The Effects of IGV Wake Impingement on the Boundary Layer and the Near-Wake of a Rotor Blade

2008 ◽  
Author(s):  
Francesco Soranna ◽  
Yi-Chih Chow ◽  
Oguz Uzol ◽  
Joseph Katz
Keyword(s):  
Boundary Layer ◽  
Rotor Blade ◽  
Guide Vane ◽  
Shear Velocity ◽  
Inlet Guide Vane ◽  
Surface Boundary ◽  
Momentum Thickness ◽  
Suction Surface ◽  
Near Wake ◽  
Trailing Edge

This paper examines the response of a rotor blade boundary layer and a rotor near-wake to an impinging wake of an Inlet Guide Vane (IGV) located upstream of the rotor blade. Two-dimensional Particle Image Velocimetry (PIV) measurements are performed in a refractive index matched turbomachinery facility that provides unobstructed view of the entire flow field. Data obtained at several rotor phases enables us to examine IGV-wake-induced changes to the structure of the boundary layer and how these changes affect the flow and turbulence within the rotor near-wake. We focus on the suction surface boundary layer, near the blade trailing edge, but analyze the evolution of both the pressure and suction sides of the near-wake. During IGV-wake impingement, the boundary layer becomes significantly thinner, with lower momentum thickness and more stable profile compared to other phases at the same location. Analysis of available terms in the integral momentum equation indicates that the phase-averaged unsteady term is the main contributor to the decrease in momentum thickness within the impinging wake. Thinning of the boundary/shear layer extends into the rotor near wake, making it narrower and increasing the phase averaged shear velocity gradients and associated turbulent kinetic energy (TKE) production rate. Consequently, the TKE increases during wake thinning, with as much as 75% phase-dependent variations in its peak magnitude. The paper introduces a new way of looking at PIV data by defining a wake oriented coordinate system which enables to study the structure of turbulence around the trailing edge in great detail.

The Effects of Inlet Guide Vane-Wake Impingement on the Boundary Layer and the Near-Wake of a Rotor Blade

2010 ◽  
Vol 132 (4) ◽  
Author(s):  
Francesco Soranna ◽  
Yi-Chih Chow ◽  
Oguz Uzol ◽  
Joseph Katz
Keyword(s):  
Boundary Layer ◽  
Rotor Blade ◽  
Guide Vane ◽  
Shear Velocity ◽  
Inlet Guide Vane ◽  
Surface Boundary ◽  
Momentum Thickness ◽  
Suction Surface ◽  
Near Wake ◽  
Trailing Edge

This paper examines the response of a rotor blade boundary layer and a rotor near-wake to an impinging wake of an inlet guide vane (IGV) located upstream of the rotor blade. Two-dimensional particle image velocimetry (PIV) measurements are performed in a refractive index matched turbomachinery facility that provides unobstructed view of the entire flow field. Data obtained at several rotor phases enable us to examine the IGV-wake-induced changes to the structure of the boundary layer and how these changes affect the flow and turbulence within the rotor near-wake. We focus on the suction surface boundary layer, near the blade trailing edge, but analyze the evolution of both the pressure and suction sides of the near-wake. During the IGV-wake impingement, the boundary layer becomes significantly thinner, with lower momentum thickness and more stable profile compared with other phases at the same location. Analysis of available terms in the integral momentum equation indicates that the phase-averaged unsteady term is the main contributor to the decrease in momentum thickness within the impinging wake. Thinning of the boundary/shear layer extends into the rotor near-wake, making it narrower and increasing the phase-averaged shear velocity gradients and associated turbulent kinetic energy (TKE) production rate. Consequently, the TKE increases during wake thinning, with as much as 75% phase-dependent variations in its peak magnitude. This paper introduces a new way of looking at the PIV data by defining a wake-oriented coordinate system, which enables to study the structure of turbulence around the trailing edge in great detail.

scholarly journals Experimental Investigation on Spatial Development of Streamwise Vortices in a Turbine Inlet Guide Vane Cascade

1985 ◽  
Author(s):  
Toyotaka Sonoda
Keyword(s):  
Boundary Layer ◽  
Guide Vane ◽  
Leading Edge ◽  
Horseshoe Vortex ◽  
Spatial Development ◽  
Inlet Guide Vane ◽  
Surface Boundary ◽  
Streamwise Vortices ◽  
Suction Surface ◽  
Turbine Inlet

In order to obtain a better understanding of secondary flow in a turbine cascade, spatial development of a leading-edge horseshoe vortex has been investigated experimentally in a large-scale, low-speed, high-accelerated, plane turbine inlet guide vane cascade. Flow has been visualized by issuing kerosene vapor into the inlet boundary layer and the vane suction surface boundary layer, respectively. Based on many cross-sectional photographs normal to the flow and supplemental measurements of the wall static pressure on the vane and the endwall, the evolution of a leading-edge horseshoe vortex into streamwise vortices and the generation of a new type streamwise vortex pair on the suction surface near the endwall are discussed.

