Unsteady Aerodynamics and Interactions Between a High Pressure Turbine Vane and Rotor

2004 ◽  
Author(s):  
Ryan M. Urbassik ◽  
J. Mitch Wolff ◽  
Marc D. Polanka
Keyword(s):  
Experimental Data ◽  
High Pressure ◽  
Potential Field ◽  
Rotor Blade ◽  
Second Harmonic ◽  
Unsteady Aerodynamics ◽  
Pressure Measurements ◽  
High Pressure Turbine ◽  
Turbine Vane ◽  
Unsteady Pressure Measurements

A set of experimental data is presented investigating the unsteady aerodynamics associated with a high pressure turbine vane (HPV) and rotor blade (HPB). The data was acquired at the Turbine Research Facility (TRF) of the Air Force Research Laboratory. The TRF is a transient, blowdown facility generating several seconds of experimental data on full scale engine hardware at scaled turbine operating conditions simulating an actual engine environment. The pressure ratio and freestream Reynolds number were varied for this investigation. Surface unsteady pressure measurements on the HPV, total pressure traverse measurements downstream of the vane, and surface unsteady pressure measurements for the rotor blade were obtained. The unsteady content of the HPV surface was generated by the rotor potential field. The first harmonic decayed more rapidly than the second harmonic with a movement upstream causing the second harmonic to be most influential at the vane throat. The blade unsteadiness appears to be caused by a combination of shock, potential field, and vane wake interactions between the vane and rotor blade. The revolution averaged data resulted in higher unsteadiness than a passing ensemble average for both vane and rotor indicating a need to understand each passage for high cycle fatigue (HCF) effects.

Unsteady Aerodynamics and Interactions Between a High-Pressure Turbine Vane and Rotor

2004 ◽  
Vol 128 (1) ◽  
pp. 35-42 ◽  
Author(s):  
Ryan M. Urbassik ◽  
J. Mitch Wolff ◽  
Marc D. Polanka
Keyword(s):  
Experimental Data ◽  
High Pressure ◽  
Potential Field ◽  
Rotor Blade ◽  
Second Harmonic ◽  
Unsteady Aerodynamics ◽  
Pressure Measurements ◽  
High Pressure Turbine ◽  
Turbine Vane ◽  
Unsteady Pressure Measurements

A set of experimental data is presented investigating the unsteady aerodynamics associated with a high pressure turbine vane (HPV) and rotor blade (HPB). The data was acquired at the Turbine Research Facility (TRF) of the Air Force Research Laboratory. The TRF is a transient, blowdown facility generating several seconds of experimental data on full scale engine hardware at scaled turbine operating conditions simulating an actual engine environment. The pressure ratio and freestream Reynolds number were varied for this investigation. Surface unsteady pressure measurements on the HPV, total pressure traverse measurements downstream of the vane, and surface unsteady pressure measurements for the rotor blade were obtained. The unsteady content of the HPV surface was generated by the rotor potential field. The first harmonic decayed more rapidly than the second harmonic with a movement upstream causing the second harmonic to be most influential at the vane throat. The blade unsteadiness appears to be caused by a combination of shock, potential field, and vane wake interactions between the vane and rotor blade. The revolution averaged data resulted in higher unsteadiness than a passing ensemble average for both vane and rotor indicating a need to understand each passage for high cycle fatigue (HCF) effects.

Three Dimensional Heat Transfer Analysis of High Pressure Turbine Blade

2009 ◽  
Author(s):  
A. Sipatov ◽  
L. Gomzikov ◽  
V. Latyshev ◽  
N. Gladysheva
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
High Pressure ◽  
Rotor Blade ◽  
Computational Analysis ◽  
Three Dimensional ◽  
Heat Transfer Analysis ◽  
Aircraft Engines ◽  
Turbine Stage ◽  
High Pressure Turbine

The present tendency of creating new aircraft engines with a higher level of fuel efficiency leads to the necessity to increase gas temperature at a high pressure turbine (HPT) inlet. To design such type of engines, the improvement of accuracy of the computational analysis is required. According to this the numerical analysis methods are constantly developing worldwide. The leading firms in designing aircraft engines carry out investigations in this field. However, this problem has not been resolved completely yet because there are many different factors affecting HPT blade heat conditions. In addition in some cases the numerical methods and approaches require tuning (for example to predict laminar-turbulent transition region or to describe the interaction of boundary layer and shock wave). In this work our advanced approach of blade heat condition numerical estimation based on the three-dimensional computational analysis is presented. The object of investigation is an advanced aircraft engine HPT first stage blade. The given analysis consists of two interrelated parts. The first part is a stator-rotor interaction modeling of the investigated turbine stage (unsteady approach). Solving this task we devoted much attention to modeling unsteady effects of stator-rotor interaction and to describing an influence of applied inlet boundary conditions on the blade heat conditions. In particular, to determine the total pressure, flow angle and total temperature distributions at the stage inlet we performed a numerical modeling of the combustor chamber of the investigated engine. The second part is a flow modeling in the turbine stage using flow parameters averaging on the stator-rotor interface (steady approach). Here we used sufficiently finer grid discretization to model all perforation holes on the stator vane and rotor blade, endwalls films in detail and to apply conjugate heat transfer approach for the rotor blade. Final results were obtained applying the results of steady and unsteady approaches. Experimental data of the investigated blade heat conditions are presented in the paper. These data were obtained during full size experimental testing the core of the engine and were collected using two different type of experimental equipment: thermocouples and thermo-crystals. The comparison of experimental data and final results meets the requirements of our investigation.

