword(s):  
Flow Characteristics ◽  
Turbulence Models ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
Square Cylinder ◽  
Rans Model ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Reynolds Averaged Navier Stokes ◽  
Les Model

Although the conventional Reynolds-averaged Navier–Stokes (RANS) model has been widely applied in the industrial and engineering field, it is worthwhile to study whether these models are suitable to investigate the flow filed varying with the time. With the development of turbulence models, the unsteady Reynolds-averaged Navier–Stokes (URANS) model, detached eddy simulation (DES) and large eddy simulation (LES) compensate the disadvantage of RANS model. This paper mainly presents the theory of standard LES model, LES dynamic model and wall-adapting local eddy-viscosity (WALE) LES model. And the square cylinder is selected as the research target to study the flow characteristics around it at Reynolds number 13,000. The influence of different LES models on the flow field around the square cylinder is compared.

Numerical investigation of vortex-induced vibration of an elastically mounted circular cylinder with One-degree of freedom at high Reynolds number using different turbulent models

2018 ◽  
Vol 233 (2) ◽  
pp. 443-453 ◽  
Author(s):  
Niaz Bahadur Khan ◽  
Zainah Ibrahim
Keyword(s):  
Reynolds Number ◽  
Flow Direction ◽  
Cross Flow ◽  
Navier Stokes ◽  
Two Dimensional ◽  
Detached Eddy Simulation ◽  
Eddy Simulation ◽  
Flow Around Cylinder ◽  
Reynolds Averaged Navier Stokes ◽  
Turbulent Models

This study presents numerical investigation for flow around cylinder at Reynolds number = 104 using different turbulent models. Numerical simulations have been conducted for fixed cylinder case at Reynolds number = 104 and for cylinder free to oscillate in cross-flow direction, at Reynolds number O (104), mass–damping ratio = 0.011 and range of frequency ratio wt = 0.4–1.4 using two-dimensional Reynolds-averaged Navier–Stokes equations. In the literature, the study has been conducted using detached eddy simulation, large eddy simulation and direct numerical simulation which are comparatively expensive in terms of computational cost. This study utilizes the Reynolds-averaged Navier–Stokes shear stress transport k-ω and realizable k-ε models to investigate the flow around fixed cylinder and flow around cylinder constrained to oscillate in cross-flow direction only. Hydrodynamic coefficients, vortex mode shape and maximum amplitude ( Ay/ D) extracted from this study are compared with detached eddy simulation, large eddy simulation and direct numerical simulation results. Results obtained using two-dimensional Reynolds-averaged Navier–Stokes shear stress transport k-ω model are encouraging, while realizable k-ε model is unable to capture the entire response branches. In addition, broad range of “lock-in” region is observed due to delay in capturing the transition from upper to lower branch during two-dimensional realizable k-ε analyses.

Numerical study of the flow over the modified simple frigate shape

2020 ◽  
pp. 095441002097775
Author(s):  
Tong Li ◽  
Yibin Wang ◽  
Ning Zhao
Keyword(s):  
Bluff Body ◽  
Recirculation Zone ◽  
Numerical Study ◽  
Reference Value ◽  
Flow Fields ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation ◽  
Simulation Results

The simple frigate shape (SFS) as defined by The Technical Co-operative Program (TTCP), is a simplified model of the frigate, which helps to investigate the basic flow fields of a frigate. In this paper, the flow fields of the different modified SFS models, consisting of a bluff body superstructure and the deck, were numerically studied. A parametric study was conducted by varying both the superstructure length L and width B to investigate the recirculation zone behind the hangar. The size and the position of the recirculation zones were compared between different models. The numerical simulation results show that the size and the location of the recirculation zone are significantly affected by the superstructure length and width. The results obtained by Reynolds-averaged Navier-Stokes method were also compared well with both the time averaged Improved Delayed Detached-Eddy Simulation results and the experimental data. In addition, by varying the model size and inflow velocity, various flow fields were numerically studied, which indicated that the changing of Reynolds number has tiny effect on the variation of the dimensionless size of the recirculation zone. The results in this study have certain reference value for the design of the frigate superstructure.

