Performance of Supercritical Slurry Jet Drilling System

2017 ◽  
Author(s):  
Ashwin Padsalgikar ◽  
Ramin Dabirian ◽  
Ken Oglesby ◽  
Ram S. Mohan ◽  
Ovadia Shoham
Keyword(s):  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Target Material ◽  
Nozzle Geometry ◽  
Experimental Program ◽  
Driving Mechanism ◽  
Flow Ratio ◽  
Drilling System ◽  
Driller System

A slurry jet driller is a novel drilling method, which delivers an abrasive slurry and supercritical gas mixture, to an expander nozzle. The expanded fluids flowing out of the nozzle, energize the particles, which hit the target material and erode it, achieving drilling. The expansion of the gas from a super critical state to in situ pressure and temperature conditions is the driving mechanism of the drilling operation. The primary objective of this paper is to evaluate the feasibility of the novel slurry jet drilling system. An experimental program is carried out for testing the performance of a slurry jet driller. The slurry is formed by mixing water with garnet particles, and a super critical carbon dioxide as the gas phase. The purpose of experiments is to evaluate the erosive nature of garnet rocks and to test the cutting efficiency of the nozzle. The acquired data show that the material removal rate increases with increase in the gas-slurry flow ratio, until a ratio of 1.5. A further increase in the flow ratio results in a reduction of the rate of material removal. Improved nozzle geometry was obtained using a program written in MATLAB. Criteria used for geometry improvement was the force applied to the bottom of the drilled bore. A rudimentary model is developed for the prediction of material removal rate utilizing a slurry jet driller, which is presented in a dimensionless form. The model incorporates the important variables affecting the jet driller system performance, including fluid and target material properties, and particle velocity. A fair agreement is observed between model predictions and experimental data, exhibiting a 20% deviation.

Effects of Non-Electrical Parameters on Material Removal Rate of High-Speed Small Hole EDM Drilling

2008 ◽  
Vol 53-54 ◽  
pp. 403-407 ◽  
Author(s):  
Ming Rang Cao ◽  
Y.Q. Wang ◽  
Shi Chun Yang ◽  
Sheng Qiang Yang ◽  
Wen Hui Li
Keyword(s):  
Material Removal Rate ◽  
Material Removal ◽  
High Speed ◽  
Removal Rate ◽  
Small Hole ◽  
Manufacturing Processes ◽  
Electrical Parameters ◽  
Drilling System ◽  
Edm Drilling ◽  
Selection Of

The selection of manufacturing conditions is very important in manufacturing processes as these ones determine the material removal rate (MRR) of the so-obtained parts. So in this paper, based on the brief introduction of the experimental principle and the high-speed small hole EDM drilling system, effects of non-electrical parameters on MRR are discussed in detail. The relationships between MRR and these factors are also analyzed. The conclusion can provide an important reference for production in practice.

Deep Profiled Slot Grinding on a Nickel-Based Alloy with Electroplated CBN Wheels

2016 ◽  
Vol 1136 ◽  
pp. 3-8 ◽  
Author(s):  
Zhong De Shi ◽  
Amr Elfizy ◽  
Helmi Attia
Keyword(s):  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Cubic Boron Nitride ◽  
Ground Surface ◽  
Target Material ◽  
Machined Surface ◽  
Turbine Disks ◽  
Nickel Based Alloy ◽  
Grinding Power

A process for grinding deep profiled slots in a nickel-based alloy with electroplated cubic boron nitride (CBN) wheels and straight oil is presented. These slots were prepared by this process for further grinding with electroplated CBN quills to generate the final fir-tree slots in gas turbine disks. Fir-tree slots are usually machined using broaching. The application of broaching, however, is limited in the case of nickel-based powder metal alloys due to short life of broaching tools and the effect on machined surface integrity. Grinding tests were first conducted on rectangular blocks to grind slots without inclinations at a fixed wheel speed vs = 60 m/s to identify the combinations of depths of cut, workspeed, and up/down grinding satisfying the requirements of ground surface quality and material removal rate. Inclined slots were then ground with the identified condition on a block representing a segment of an actual turbine disk to validate the condition. The wheel life was finally tested by grinding all the slots on the actual disk. Grinding power was measured, and the ground surfaces were inspected for any sign of burning. Preset target material removal rate and wheel life were obtained. It was found that electroplated CBN wheels are capable of grinding deep profiled slots on the difficult-to-cut nickel-based alloy.

Effects of Process Parameters on Surface Roughness and MRR in the hard turning of EN 36 steel

2018 ◽  
pp. 102-110
Author(s):  
Amritpal Singh ◽  
Rakesh Kumar
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Hard Turning ◽  
Control Parameter ◽  
Removal Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Dry Cutting

In the present study, Experimental investigation of the effects of various cutting parameters on the response parameters in the hard turning of EN36 steel under the dry cutting condition is done. The input control parameters selected for the present work was the cutting speed, feed and depth of cut. The objective of the present work is to minimize the surface roughness to obtain better surface finish and maximization of material removal rate for better productivity. The design of experiments was done with the help of Taguchi L9 orthogonal array. Analysis of variance (ANOVA) was used to find out the significance of the input parameters on the response parameters. Percentage contribution for each control parameter was calculated using ANOVA with 95 % confidence value. From results, it was observed that feed is the most significant factor for surface roughness and the depth of cut is the most significant control parameter for Material removal rate.