scholarly journals Unsteady Interaction Between a Transonic Turbine Stage and Downstream Components

2004 ◽  
Vol 10 (6) ◽  
pp. 495-506 ◽  
Author(s):  
Roger L. Davis ◽  
Jixian Yao ◽  
John P. Clark ◽  
Gary Stetson ◽  
Juan J. Alonso ◽  
...  
Keyword(s):  
Experimental Data ◽  
High Pressure ◽  
Surface Pressure ◽  
Low Pressure ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Unsteady Pressure ◽  
Low Pressure Turbine ◽  
Unsteady Surface Pressure ◽  
Turbine Vane

Results from a numerical simulation of the unsteady flow through one quarter of the circumference of a transonic high-pressure turbine stage, transition duct, and low-pressure turbine first vane are presented and compared with experimental data. Analysis of the unsteady pressure field resulting from the simulation shows the effects of not only the rotor/stator interaction of the high-pressure turbine stage but also new details of the interaction between the blade and the downstream transition duct and low-pressure turbine vane. Blade trailing edge shocks propagate downstream, strike, and reflect off of the transition duct hub and/or downstream vane leading to high unsteady pressure on these downstreamcomponents. The reflection of these shocks from the downstream components back into the blade itself has also been found to increase the level of unsteady pressure fluctuations on the uncovered portion of the blade suction surface. In addition, the blade tip vortex has been found to have a moderately strong interaction with the downstream vane even with the considerable axial spacing between the two blade-rows. Fourier decomposition of the unsteady surface pressure of the blade and downstream low-pressure turbine vane shows the magnitude of the various frequencies contributing to the unsteady loads. Detailed comparisons between the computed unsteady surface pressure spectrum and the experimental data are shown along with a discussion of the various interaction mechanisms between the blade, transition duct, and downstream vane. These comparisons show-overall good agreement between the simulation and experimental data and identify areas where further improvements in modeling are needed.

scholarly journals Unsteady Interaction Between a Transonic Turbine Stage and Downstream Components

2002 ◽  
Author(s):  
Roger L. Davis ◽  
Jixian Yao ◽  
John P. Clark ◽  
Gary Stetson ◽  
Juan J. Alonso ◽  
...  
Keyword(s):  
Experimental Data ◽  
High Pressure ◽  
Surface Pressure ◽  
Low Pressure ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Unsteady Pressure ◽  
Low Pressure Turbine ◽  
Unsteady Surface Pressure ◽  
Turbine Vane

Results from a numerical simulation of the unsteady flow through one quarter of the circumference of a transonic high-pressure turbine stage, transition duct, and low-pressure turbine first vane are presented and compared with experimental data. Analysis of the unsteady pressure field resulting from the simulation shows the effects of not only the rotor/stator interaction of the high-pressure turbine stage but also new details of the interaction between the blade and the downstream transition duct and low-pressure turbine vane. Blade trailing edge shocks propagate downstream, strike, and reflect off of the transition duct hub and/or downstream vane leading to high unsteady pressure on these downstream components. The reflection of these shocks from the downstream components back into the blade itself has also been found to increase the level of unsteady pressure fluctuations on the uncovered portion of the blade suction surface. In addition, the blade tip vortex has been found to have a moderately strong interaction with the downstream vane even with the considerable axial spacing between the two blade-rows. Fourier decomposition of the unsteady surface pressure of the blade and downstream low-pressure turbine vane shows the magnitude of the various frequencies contributing to the unsteady loads. Detailed comparisons between the computed unsteady surface pressure spectrum and the experimental data are shown along with a discussion of the various interaction mechanisms between the blade, transition duct, and downstream vane. These comparisons show overall good agreement between the simulation and experimental data and identify areas where further improvements in modeling are needed.

