Influence of the Hub Endwall Cavity Flow on the Time-Averaged and Time-Resolved Aero-Thermodynamics of an Axial HP Turbine Stage

2002 ◽  
Author(s):  
R. De´nos ◽  
G. Paniagua
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Significant Influence ◽  
Total Pressure ◽  
Rotor Blade ◽  
Static Pressure ◽  
Cavity Flow ◽  
Turbine Stage ◽  
Time Resolved ◽  
Transonic Turbine

This experimental research investigates the influence of the hub endwall cavity flow on the aerodynamics and heat transfer of a high-pressure transonic turbine stage tested under engine representative conditions. The measurements include the hub and tip endwall static pressure downstream of the vane, the static pressure and heat transfer on the rotor blade at 15% span and on the hub platform as well as the stage downstream total pressure and temperature. Both steady and unsteady aspects are addressed. The hub endwall cavity flow has a significant influence on both the time-averaged and time-resolved components of the measured quantities. The effects are shown to be mainly due to an increase of the pitchwise averaged static pressure at hub downstream of the vane when cavity flow ejection is activated.

The Effects of Blade Passing on the Heat Transfer Coefficient of the Overtip Casing in a Transonic Turbine Stage

2008 ◽  
Vol 130 (4) ◽  
Author(s):  
Steven J. Thorpe ◽  
Roger W. Ainsworth
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Cooling System ◽  
Turbine Stage ◽  
Transfer Coefficients ◽  
Time Resolved ◽  
Turbine Engine ◽  
Transonic Turbine

In a modern gas turbine engine, the outer casing (shroud) of the shroudless high-pressure turbine is exposed to a combination of high flow temperatures and heat transfer coefficients. The casing is consequently subjected to high levels of convective heat transfer, a situation that is complicated by flow unsteadiness caused by periodic blade-passing events. In order to arrive at an overtip casing design that has an acceptable service life, it is essential for manufacturers to have appropriate predictive methods and cooling system configurations. It is known that both the flow temperature and boundary layer conductance on the casing wall vary during the blade-passing cycle. The current article reports the measurement of spatially and temporally resolved heat transfer coefficient (h) on the overtip casing wall of a fully scaled transonic turbine stage experiment. The results indicate that h is a maximum when a blade tip is immediately above the point in question, while the lower values of h are observed when the point is exposed to the rotor passage flow. Time-resolved measurements of static pressure are used to reveal the unsteady aerodynamic situation adjacent to the overtip casing wall. The data obtained from this fully scaled transonic turbine stage experiment are compared to previously published heat transfer data obtained in low-Mach number cascade-style tests of similar high-pressure blade geometries.

The Effects of Blade Passing on the Heat Transfer Coefficient of the Over-Tip Casing in a Transonic Turbine Stage

2006 ◽  
Author(s):  
Steven J. Thorpe ◽  
Roger W. Ainsworth
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Cooling System ◽  
Turbine Stage ◽  
Transfer Coefficients ◽  
Time Resolved ◽  
Turbine Engine ◽  
Transonic Turbine

In a modern gas turbine engine the outer casing (shroud) of the shroudless high-pressure turbine is exposed to a combination of high flow temperatures and heat transfer coefficients. The casing is consequently subjected to high levels of convective heat transfer, a situation that is complicated by flow unsteadiness caused by periodic blade-passing events. In order to arrive at an over-tip casing design that has an acceptable service life it is essential for manfacturers to have appropriate predictive methods and cooling system configurations. It is known that both the flow temperature and boundary layer conductance on the casing wall vary during the blade-passing cycle. The current article reports the measurement of spatially and temporally resolved heat transfer coefficient (h) on the over-tip casing wall of a fully-scaled transonic turbine stage experiment. The results indicate that h is a maximum when a blade-tip is immediately above the point in question, while lower values of h are observed when the point is exposed to the rotor passage flow. Time-resolved measurements of static pressure are used to reveal the unsteady aerodynamic situation adjacent to the over-tip casing wall. The data obtained from this fully-scaled transonic turbine stage experiment are compared to previously published heat transfer data obtained in low-Mach number cascade style tests of similar high pressure blade geometries.