Detached Eddy Simulation of Transonic Rotor Stall Flutter Using a Fully Coupled Fluid-Structure Interaction

2011 ◽  
Author(s):  
Hongsik Im ◽  
Xiangying Chen ◽  
Gecheng Zha
Keyword(s):  
Stokes Equations ◽  
Rotating Stall ◽  
Rotor Blades ◽  
Tip Clearance ◽  
Weno Scheme ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
Eddy Simulation ◽  
Stall Flutter ◽  
Fully Coupled

Detached eddy simulation of an aeroelastic self-excited instability, flutter in NASA Rotor 67 is conducted using a fully coupled fluid/structre interaction. Time accurate compressible 3D Navier-Stokes equations are solved with a system of 5 decoupled modal equations in a fully coupled manner. The 5th order WENO scheme for the inviscid flux and the 4th order central differencing for the viscous flux are used to accurately capture interactions between the flow and vibrating blades with the DES (detached eddy simulation) of turbulence. A moving mesh concept that can improve mesh quality over the rotor tip clearance was implemented. Flutter simulations were first conducted from choke to stall using 4 blade passages. Stall flutter initiated at rotating stall onset, grows dramatically with resonance. The frequency analysis shows that resonance occurs at the first mode of the rotor blade. Before stall, the predicted responses of rotor blades decayed with time, resulting in no flutter. Full annulus simulation at peak point verifies that one can use the multi-passage approach with periodic boundary for the flutter prediction.

Numerical Investigation of Energy Saving Device Effects on Ships With Propeller-Hull Interactions

2018 ◽  
Author(s):  
Ravi Chaithanya Mysa ◽  
Le Quang Tuyen ◽  
Ma Shengwei ◽  
Vinh-Tan Nguyen
Keyword(s):  
Energy Saving ◽  
Full Scale ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
Propulsion Efficiency ◽  
Operational Conditions ◽  
Ship Resistance ◽  
The Past ◽  
Eddy Simulation ◽  
Flow Features

Energy saving devices (ESD) such as propeller ducts, pre-swirl stators, pre-nozzles, etc have been explored as a more economic and reliable approach to reduce energy consumption for both in-operation and newly design ships over the past decades. Those energy saving devices work in the principle of reducing ship resistance and improving propulsion efficiency as well as hull-propeller interactions. Potential saving from various types of ESD have been reported in literature from the range of 3–9% [1] for propulsion efficiency dependent on different measures. Deployment of those devices on actual full-scale ships has been limited over the past years. One of the key obstacles in application of ESD is the lack of confidence in measuring its efficiency on full-scale ships in actual operational conditions. Advances in computational fluid dynamics (CFD) has provided an alternative approach from model scale test to better understand uncertainties in prediction of ESD efficiency in full-scale ship operations [Shin et al, 2013]. In this work a high fidelity CFD model is presented for investigation effects of pre-nozzles on propulsion efficiency and ship resistance. The model is based on the Reynolds Average Navier-Stokes (RANS) solver with different turbulent models including a hybrid detached eddy simulation (DES) approach for predictions of complex near body flow features as well as in the wake regions from hull and propeller. The model is validated with model test for both towing and self-propulsion conditions. Finally a study of pre-nozzle effects on propeller efficiency as well as hull-propeller interaction is presented and compared with available experimental data (Tokyo 2015 Workshop). The current work constitutes a fundamental approach towards designing more efficient ESD for a specific hull form and propeller.

Large-eddy simulations of tip leakage and secondary flows in an axial compressor cascade using a near-wall turbulence model

2009 ◽  
Vol 223 (6) ◽  
pp. 645-655 ◽  
Author(s):  
D Borello ◽  
G Delibra ◽  
K Hanjalić ◽  
F Rispoli
Keyword(s):  
Secondary Flows ◽  
Tip Clearance ◽  
Navier Stokes ◽  
Wall Region ◽  
Compressor Cascade ◽  
Tip Leakage ◽  
Computational Mesh ◽  
Large Eddy ◽  
Reynolds Averaged Navier Stokes ◽  
Near Wall

This paper reports on the application of unsteady Reynolds averaged Navier—Stokes (U-RANS) and hybrid large-eddy simulation (LES)/Reynolds averaged Navier—Stokes (RANS) methods to predict flows in compressor cascades using an affordable computational mesh. Both approaches use the ζ— f elliptic relaxation eddy-viscosity model, which for U-RANS prevails throughout the flow, whereas for the hybrid the U-RANS is active only in the near-wall region, coupled with the dynamic LES in the rest of the flow. In this ‘seamless’ coupling the dissipation rate in the k-equation is multiplied by a grid-detection function in terms of the ratio of the RANS and LES length scales. The potential of both approaches was tested in several benchmark flows showing satisfactory agreement with the available experimental results. The flow pattern through the tip clearance in a low-speed linear cascade shows close similarity with experimental evidence, indicating that both approaches can reproduce qualitatively the tip leakage and tip separation vortices with a relatively coarse computational mesh. The hybrid method, however, showed to be superior in capturing the evolution of vortical structures and related unsteadiness in the hub and wake regions.

Sign in / Sign up

Export Citation Format

Share Document