Structure and Decay Characteristics of Turbulence in the Near and Far-Wake of a Moderately Loaded Compressor Rotor-Blade

1981 ◽  
Vol 103 (1) ◽  
pp. 131-140 ◽  
Author(s):  
A. Ravindranath ◽  
B. Lakshminarayana
Keyword(s):  
Rotor Blade ◽  
Guide Vane ◽  
Three Dimensional ◽  
Inlet Guide Vane ◽  
Near Wake ◽  
Trailing Edge ◽  
Free Stream Turbulence ◽  
Compressor Rotor ◽  
Wake Turbulence ◽  
Far Wake

The wake of a turbomachinery rotor-blade is turbulent, highly three-dimensional, and nonisotropic with appreciable curvature in the trailing-edge and near-wake regions. The characteristics of the turbulence vary considerably with radius, blade loading, free-stream turbulence, Reynolds number, and the rotor-blade geometry. This paper is concerned with the turbulence properties of a moderately loaded compressor blade, particularly near the blade trailing-edge. The tangential variation of the axial, tangential and radial intensities and stresses across the wake, as well as their decay characteristics were measured with a tri-axial hot-wire probe in the rotor frame of reference. The decay of intensities and stresses were found to be very rapid in the trailing-edge and near-wake regions and slow in the far-wake region. The effects of inlet-guide-vane and the hub-wall boundary layers on the rotor wake turbulence spectra are also discussed. Similarity rules for the three components of intensity are also derived and presented in this paper.

Structure of Turbulence Around the Trailing Edge of a Rotor Blade

2007 ◽  
Author(s):  
Francesco Soranna ◽  
Yi-Chih Chow ◽  
Oguz Uzol ◽  
Joseph Katz
Keyword(s):  
Boundary Layer ◽  
Kinetic Energy ◽  
Turbulent Kinetic Energy ◽  
Production Rate ◽  
Rotor Blade ◽  
Streamwise Velocity ◽  
Small Region ◽  
Shear Strain Rate ◽  
Suction Surface ◽  
Trailing Edge

This paper focuses on the structure of turbulence around the trailing edge of a rotor blade operating behind a row of Inlet Guide Vanes (IGVs) located upstream of the rotor. High resolution, two-dimensional Particle Image Velocimetry (PIV) measurements are conducted in a refractive index matched turbomachinery facility that provides unobstructed view of the entire flow field. We focus on a small region around the rotor blade trailing edge, extending from 0.04c upstream of the trailing edge to about 0.1c downstream of it, c being the blade chord length. We examine the phase dependent distribution of turbulent kinetic energy (TKE) and its in-plane components of production rate. Impingement of an IGV wake on the suction surface of a rotor blade, near the trailing edge region, reduces the thickness of the boundary layer within the region impinged by the wake. The resulting increase in phase averaged shear strain rate increases the production rate and causes a striking increase in peak turbulent kinetic energy in the near wake. Streamwise velocity gradients, i.e. compression, also contribute to turbulence production, especially when the boundary layer at trailing edge is relatively thick, i.e. when it is not impinged by the IGV wake.

Unsteady Interaction Effects on a Transitional Turbine Blade Boundary Layer

1989 ◽  
Vol 111 (2) ◽  
pp. 162-168 ◽  
Author(s):  
D. A. Ashworth ◽  
J. E. LaGraff ◽  
D. L. Schultz
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Guide Vane ◽  
Turbine Rotor ◽  
Surface Boundary ◽  
Suction Surface ◽  
Wide Bandwidth ◽  
Free Stream Turbulence

Results are presented illustrating the detailed behavior of the suction surface boundary layer of a transonic gas turbine rotor in a two-dimensional cascade under the influence of both free-stream turbulence and simulated nozzle guide vane wakes and shocks. The instrumentation included thin film resistance thermometers along with electrical analogues of the one-dimensional heat conduction equations to obtain wide bandwidth heat transfer rate measurements in a short duration wind tunnel. This instrumentation provides sufficient time resolution to track individual wake and shock-related events and also the turbulent bursts of a transitional boundary layer. Wide bandwidth surface pressure transducers and spark Schlieren photography were used in support of these heat transfer measurements. The results showed a direct relationship between the passage of wake disturbances and transient surface heat transfer enhancements. It was possible to track both wake and transitional events along the surface and to compare these with the expected convection rates. Analysis of the signals allowed direct calculations of intermittency factors, which compared well with predictions. Additional effects due to a moving shock/boundary layer interaction were investigated. These resulted in marked variations in heat transfer rate both above and below the laminar values. These excursions were associated with separation and re-attachment phenomena.