Transonic Turbine Stage Heat Transfer Investigation in Presence of Strong Shocks

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
A. de la Loma ◽  
G. Paniagua ◽  
D. Verrastro ◽  
P. Adami
Keyword(s):  
Heat Transfer ◽  
Rotor Blade ◽  
Shock Interaction ◽  
Turbine Stage ◽  
Test Rig ◽  
Unsteady Heat Transfer ◽  
Tube Test ◽  
Stator Blade ◽  
Transonic Turbine ◽  
Layered Thin Film

This paper reports the external convective heat transfer distribution of a modern single-stage transonic turbine together with the physical interpretation of the different shock interaction mechanisms. The measurements have been performed in the compression tube test rig of the von Karman Institute using single- and double-layered thin film gauges. The three pressure ratios tested are representative of those encountered in actual aeroengines, with M2,is ranging from 1.07 to 1.25 and a Reynolds number of about 106. Three different rotor blade heights (15%, 50%, and 85%) and the stator blade at midspan have been investigated. The measurements highlight the destabilizing effect of the vane left-running shock on the rotor boundary layer. The stator unsteady heat transfer is dominated by the fluctuating right-running vane trailing edge shock at the blade passing frequency.

Design of a Transonic High-Pressure Turbine Stage 2D Section With Reduced Rotor/Stator Interaction

2004 ◽  
Author(s):  
Michele Vascellari ◽  
Re´my De´nos ◽  
Rene´ Van den Braembussche
Keyword(s):  
Rotor Blade ◽  
Static Pressure ◽  
Aerodynamic Force ◽  
Pressure Fluctuations ◽  
Uniform Field ◽  
Turbine Stage ◽  
Rotor Stator Interaction ◽  
Transonic Turbine ◽  
Blade Failure ◽  
Rotor Profiles

In transonic turbine stages, the exit static pressure field of the vane is highly non-uniform in the pitchwise direction. The rotor traverses periodically this non-uniform field and large static pressure fluctuations are observed around the rotor section. As a consequence the rotor blade is submitted to significant variations of its aerodynamic force. This contributes to the high cycle fatigue and may result in unexpected blade failure. In this paper an existing transonic turbine stage section is redesigned in the view of reducing the rotor stator interaction, and in particular the unsteady rotor blade forcing. The first step is the redesign of the stator blade profile to reduce the stator exit pitchwise static pressure gradient. For this purpose, a procedure using a genetic algorithm and an artificial neural network is used. Next, two new rotor profiles are designed and analysed with a quasi 3D Euler unsteady solver in order to investigate their receptivity to the shock interaction. One of the new profiles allows reducing the blade force variation by 50%.

Unsteady Rotor Heat Transfer in a Transonic Turbine Stage

2002 ◽  
Author(s):  
F. Didier ◽  
R. De´nos ◽  
T. Arts
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Strong Dependence ◽  
Convective Heat Transfer Coefficient ◽  
Operating Conditions ◽  
Turbine Stage ◽  
Trailing Edge ◽  
Time Resolved ◽  
Number Distribution ◽  
Transonic Turbine

This experimental investigation reports the convective heat transfer coefficient around the rotor of a transonic turbine stage. Both time-resolved and time-averaged aspects are addressed. The measurements are performed around the rotor blade at 15%, 50% and 85% span as well as on the rotor tip and the hub platform. Four operating conditions are tested covering two Reynolds numbers and three pressure ratios. The tests are performed in the compression tube turbine test rig CT3 of the von Karman Institute, allowing a correct simulation of the operating conditions encountered in modern aero-engines. The time-averaged Nusselt number distribution shows the strong dependence on both blade Mach number distribution and Reynolds number. The time-resolved heat transfer rate is mostly dictated by the vane trailing edge shock impingement on the rotor boundary layer. The shock passage corresponds to a sudden heat transfer increase. The effects are more pronounced in the leading edge region. The increase of the stage pressure ratio causes a stronger vane trailing edge shock and thus larger heat transfer fluctuations. The influence of the Reynolds number is hardly visible.