Performance Analysis of Trihexyltetradecylphosphonium Chloride Ionic Fluid under MQL Condition in Hard turning

2020 ◽  
Vol 17 (1) ◽  
pp. 7629-7647
Author(s):  
A. Pandey ◽  
R. Kumar ◽  
A. K. Sahoo ◽  
A. Paul ◽  
A. Panda
Keyword(s):  
Material Removal Rate ◽  
Feed Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Cutting Speed ◽  
Coconut Oil ◽  
Chip Morphology ◽  
Weight Fraction ◽  
Cutting Fluid ◽  
Depth Of Cut

The current research presents an overall performance-based analysis of Trihexyltetradecylphosphonium Chloride [[CH3(CH2)5]P(Cl)(CH2)13CH3] ionic fluid mixed with organic coconut oil (OCO) during turning of hardened D2 steel. The application of cutting fluid on the cutting interface was performed through Minimum Quantity Lubrication (MQL) approach keeping an eye on the detrimental consequences of conventional flood cooling. PVD coated (TiN/TiCN/TiN) cermet tool was employed in the current experimental work. Taguchi’s L9 orthogonal array and TOPSIS are executed to analysis the influences, significance and optimum parameter settings for predefined process parameters. The prime objective of the current work is to analyze the influence of OCO based Trihexyltetradecylphosphonium Chloride ionic fluid on flank wear, surface roughness, material removal rate, and chip morphology. Better quality of finish (Ra = 0.2 to 1.82 µm) was found with 1% weight fraction but it is not sufficient to control the wear growth. Abrasion, chipping, groove wear, and catastrophic tool tip breakage are recognized as foremost tool failure mechanisms. The significance of responses have been studied with the help of probability plots, main effect plots, contour plots, and surface plots and the correlation between the input and output parameters have been analyzed using regression model. Feed rate and depth of cut are equally influenced (48.98%) the surface finish while cutting speed attributed the strongest influence (90.1%). The material removal rate is strongly prejudiced by cutting speed (69.39 %) followed by feed rate (28.94%) whereas chip reduction coefficient is strongly influenced through the depth of cut (63.4%) succeeded by feed (28.8%). TOPSIS significantly optimized the responses with 67.1 % gain in closeness coefficient.

Effect of SiC-Cu Electrode on Material Removal Rate, Tool Wear and Surface Roughness in EDM Process

2020 ◽  
Vol 38 (9A) ◽  
pp. 1406-1413
Author(s):  
Yousif Q. Laibia ◽  
Saad K. Shather
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
304 Stainless Steel ◽  
Tool Electrode ◽  
Pulse Time ◽  
Edm Process

Electrical discharge machining (EDM) is one of the most common non-traditional processes for the manufacture of high precision parts and complex shapes. The EDM process depends on the heat energy between the work material and the tool electrode. This study focused on the material removal rate (MRR), the surface roughness, and tool wear in a 304 stainless steel EDM. The composite electrode consisted of copper (Cu) and silicon carbide (SiC). The current effects imposed on the working material, as well as the pulses that change over time during the experiment. When the current used is (8, 5, 3, 2, 1.5) A, the pulse time used is (12, 25) μs and the size of the space used is (1) mm. Optimum surface roughness under a current of 1.5 A and the pulse time of 25 μs with a maximum MRR of 8 A and the pulse duration of 25 μs.

Enhancement of EDM Performance by Using Copper-Silver Composite Electrode

2020 ◽  
Vol 38 (9A) ◽  
pp. 1352-1358
Author(s):  
Saad K. Shather ◽  
Abbas A. Ibrahim ◽  
Zainab H. Mohsein ◽  
Omar H. Hassoon
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
High Speed ◽  
Composite Electrode ◽  
Removal Rate ◽  
Pure Copper ◽  
High Speed Steel ◽  
Pulse On Time ◽  
Pulse Off Time

Discharge Machining is a non-traditional machining technique and usually applied for hard metals and complex shapes that difficult to machining in the traditional cutting process. This process depends on different parameters that can affect the material removal rate and surface roughness. The electrode material is one of the important parameters in Electro –Discharge Machining (EDM). In this paper, the experimental work carried out by using a composite material electrode and the workpiece material from a high-speed steel plate. The cutting conditions: current (10 Amps, 12 Amps, 14 Amps), pulse on time (100 µs, 150 µs, 200 µs), pulse off time 25 µs, casting technique has been carried out to prepare the composite electrodes copper-sliver. The experimental results showed that Copper-Sliver (weight ratio70:30) gives better results than commonly electrode copper, Material Removal Rate (MRR) Copper-Sliver composite electrode reach to 0.225 gm/min higher than the pure Copper electrode. The lower value of the tool wear rate achieved with the composite electrode is 0.0001 gm/min. The surface roughness of the workpiece improved with a composite electrode compared with the pure electrode.

Optimization of Cutting Parameters in Milling Process Using Genetic Algorithm and ANOVA (March 2020)

2020 ◽  
Vol 38 (10A) ◽  
pp. 1489-1503
Author(s):  
Marwa Q. Ibraheem
Keyword(s):  
Genetic Algorithm ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Optimal Value ◽  
Optimization Of Cutting Parameters

In this present work use a genetic algorithm for the selection of cutting conditions in milling operation such as cutting speed, feed and depth of cut to investigate the optimal value and the effects of it on the material removal rate and tool wear. The material selected for this work was Ti-6Al-4V Alloy using H13A carbide as a cutting tool. Two objective functions have been adopted gives minimum tool wear and maximum material removal rate that is simultaneously optimized. Finally, it does conclude from the results that the optimal value of cutting speed is (1992.601m/min), depth of cut is (1.55mm) and feed is (148.203mm/rev) for the present work.

Sign in / Sign up

Export Citation Format

Share Document