Gill Slot Trailing Edge Heat Transfer: Effects of Blowing Rate, Reynolds Number, and External Turbulence on Heat Transfer and Film Cooling Effectiveness

2007 ◽  
Author(s):  
F. E. Ames ◽  
N. J. Fiala ◽  
J. D. Johnson
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Drop ◽  
Film Cooling ◽  
Guide Vane ◽  
Surface Boundary ◽  
Suction Surface ◽  
Trailing Edge ◽  
Film Cooling Effectiveness ◽  
Pin Fin

Heat transfer and film cooling distributions have been acquired downstream from the exit of a nozzle guide vane gill slot (or cutback). Additionally, heat transfer and pressure drop data have been experimentally determined for a pin fin array within the gill slot geometry. Generally, average row pin fin heat transfer levels for the converging channel correlate quite well with archival literature. However, no generalized flow friction factor correlation was found to predict the pressure drop within the array. Experimental data for the region downstream from the gill slot have been acquired over a four to one range in vane exit condition Reynolds number, with low, grid, and aero-combustor turbulence conditions. At these conditions, both heat transfer and adiabatic film cooling distributions have been documented over a range of blowing ratios. Heat transfer distributions downstream from the gill slot ejection were found to be dependent on both ejection flow rate and external conditions. Generally, adiabatic film cooling levels are high but dissipate toward the trailing edge and provide some protection on the trailing edge. Heat transfer levels on the trailing edge are affected largely by the chord exit Reynolds number and the suction surface boundary layer condition. The present paper, together with a companion paper which documents gill slot aerodynamics, is intended to provide designers with the heat transfer and aerodynamic loss information needed to compare competing trailing edge designs.

On the Flow and Turbulence Within the Wake and Boundary Layer of a Rotor Blade Located Downstream of an IGV

2003 ◽  
Author(s):  
Yi-Chih Chow ◽  
Oguz Uzol ◽  
Joseph Katz
Keyword(s):  
Boundary Layer ◽  
Spectral Analysis ◽  
Rotor Blade ◽  
Hot Spot ◽  
Wake Flow ◽  
Mean Flow ◽  
Production Rates ◽  
Near Wake ◽  
Trailing Edge ◽  
Planar Shear

This paper presents detailed experimental data on the flow and turbulence within the wake and boundary layer of a rotor blade operating behind a row of Inlet Guide Vanes (IGVs). The experiments are performed in a refractive index matched facility that provides an unobstructed view of the entire flow field. Results of the high-resolution 2D Particle Image Velocimetry (PIV) measurements are used for characterizing the mean flow, Reynolds stresses, turbulent kinetic energy as well as dissipation and production rates. Dissipation and production rates are high and of the same order of magnitude near the trailing edge, and decrease rapidly with increasing distance from the blade. The trend is reversed in the wake kinking region, resulting in elevated turbulence levels, i.e. a turbulent hot spot. One-dimensional spectral analysis shows that, except for the very near wake and hot-spot regions, the turbulence within the rotor wake can be assumed to be isotropic. Also the directions of the maximum shear strain and shear stress are aligned in that region, i.e. consistent with eddy viscosity type Reynolds stress models. The rotor near wake mainly consists of two parallel layers experiencing planar shear with opposite signs as one would expect to find in a 2D wake. However, orientation differences can extend up to 45° near the trailing edge and the hot-spot. Furthermore, there is substantial mismatch in the location of the local maxima of stresses and strains. The values of S33 are also large there, indicating that the flow is three-dimensional. Rotor boundary layer measurements focus on a region where the IGV wake intersects with the rotor blade. The impingement of the increased axial velocity region in between the IGV wakes causes the thinning of the boundary layer. This is similar to the effect of a turbulent jet impinging on a flat surface. When viewed in the frame of reference of “non-wake” flow regions, the boundary layer thinning can also be attributed to the suction (or “negative jet”) effect of the “slip velocity” present in the IGV wake segments. Spectral analysis shows that the turbulence in the rotor boundary layer is highly anisotropic. As a result, the spectra cannot be used for estimating the dissipation rate.