Comparison of Steady and Unsteady Coupled Heat-Transfer Simulations of a High-Pressure Turbine Blade

2015 ◽  
Author(s):  
Markus Schmidt ◽  
Christoph Starke
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Steady State ◽  
Flow Field ◽  
Film Cooling ◽  
Strong Increase ◽  
Pressure Side ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Time Resolved

This article presents results for the coupled simulation of a high-pressure turbine stage in consideration of unsteady hot gas flows. A semi-unsteady coupling process was developed to solve the conjugate heat transfer problem for turbine components of gas turbines. Time-resolved CFD simulations are coupled to a finite element solver for the steady state heat conduction inside of the blade material. A simplified turbine stage geometry is investigated in this paper to describe the influence of the unsteady flow field onto the time-averaged heat transfer. Comparisons of the time-resolved results to steady state results indicate the importance of a coupled simulation and the consideration of the time-dependent flow-field. Different film-cooling configurations for the turbine NGV are considered, resulting in different temperature and pressure deficits in the vane wake. Their contribution to non-linear effects causing the time-averaged heat load to differ from a steady result is discussed to further highlight the necessity of unsteady design methods for future turbine developments. A strong increase in the pressure side heat transfer coefficients for unsteady simulations is observed in all results. For higher film-cooling mass flows in the upstream row, the preferential migration of hot fluid towards the pressure side of a turbine blade is amplified as well, which leads to a strong increase in material temperature at the pressure side and also in the blade tip region.

Unsteady Rotor Heat Transfer in a Transonic Turbine Stage

2002 ◽  
Vol 124 (4) ◽  
pp. 614-622 ◽  
Author(s):  
F. Didier ◽  
R. De´nos ◽  
T. Arts
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Strong Dependence ◽  
Convective Heat Transfer Coefficient ◽  
Operating Conditions ◽  
Turbine Stage ◽  
Trailing Edge ◽  
Time Resolved ◽  
Number Distribution ◽  
Transonic Turbine

This experimental investigation reports the convective heat transfer coefficient around the rotor of a transonic turbine stage. Both time-resolved and time-averaged aspects are addressed. The measurements are performed around the rotor blade at 15, 50, and 85% span as well as on the rotor tip and the hub platform. Four operating conditions are tested covering two Reynolds numbers and three pressure ratios. The tests are performed in the compression tube turbine test rig CT3 of the von Karman Institute, allowing a correct simulation of the operating conditions encountered in modern aero-engines. The time-averaged Nusselt number distribution shows the strong dependence on both blade Mach number distribution and Reynolds number. The time-resolved heat transfer rate is mostly dictated by the vane trailing edge shock impingement on the rotor boundary layer. The shock passage corresponds to a sudden heat transfer increase. The effects are more pronounced in the leading edge region. The increase of the stage pressure ratio causes a stronger vane trailing edge shock and thus larger heat transfer fluctuations. The influence of the Reynolds number is hardly visible.

Three Dimensional Heat Transfer Analysis of High Pressure Turbine Blade

2009 ◽  
Author(s):  
A. Sipatov ◽  
L. Gomzikov ◽  
V. Latyshev ◽  
N. Gladysheva
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
High Pressure ◽  
Rotor Blade ◽  
Computational Analysis ◽  
Three Dimensional ◽  
Heat Transfer Analysis ◽  
Aircraft Engines ◽  
Turbine Stage ◽  
High Pressure Turbine