Time-Averaged and Time-Accurate Aerodynamic Effects of Forward Rotor Cavity Purge Flow for a High-Pressure Turbine: Part I—Analytical and Experimental Comparisons

2012 ◽  
Author(s):  
Brian R. Green ◽  
Randall M. Mathison ◽  
Michael G. Dunn
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Unsteady Aerodynamics ◽  
Flow Path ◽  
Field Analysis ◽  
High Pressure Turbine ◽  
Purge Flow

The effect of rotor purge flow on the unsteady aerodynamics of a high-pressure turbine stage operating at design corrected conditions has been investigated both experimentally and computationally. The experimental configuration consisted of a single-stage high-pressure turbine with a modern film-cooling configuration on the vane airfoil as well as the inner and outer end-wall surfaces. Purge flow was introduced into the cavity located between the high-pressure vane and the high-pressure disk. The high-pressure blades and the downstream low-pressure turbine nozzle row were not cooled. All hardware featured an aerodynamic design typical of a commercial high-pressure ratio turbine, and the flow path geometry was representative of the actual engine hardware. In addition to instrumentation in the main flow path, the stationary and rotating seals of the purge flow cavity were instrumented with high frequency response, flush-mounted pressure transducers and miniature thermocouples to measure flow field parameters above and below the angel wing. Predictions of the time-dependent flow field in the turbine flow path were obtained using FINE/Turbo, a three-dimensional, Reynolds-Averaged Navier-Stokes CFD code that had the capability to perform both steady and unsteady analysis. The steady and unsteady flow fields throughout the turbine were predicted using a three blade-row computational model that incorporated the purge flow cavity between the high-pressure vane and disk. The predictions were performed in an effort to mimic the design process with no adjustment of boundary conditions to better match the experimental data. The time-accurate predictions were generated using the harmonic method. Part I of this paper concentrates on the comparison of the time-averaged and time-accurate predictions with measurements in and around the purge flow cavity. The degree of agreement between the measured and predicted parameters is described in detail, providing confidence in the predictions for flow field analysis that will be provided in Part II.

Aerodynamic Performance of an Unlocated High Pressure Turbine Rotor With Worn Tip Seal Fins

2017 ◽  
Author(s):  
Lucas Pawsey ◽  
David John Rajendran ◽  
Vassilios Pachidis
Keyword(s):  
High Pressure ◽  
Rotor Blade ◽  
Turbine Rotor ◽  
Aerodynamic Performance ◽  
Axial Displacement ◽  
High Pressure Turbine ◽  
Design Modification ◽  
Turbine Casing ◽  
Secondary Air ◽  
Shaft Failure

An unlocated shaft failure in the high pressure turbine spool of an engine may result in a complex orbiting motion along with rearward axial displacement of the high pressure turbine rotor sub-assembly. This is due to the action of resultant forces and limitations imposed by constraints such as the bearings and turbine casing. Such motion of the rotor following an unlocated shaft failure, results in the development of multiple contacts between the components of the rotor sub-assembly, the turbine casing, and the downstream stator casing. Typically, in the case of shrouded rotor blades, the tip region is in the form of a seal with radial protrusions called ‘fins’ between the rotor blade and the turbine casing. The contact between the rotor blade and the turbine casing will therefore result in excessive wear of the tip seal fins, resulting in changes in the geometry of the tip seal domain that affects the characteristics of the tip leakage vortex. The rotor sub-assembly with worn seals may also be axially displaced rearwards, and consequent to this displacement, changes in the geometry of the rotor blade may occur because of the contact between the rotor sub-assembly and the downstream stator casing. An integrated approach of structural analyses, secondary air system dynamics, and 3D CFD is adopted in the present study to quantify the effect of the tip seal damage and axial displacement on the aerodynamic performance of the turbine stage. The resultant geometry after wearing down of the fins in the tip seal, and rearward axial displacement of the rotor sub-assembly is obtained from LS-DYNA simulations. 3D RANS analyses are carried out to quantify the aerodynamic performance of the turbine with worn fins in the tip seal at three different axial displacement locations i.e. 0 mm, 10 mm and 15 mm. The turbine performance parameters are then compared with equivalent cases in which the fins in the tip seal are intact for the same turbine axial displacement locations. From this study it is noted that the wearing of tip seal fins results in reduced turbine torque, power output and efficiency, consequent to changes in the flow behaviour in the turbine passages. The reduction in turbine torque will result in the reduction of the terminal speed of the rotor during an unlocated shaft failure. Therefore, a design modification that can lead to rapid wearing of the fins in the tip seal after an unlocated shaft failure holds promise for the management of a potential over-speed event.