Simulation of the Effects of Shock Wave Passing on a Turbine Rotor Blade

1985 ◽  
Vol 107 (4) ◽  
pp. 998-1006 ◽  
Author(s):  
D. J. Doorly ◽  
M. L. G. Oldfield
Keyword(s):  
Boundary Layer ◽  
Shock Wave ◽  
Shock Waves ◽  
High Frequency ◽  
Guide Vane ◽  
Turbine Rotor ◽  
Surface Boundary ◽  
Suction Surface ◽  
Very High Frequency ◽  
And Shock Waves

The unsteady effects of shock waves and wakes shed by the nozzle guide vane row on the flow over a downstream turbine rotor have been simulated in a transient cascade tunnel. At conditions representative of engine flow, both wakes and shock waves are shown to cause transient turbulent patches to develop in an otherwise laminar (suction-surface) boundary layer. The simulation technique employed, coupled with very high-frequency heat transfer and pressure measurements, and flow visualization, allowed the transition initiated by isolated wakes and shock waves to be studied in detail. On the profile tested, the comparatively weak shock waves considered do not produce significant effects by direct shock-boundary layer interaction. Instead, the shock initiates a leading edge separation, which subsequently collapses, leaving a turbulent patch that is convected downstream. Effects of combined wake- and shock wave-passing at high frequency are also reported.

scholarly journals Heat Transfer Measurements of a Transonic Nozzle Guide Vane

1982 ◽  
Author(s):  
M. R. Litchfield ◽  
R. J. G. Norton
Keyword(s):  
Heat Transfer ◽  
Guide Vane ◽  
Wedge Angle ◽  
Differential Method ◽  
Surface Boundary ◽  
Suction Surface ◽  
Trailing Edge ◽  
Slow Increase ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

The heat transfer and aerodynamic characteristics of a turbine nozzle guide vane with a supersonic exit velocity have been measured in a transient cascade facility. The vane possesses a convergent-divergent passage, and this, together with a low trailing edge wedge angle, is seen to control the supersonic flow efficiently at design conditions. Heat transfer measurements have been taken on both suction and pressure surfaces. On the suction surface, transition is marked by a rapid increase in heat transfer, whereas on the pressure surface a slow increase in heat transfer indicates the gradual onset of turbulence. The measurements also indicate possible relaminarisation of the suction surface boundary layer at the impingement of the trailing edge shock. Predictions are presented of aerodynamic flow, using an inviscid time-marching calculation, and heat transfer, using a differential method applied to the vane surface.

An Experimental Study of Heat Transfer on an Outlet Guide Vane

2014 ◽  
Author(s):  
Chenglong Wang ◽  
Lei Wang ◽  
Bengt Sundén ◽  
Valery Chernoray ◽  
Hans Abrahamsson
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Reynolds Number ◽  
Turbulent Boundary Layer ◽  
Guide Vane ◽  
Incidence Angle ◽  
Boundary Layer Transition ◽  
Transfer Coefficients ◽  
Suction Surface ◽  
Layer Transition

In the present study, the heat transfer characteristics on the suction and pressure sides of an outlet guide vane (OGV) are investigated by using liquid crystal thermography (LCT) method in a linear cascade. Because the OGV has a complex curved surface, it is necessary to calibrate the LCT by taking into account the effect of viewing angles of the camera. Based on the calibration results, heat transfer measurements of the OGV were conducted. Both on- and off-design conditions were tested, where the incidence angles of the OGV were 25 degrees and −25 degrees, respectively. The Reynolds numbers, based on the axial flow velocity and the chord length, were 300,000 and 450,000. In addition, heat transfer on suction side of the OGV with +40 degrees incidence angle was measured. The results indicate that the Reynolds number and incidence angle have considerable influences upon the heat transfer on both pressure and suction surfaces. For on-design conditions, laminar-turbulent boundary layer transitions are on both sides, but no flow separation occurs; on the contrary, for off-design conditions, the position of laminar-turbulent boundary layer transition is significantly displaced downstream on the suction surface, and a separation occurs from the leading edge on the pressure surface. As expected, larger Reynolds number gives higher heat transfer coefficients on both sides of the OGV.

Sign in / Sign up

Export Citation Format

Share Document