The present tendency of creating new aircraft engines with a higher level of fuel efficiency leads to the necessity to increase gas temperature at a high pressure turbine (HPT) inlet. To design such type of engines, the improvement of accuracy of the computational analysis is required. According to this the numerical analysis methods are constantly developing worldwide. The leading firms in designing aircraft engines carry out investigations in this field. However, this problem has not been resolved completely yet because there are many different factors affecting HPT blade heat conditions. In addition in some cases the numerical methods and approaches require tuning (for example to predict laminar-turbulent transition region or to describe the interaction of boundary layer and shock wave). In this work our advanced approach of blade heat condition numerical estimation based on the three-dimensional computational analysis is presented. The object of investigation is an advanced aircraft engine HPT first stage blade. The given analysis consists of two interrelated parts. The first part is a stator-rotor interaction modeling of the investigated turbine stage (unsteady approach). Solving this task we devoted much attention to modeling unsteady effects of stator-rotor interaction and to describing an influence of applied inlet boundary conditions on the blade heat conditions. In particular, to determine the total pressure, flow angle and total temperature distributions at the stage inlet we performed a numerical modeling of the combustor chamber of the investigated engine. The second part is a flow modeling in the turbine stage using flow parameters averaging on the stator-rotor interface (steady approach). Here we used sufficiently finer grid discretization to model all perforation holes on the stator vane and rotor blade, endwalls films in detail and to apply conjugate heat transfer approach for the rotor blade. Final results were obtained applying the results of steady and unsteady approaches. Experimental data of the investigated blade heat conditions are presented in the paper. These data were obtained during full size experimental testing the core of the engine and were collected using two different type of experimental equipment: thermocouples and thermo-crystals. The comparison of experimental data and final results meets the requirements of our investigation.

Transonic Turbine Stage Heat Transfer Investigation in Presence of Strong Shocks

2007 ◽  
Author(s):  
A. de la Loma ◽  
G. Paniagua ◽  
D. Verrastro ◽  
P. Adami
Keyword(s):  
Heat Transfer ◽  
Rotor Blade ◽  
Turbine Stage ◽  
Test Rig ◽  
Unsteady Heat Transfer ◽  
Tube Test ◽  
Stator Blade ◽  
Transonic Turbine ◽  
Aero Engines ◽  
Layered Thin Film

This paper reports the external convective heat transfer distribution of a modern single-stage transonic turbine together with the physical interpretation of the different shock interaction mechanisms. The measurements have been performed in the compression tube test rig of the von Karman Institute using single and double-layered thin film gauges. The three pressure ratios tested are representative of those encountered in actual aero-engines, with M2, is ranging from 1.07 to 1.25 and a Reynolds number of about 106. Three different rotor blade heights (15%, 50% and 85%) and the stator blade at mid-span have been investigated. The measurements highlight the destabilizing effect of the vane left running shock on the rotor boundary layer. The stator unsteady heat transfer is dominated by the fluctuating right running vane trailing edge shock at the blade passing frequency.

An Experimental Study of Film Cooling in a Rotating Transonic Turbine

1994 ◽  
Vol 116 (1) ◽  
pp. 63-70 ◽  
Author(s):  
R. S. Abhari ◽  
A. H. Epstein
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Test Facility ◽  
Turbine Stage ◽  
Suction Surface ◽  
Time Resolved ◽  
Pressure Surface ◽  
Transonic Turbine ◽  
Percent Decrease ◽  
Time Resolved Measurements

Time-resolved measurements of heat transfer on a fully cooled transonic turbine stage have been taken in a short duration turbine test facility, which simulates full engine nondimensional conditions. The time average of this data is compared to uncooled rotor data and cooled linear cascade measurements made on the same profile. The film cooling reduces the time-averaged heat transfer compared to the uncooled rotor on the blade suction surface by as much as 60 percent, but has relatively little effect on the pressure surface. The suction surface rotor heat transfer is lower than that measured in the cascade. The results are similar over the central 3/4 of the span, implying that the flow here is mainly two dimensional. The film cooling is shown to be much less effective at high blowing ratios than at low ones. Time-resolved measurements reveal that the cooling, when effective, both reduced the dc level of heat transfer and changed the shape of the unsteady waveform. Unsteady blowing is shown to be a principal driver of film cooling fluctuations, and a linear model is shown to do a good job in predicting the unsteady heat transfer. The unsteadiness results in a 12 percent decrease in heat transfer on the suction surface and a 5 percent increase on the pressure surface.

Sign in / Sign up

Export Citation Format

Share Document