Numerical Simulation of Deposition Phenomena on High-Pressure Turbine Vane Using UPACS

2019 ◽  
Author(s):  
Kenta Mizutori ◽  
Koji Fukudome ◽  
Makoto Yamamoto ◽  
Masaya Suzuki
Keyword(s):  
Numerical Simulation ◽  
High Pressure ◽  
Flow Field ◽  
Pressure Loss ◽  
Total Pressure ◽  
Total Pressure Loss ◽  
High Pressure Turbine ◽  
Pressure Loss Coefficient ◽  
Turbine Vane ◽  
Total Pressure Loss Coefficient

Abstract We performed numerical simulation to understand deposition phenomena on high-pressure turbine vane. Several deposition models were compared and the OSU model showed good adaptation to any flow field and material, so it was implemented on UPACS. After the implementation, the simulations of deposition phenomenon in several cases of the flow field were conducted. From the results, particles adhere on the leading edge and the trailing edge side of the pressure surface. Also, the calculation of the total pressure loss coefficient was conducted after computing the flow field after deposition. The total pressure loss coefficient increased after deposition and it was revealed that the deposition deteriorates aerodynamic performance.

Experimental Investigation of Vane Clocking in a One and 1/2 Stage High Pressure Turbine

2004 ◽  
Author(s):  
Charles W. Haldeman ◽  
Michael G. Dunn ◽  
John W. Barter ◽  
Brian R. Green ◽  
Robert F. Bergholz
Keyword(s):  
High Pressure ◽  
Low Pressure ◽  
Test Facility ◽  
Maximum Efficiency ◽  
High Pressure Turbine ◽  
Data Set ◽  
Time Resolved ◽  
Low Pressure Turbine ◽  
Turbine Vane ◽  
Vane Clocking

Aerodynamic measurements were acquired on a modern single-stage, transonic, high-pressure turbine with the adjacent low-pressure turbine vane row (a typical civilian one and one-half stage turbine rig) to observe the effects of low-pressure turbine vane clocking on overall turbine performance. The turbine rig (loosely referred to in this paper as the stage) was operated at design corrected conditions using the Ohio State University Gas Turbine Laboratory Turbine Test Facility (TTF). The research program utilized uncooled hardware in which all three airfoils were heavily instrumented at multiple spans to develop a full clocking dataset. The low-pressure turbine vane row (LPTV) was clocked relative to the high-pressure turbine vane row (HPTV). Various methods were used to evaluate the influence of clocking on the aeroperformance (efficiency) and the aerodynamics (pressure loading) of the LPTV, including time-resolved and time-averaged measurements. A change in overall efficiency of approximately 2–3% due to clocking effects is demonstrated and could be observed using a variety of independent methods. Maximum efficiency is obtained when the time-average surface pressures are highest on the LPTV and the time-resolved surface pressure (both in the time domain and frequency domain) show the least amount of variation. The overall effect is obtained by integrating over the entire airfoil, as the three-dimensional effects on the LPTV surface are significant. This experimental data set validates several computational research efforts that suggested wake migration is the primary reason for the perceived effectiveness of vane clocking. The suggestion that wake migration is the dominate mechanism in generating the clocking effect is also consistent with anecdotal evidence that fully cooled engine rigs do not see a great deal of clocking effect. This is consistent since the additional disturbances induced by the cooling flows and/or the combustor make it extremely difficult to find an alignment for the LPTV given the strong 3D nature of modern high-pressure turbine flows.

scholarly journals Optimization of Friction Damper Weight, Simulation and Experiments

1997 ◽  
Author(s):  
Gabor Csaba ◽  
Magnus Andersson
Keyword(s):  
Experimental Data ◽  
High Pressure ◽  
Turbine Blades ◽  
Turbine Rotor ◽  
Friction Damper ◽  
High Pressure Turbine ◽  
Coupled Modes ◽  
Modes Of Vibration ◽  
Damper Design ◽  
The Right

A new friction damper has been designed by Volvo Aero Corporation. It is used in the high pressure turbine stage of a turbojet engine. The objective of this paper was to find the optimal weight of the new damper that minimizes the blade response amplitude for six and nine engine order excitation and to compare the new damper design with that currently used. Another objective was to compare how well simulation results agree with experimental results from spin pit tests. Simulations were made with a damper model that incorporates the possibility of both micro- and macro-slip in the blade-damper contact interface. Turbine blades were modeled using finite element beam elements. Experimental data were provided from spin pit tests with a completely bladed high pressure turbine rotor. Results show that the simulation model can be used to give qualitative results but has to be further developed to incorporate mistuning effects and coupled modes of vibration for the blade. The spin pit test shows that the new damper design is more efficient in reducing resonance stresses than the old design. It was not possible to see if simulations predict the right optimal damper weight by comparing with experimental data because the rotor could not be excited up to the design point.

Sign in / Sign up

Export Citation Format

Share Document